BreezeACCESS II Version 4.3 Revision 3.0 June 2003 System Manual Cat. No. 213397 Revision 3.
© 2003 by Alvarion Ltd. All rights reserved. No part of this publication may be reproduced in any material form without the written permission of the copyright owner. Trade Names Alvarion®, BreezeACCESS®, BreezeCOM®, BreezeLINK®, BreezePHONE®, BreezeNET®, WALKair®, WALKnet®, are trade names or trademarks of Alvarion Ltd. Other brand and product names are trade names or trademarks of their respective owners.
BreezeACCESS Version 4.3 System Manual ii (c) ALVARION SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY PURCHASER’S OR ANY THIRD PERSON'S MISUSE, NEGLIGENCE, IMPROPER INSTALLATION OR IMPROPER TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING OR OTHER HAZARD. Limitation Of Liability.
Important Notice iii R&TTE Compliance Statement This equipment complies with the appropriate essential requirements of Article 3 of the R&TTE Directive 1999/5/EC. Safety Considerations For the following safety considerations, “Instrument” means the BreezeACCESS units’ components and their cables. Caution To avoid electrical shock, do not perform any servicing unless you are qualified to do so. BS-GU Lithium Battery Caution: Danger of battery explosion if incorrectly replaced or disposed of.
BreezeACCESS Version 4.3 System Manual iv Important Notice This user manual is delivered subject to the following conditions and restrictions: This manual contains proprietary information belonging to Alvarion Ltd. Such information is supplied solely for the purpose of assisting properly authorized users of the respective Alvarion Ltd. products.
Table of Contents i Table of Contents System Manual Book 1: System Description Introduction ............................................................. 1-1 Introducing BreezeACCESS ..................................................... 1-2 System Components ................................................ 2-1 Subscriber Units (Customer Premises Equipment) ............... 2-2 SU-A/E Units with an Outdoor Radio Unit and Antenna .... 2-2 SU-I/I-D Miniature Indoor Units .....................................
BreezeACCESS 4.3 System Manual ii SU-I/I-D ............................................................................ 3-11 AU-I/I-D ............................................................................ 3-12 SU-R Subscriber Units ..................................................... 3-13 System Manual Book 2: Installation IF-Based Equipment ................................................ 1-1 Modular Base Station Equipment ......................................
Table of Contents Location of the Antenna(s) ................................................. 2-3 Antenna Diversity ............................................................... 2-4 Antenna Polarization .......................................................... 2-4 Antenna Seal ..................................................................... 2-4 Lightning Protection ........................................................... 2-4 Installing SU-R Indoor Units .........................................
BreezeACCESS 4.3 System Manual iv System Manual Book 3: Commissioning Setting Basic Parameters ....................................... 1-1 Accessing the Monitor Program .............................................. 1-2 Accessing the Monitor Program using the RS 232 MON Connector .............................................. 1-2 Accessing the Monitor Program using Telnet .................... 1-3 Operating the Monitor Program .........................................
Table of Contents BS-PS DC Power Supply Module LEDs ............................ 4-5 BS-PS-AC AC Power Supply Module LEDs ...................... 4-5 BS-AU LEDs ...................................................................... 4-6 BS-GU LEDs ...................................................................... 4-6 SU-R LEDs ........................................................................ 4-7 SU-I/SU-I-D LEDs .............................................................. 4-7 AU-I/AU-I-D LEDs ..
BreezeACCESS 4.3 System Manual vi Network Management Parameters (AU, SU and GU) ..... 2-53 Bridge Parameters (AU, SU and GU) .............................. 2-56 Performance Parameters (AU and SU) ........................... 2-69 Service Parameters (AU and SU) .................................... 2-73 RADIUS Parameters Menu (Subscriber Units only) ....... 2-77 Security Parameters (AU and SU) ................................... 2-81 Voice Parameters (Subscriber Units with Voice Support Only) ...............
Table of Contents IP Parameters ................................................................. C-36 System Information Parameters ..................................... C-36 Alarms Parameters ......................................................... C-38 brzPhoneMIB (applicable to SU with voice only) ................ C-39 Dialing Parameters ......................................................... C-39 Voice Parameters ........................................................... C-42 Telephony Signals ...
viii BreezeACCESS 4.
BreezeACCESS II Version 4.3 Revision 3.
System Description Table of Contents Introduction .............................................................1-1 Introducing BreezeACCESS .....................................................1-2 System Components ................................................2-1 Subscriber Units (Customer Premises Equipment) ...............2-2 SU-A/E Units with an Outdoor Radio Unit and Antenna .....2-2 SU-I/I-D Miniature Indoor Units ..........................................2-4 SU-R High-Power Indoor Units ..........
ii BreezeACCESS Version 4.3 System Description SU-R Subscriber Units .....................................................
