User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
Menus and Parameters
2-37
BreezeACCESS Version 4.3 System Manual
DHCP Client
DHCP Options – Displays the current status of the DHCP
(Dynamic Host Configuration Protocol) support, and allows
selecting a new operation mode. The available options are:
Disable – Use manual procedure for configuring the IP
parameters.
DHCP Only – Search for a DHCP Server and obtain the IP
parameters from it (IP Address, Subnet Mask and Default
Gateway Address).
Automatic – Search for a DHCP Server for configuration of
the IP parameters. If a DHCP Server is not found within
approximately 40 seconds, use the currently configured IP
parameters.
The default is Disable.
Access to DHCP – To define the port through which the unit is
allowed to communicate with a DHCP server. The options are:
From Wlan Only
From Ethernet Only
From Both Ethernet & WLAN
The default for an Access Unit is From Ethernet Only. The
default for a Subscriber Unit is From Wlan Only.
Show IP Parameters – Displays the current values of the IP
Parameters.
Air Interface Parameters (AU and
SU)
Hopping Frequencies Setting Parameters
Hopping Sequence –Displays the Hopping Sequence of the unit.
A hopping sequence is a pre-defined series of channels (frequencies)
that are used in a specific, pseudo-random order as defined in the
sequence. The unit “hops” from frequency to frequency according to
the selected sequence. When more than one AU is co-located in the
same area, it is recommended to assign different hopping sequences
to each AU.
Hopping Sequences are grouped in three hopping sets (see Hopping
Set parameter below). When setting up multiple AUs in the same
site, always choose hopping sequences from the same Hopping Set
to reduce the possibility of collisions on the wireless media. This
NOTE:
The Access to DHCP option is not available in the GU, as this module does
not have a wireless link interface.