User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
Menus and Parameters
2-45
BreezeACCESS Version 4.3 System Manual
Table 2-4 -.: Transmit Power Output
Power Level - Applicable to all SU-R units and to SU-I/AU-I units.
Sets the transmit level according to the unit’s specifications.
In SU-R units there are two options:
High – An output power level to the antenna port of 28 dBm
Low – An output power level to the antenna port of 17 dBm
In SU-I/I-D and AU-I/I-D there are two options:
High– An output power level to the antenna port of 17 dBm
Low – An output power level to the antenna port of 10 dBm
The default is High.
ATPC Parameters in IF Based AU
ATPC Option: To enable or disable the Automatic Transmit
Power Control (ATPC) algorithm.
The default is Disable.
Cable
attenuation
0dB 5dB 10dB 15dB
Transmit power
Control
Outdoor power
(dBm)
Outdoor power
(dBm)
Outdoor power
(dBm)
Outdoor power
(dBm)
15 24+/- 2 24+/- 2 24+/- 2 24+/- 2
14 24+/- 2 24+/- 2 24+/- 2 24+/- 2
13 24+/- 2 24+/- 2 24+/- 2 24+/- 2
12 23+/- 3 23+/- 3 23+/- 3 23+/- 3
11 23+/- 3 23+/- 3 23+/- 3 23+/- 3
10 23+/- 3 23+/- 3 23+/- 3 23+/- 3
9 23+/- 3 23+/- 3 22+/- 3 22+/- 3
8 23+/- 3 23+/- 3 22+/- 4 21+/- 4
7 22+/- 4 23+/- 3 21+/- 4 20+/- 4
6 22+/- 4 22+/- 4 20+/- 4 17+/- 4
5 22+/- 4 21+/- 4 19+/- 4 15+/- 4
4 21+/- 4 20+/- 4 18+/- 4 12+/- 4
3 21+/- 4 19+/- 4 16+/- 4 10+/- 4
2 20+/- 5 18+/- 5 14+/- 5 8+/- 5
1 19+/- 5 17+/- 5 13+/- 5 7+/- 5
0 18+/- 5 16+/- 5 11+/- 5 6+/- 5
NOTE:
To comply with specific regulatory requirements, certain units may be supplied with
the Power Level parameter set to Low, without the option to change it to High. In
such units the Power Level parameter is not available.