Chapter 1 Introduction About This Chapter This chapter introduces the BreezeACCESS system, its components and its functions.
BreezeACCESS Version 4.3 System Description 1-2 Introducing BreezeACCESS BreezeACCESS IP Broadband Wireless Access system is an IP based access system that supports wireless data and voice services, employing wireless packet-switched data technology to support high-speed IP services, including fast access to the Internet and Virtual Private Networks.
Chapter 2 System Components About This Chapter This chapter describes BreezeACCESS system components. It includes the following sections: Subscriber Units (Customer Premises Equipment)‚ page 2-2, describes BreezeACCESS equipment installed at the customer’s premises. Base Station Equipment‚ page 2-6, describes the equipment used in BreezeACCESS Base Stations.
BreezeACCESS Version 4.3 System Description 2-2 Subscriber Units (Customer Premises Equipment) The BreezeACCESS Subscriber Unit (SU) installed at the customer premises provides data only or data and telephone connections. The data connection is a standard IEEE 802.3 Ethernet 10BaseT (RJ 45) interface while the voice connection (in units that support voice) is a standard RJ 11 Plain Old Telephone (POTS) interface.
System Components 2-3 Figure 2-1: BreezeACCESS SU-A/E Outdoor and Indoor Units BreezeACCESS II SU-A/E units are available with several different levels of output power at the antenna port: 26 dBm (HP) 15 dBm (GP) 7 dBm (MP) 4 dBm (LP) The following products are available: Data-only Units: SU-X-1D-2.4-YP The unit supports one Ethernet device. SU-X-BD-2.4-YP The unit provides bridge functionality and can support up to a full LAN. Data and Voice Units: SU-X-1D1V-2.
BreezeACCESS Version 4.3 System Description 2-4 X=A: The outdoor radio unit includes an integral high gain flat antenna X=E: The outdoor radio unit has a connector for an external antenna. Y=H: HP model. The maximum output power at the antenna port is 26 dBm Y=G: GP model. The maximum output power at the antenna port is 15 dBm Y=M: MP model. The maximum output power at the antenna port is 7 dBm Y=L: LP model.
System Components 2-5 The following types of units are available: Data-only Units: SU-X-1D-2.4 The unit supports one Ethernet device SU-X-BD-2.4 The unit provides bridge functionality and can support up to a full LAN Data and Voice Units: SU-X-1D1V-2.4 The unit supports one Ethernet device and has an interface to a standard analog telephone set (POTS). SU-X-BD1V- The unit provides bridge functionality and can support a full LAN. It also has an interface for a standard analog telephone (POTS).
BreezeACCESS Version 4.3 System Description 2-6 SU-R High-Power Indoor Units The SU-R line includes small-footprint, high-power units that are designed for indoor desktop or wall-mount installations. SU-R units are available with three different antenna configurations: Two clip-on omni antennas. A wall mountable antenna. An outdoor high-gain antenna. Figure 2-3: BreezeACCESS SU-R Unit The following types of units are available: Data-only Units: SU-R-1D The unit supports one Ethernet device.
System Components 2-7 Standalone “Micro-Cell” Access Unit AU-I/I-D miniature indoor units Modular Base Station Equipment The Base Station equipment is based on the BS-SH 3U chassis, which is suitable for installation in 19” racks. The chassis contains one or two power supply modules, up to six active Access Unit Network Interface (BS-AU) modules and an optional BS-GU GPS and Alarms module.
BreezeACCESS Version 4.
System Components 2-9 Figure 2-5: BreezeACCESS GU-A-BS System Components The BreezeACCESS BS-GU module is designed to be inserted into the BS-SH 19” base station chassis to provide hopping synchronization signals to the BS-AU Access Unit modules. The card uses timing signals derived from signals received from the GU-RA GPS antenna. These signals, generated by the GPS global satellites network, allow accurate synchronization of systems located in different locations.
BreezeACCESS Version 4.3 System Description 2-10 Daisy-chained BS-GU modules use the synchronization signals generated by the first module in the chain (the Master module. The BS-GU module also supports the management of alarm inputs and outputs. The module receives Alarms In indications from other BreezeACCESS modules in the base station shelf (internal alarms) and external alarms from other devices via the AL IN connector.
System Components 2-11 AU-I/I-D Miniature Indoor Units The AU-I/I-D line includes miniature units that are designed for indoor desktop or wall-mount installations and comprise a single unit that is powered from the mains (100-250 VAC). The AU-I products include two integral 2 dBi omni antennas. The AU-I-D products have two RF connectors for detached diversity antennas. Figure 2-7: BreezeACCESS AU-I-D Unit BreezeACCESS Version 4.
BreezeACCESS Version 4.3 System Description 2-12 Networking Equipment The base station equipment is connected to the backbone through standard data communication and telecommunication equipment. For improved security, the 10BaseT ports of the AU modules are connected directly to a multi-port router. This router is connected by any means of point-to-point link to the backbone.
