User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
Menus and Parameters
2-5
BreezeACCESS Version 4.3 System Manual
The following parameter appears for GPS Modules only:
Unit Status – Indicates the status of the GPS antenna. Either one of
the following messages may be displayed:
UTC is available; date..; time..: This message indicates
that the GPS antenna has synchronized with the satellite system
and that the BS-GU is functioning properly. The message may
include an incorrect time and date, such as a date in 1999. This
indicates that the GPS antenna has not yet synchronized with
the GPS satellites system.
–Or–
UTC time is not available: This message indicates that the
BS-GU is not getting timing signals from the GPS antenna. If the
antenna is functioning and properly connected to the module,
this may be because the antenna has not yet synchronized with
the GPS satellite system.
Show Basic Parameters
The Show Basic Parameters menu displays the current values of the
parameters included in the Basic Configuration menu
(see
Basic Configuration Menu
‚ page 2-13). When using Read-Only
access rights the ESSID parameters (ESSID, Operator ESSID, Run Time
ESSID and Neighboring AU ESSID) and WEP Keys are not displayed.
The display includes some additional useful read-only information such
as the Number of Hopping Frequencies in SU and AU.
Show Advanced Parameters
The Show Advanced Parameters menu enables access sub-menus that
display the current values of the parameters included in the applicable
sub-menus of the Advanced Configuration menu
(see
Advanced Configuration Menu
‚ page 2-36). When using Read-Only
access rights the ESSID parameters (ESSID, Operator ESSID, Run Time
ESSID and Neighboring AU ESSID in Air Interface Parameters), WEP
Keys (Security Parameters) and User Password and Shared Secret
(RADIUS Parameters) are not displayed. The display includes some
additional read-only information such as Number of Hopping
Frequencies (Air Interface Parameters).
Show All Parameters
The Show All Parameters menu displays the current values of all the
parameters included in the Advanced Configuration menu.When using
Read-Only access rights the ESSID parameters (ESSID, Operator
ESSID, Run Time ESSID and Neighboring AU ESSID in Air Interface
Parameters), WEP Keys (Security Parameters) and User Password and
Shared Secret (RADIUS Parameters) are not displayed. The display