System Components 2-13 BreezeMANAGE Alvarion’s SNMP-based BreezeMANAGE network management application provides a powerful tool for configuring, controlling, monitoring and effectively managing BreezeACCESS networks from a single, central network management station. BreezeMANAGE, together with the powerful tools available through its use under leading network management platforms, provides numerous benefits to operators of BreezeACCESS networks.
BreezeACCESS Version 4.3 System Description 2-14 BreezeCONFIG The BreezeCONFIG ACCESS configuration utility can also be used to manage BreezeACCESS system components. It is an SNMP-based application that provides a consistent view of the network and the system administrator can use it to control a large number of units from a single location.
Chapter 3 Specifications About This Chapter This chapter lists the technical specifications of BreezeACCESS and includes the following sections: System Specifications‚ page 3-2, outlines the technical specifications of the BreezeACCESS system. Physical Specifications‚ page 3-7, lists the physical and electical specifications for different types of BreezeACCESS units.
BreezeACCESS Version 4.3 System Description 3-2 System Specifications Radio and Modem Parameter Value Frequency 2.400-2.500 GHz (according to country standard) Operation Mode Time Division Duplex Radio Access Method FH-CDMA Standard Compliance FCC Part 15.
Specifications 3-3 BreezeACCESS II Radio Regulatory Standards The systems support different “country standards” for compliance with the applicable local radio regulations. The country standards are configured at the factory. The country standards determine the following: a: Hopping frequency band and hopping sequences b: Support of synchronization among Access Units (AU-A/E-BS units). In some countries such synchronization is not permitted.
BreezeACCESS Version 4.3 System Description 3-4 Voice/Fax (Subscriber Units with voice support) Parameter Value Standard Compliance ITU-T H.323 Ver. 2 VoIP standard Compression G.711 (A-Law and µ-Law) - 64 Kbps (transparent) G.723.1 - 6.3 Kbps G.729 - 8 Kbps (G.729, G.729 with Annex A and/or Annex B) Silence Compression G.723.1 - Voice Activity Detection (VAD), G.729 - Annex B Echo Cancellation ITU-T G.168 and G.131 Fax Transmission According to T.
Specifications 3-5 Configuration and Management Parameter Value Management Options a. Via the MON port, using terminal emulation with the built-in monitor program b. Telnet, using the monitor program c. TFTP, using the Configuration upload/download utility d. SNMP Remote Management Access From Wired LAN, Wireless Link Management Access Protection a. Multilevel password b. Configuration of remote access direction (from Ethernet only, from wireless link only or from both sides) c.
BreezeACCESS Version 4.3 System Description 3-6 Environmental Parameter Unit Value Operating Temperature Outdoor Units -400C to 550C (GU-RA: -400C to 850C) Indoor equipment 00C to 400C Operating Humidity Outdoor Units 5%-95% non-condensing, weather protected Indoor equipment 5%-95% non-condensing Standards Compliance, General Type Standard EMC FCC part 15.247, EN 300 826 Safety UL 1950, EN 60950 Environmental ETS 300 019 part 2-3 class 3.
Specifications 3-7 Physical Specifications SU-A/E Subscriber Unit Connectors Unit Connector SU-NI SU-RE SU-RA Description IF TNC jack, 50 ohm, lightning protected ETH 10BaseT Ethernet (RJ 45) with 2 embedded LEDs.
BreezeACCESS Version 4.
Specifications 3-9 Modular Base Station Equipment Connectors Unit AU-A/E-BS Connector AU-BS Description IF TNC jack, 50 ohm, lightning protected ETH 10BaseT Ethernet (RJ 45) with 2 embedded LEDs Cable connection to a PC: crossed MON RS 232, 3-pin low profile jack IF TNC jack, 50 ohm, lightning protected ANT N-Type jack, 50 ohm, lightning protected IF TNC jack, 50 ohm, lightning protected BS-PS -48V 3 pin DC power plug BS-PS-AC AC IN 3 pin AC power plug BS-GU ETH 10BaseT Ethernet (RJ
Specifications 3-11 SU-I/I-D Connectors Connector Description Antenna (SU-I-D) 2 x SMA jacks, 50 ohm ETH 10Base-T Ethernet (RJ-45) with 2 embedded LEDs.
BreezeACCESS Version 4.3 System Description 3-12 AU-I/I-D Connectors Connector Description Antenna (AU-I-D) 2 x SMA jacks, 50 ohm ETH 10Base-T (RJ-45) with 2 embedded LEDs. Cable connection to a PC: crossed DC IN 5V Standard DC phone jack to external power supply MON RS 232, 3-pin low profile jack Electrical Unit AU-I/I-D Details Power consumption: External power supply AC input power: 100-240Vr.m.s., 47-63 Hz DC power output: 5.1V, 2A max.
Specifications 3-13 SU-R Subscriber Units Connectors Connector Description Antenna 2 proprietary jacks, 50 ohm (with special SMA adapters if needed) ETH 10BaseT Ethernet (RJ 45) with 2 embedded LEDs Cable connection to a PC: straight TEL (units with voice support) RJ 11 jack (POTS) DC IN Standard DC phone jack to external power supply MON RS 232, 3-pin low profile jack Electrical Unit All SU-R units Details External power supply AC input power: 100-240 Vr.m.s.
3-14 Manual Revision: 3.0 BreezeACCESS Version 4.
BreezeACCESS II Version 4.3 Revision 3.
Installation Table of Contents IF-Based Equipment .................................................1-1 Modular Base Station Equipment .......................................1-2 Standalone AU-A/E-NI Access Unit ...................................1-3 Other Items Required for Installation ..................................1-3 Guidelines for Selection of Equipment Locations ..................1-5 AU-RA and AU-RE .............................................................1-5 SU-RA and SU-RE ....................
ii BreezeACCESS Version 4.3 Installation Antenna Seal ..................................................................... 2-4 Lightning Protection ........................................................... 2-4 Installing SU-R Indoor Units ..................................................... 2-5 Wall Mounting the Unit ....................................................... 2-5 Connecting the Omni Antennas ......................................... 2-6 Connecting a Detached Antenna ......................
Chapter 1 IF-Based Equipment About This Chapter This chapter describes the basic installation of BreezeACCESS IF-based equipment, including SU-A/E subscriber units, modular base station equipment and stand-alone AU-A/E-NI access units. It includes the following sections: Packing Lists‚ page 1-2, lists the equipment that is packed with each BreezeACCESS IF-based unit.
BreezeACCESS Version 4.
BreezeACCESS Version 4.
IF Based Equipment 1-5 Guidelines for Selection of Equipment Locations NOTE: Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void the BreezeACCESS product warranty and may expose the end user or the service provider to legal and financial liabilities.
BreezeACCESS Version 4.3 Installation 1-6 IF Cable The outdoor unit is connected to the indoor unit by means of an IF cable carrying signaling, control signals and power. The IF frequency is 440 MHz. The maximum allowed attenuation of the IF cable connecting the outdoor unit to the indoor unit is 15 dB at 440 MHz, and the maximum allowed DC resistance (the sum of the DC resistance of the inner and outer conductors) is 1.5 ohm. This allows for cable length of up to 30 m when using the standard RG 58 cable.
IF Based Equipment 1-7 Installing the Outdoor Unit NOTE: Outdoor units must be installed by a professional installer only. The Outdoor Unit Bottom Panel The SU-RA and AU-RA outdoor units include the radio and an integral high-gain flat antenna located on the front of the unit. The SU-RE and AU-RE outdoor radio units have an RF connector for connection to an external antenna.
BreezeACCESS Version 4.
IF Based Equipment 1-9 Pole Mounting the Outdoor Unit The outdoor unit can be secured to the pole using one of the following options: Special brackets and open-ended bolts (supplied with each unit). There are two pairs of threaded holes on the back of the unit, allowing use of the special brackets with various pole widths. Metal bands (9/16" wide, minimum 12" long). Figure 1-3‚ page 1-10 shows the locations of the band grooves and threaded holes on the rear side of the outdoor unit.
BreezeACCESS Version 4.3 Installation 1-10 Figure 1-3: Grooves/Threaded Holes Figure 1-4: 3" Pole Mounting Installation Using the Special Brackets NOTE: When inserting the open-ended bolts, make sure to insert them with the grooves pointing outwards; these grooves are intended to allow fastening of the bolts with a screwdriver. Manual Revision: 3.
IF Based Equipment 1-11 The integral antenna of the AU-RA is relatively long. The top of the antenna should also be secured to the pole, as shown in Figure 1-5:. Figure 1-5:: Pole Mounting the AU-RA Figure 1-6:: Pole Mounting the AU-RA (Top View) NOTE: The top of the AU-RA antenna must be secured to the pole only in order to keep it from moving due to strong winds or other adverse conditions. Do not over tighten the screws in order to avoid damaging the antenna. BreezeACCESS Version 4.
IF Based Equipment 1-13 Installing the SU-NI and AU-NI Indoor Unit Figure 1-7: SU-NI with Voice Support Rear Panel Figure 1-8: SU-NI/AU-NI Front Panel NOTE: The rear panel pictured above in Figure 1-7 is a SU-NI with voice support; AU-NI units and SU-NI units that belong to Subscriber Units without voice support are identical, except that they have no TEL port.
BreezeACCESS Version 4.3 Installation 1-14 The SU-NI/AU-NI provides the following interfaces: An Ethernet connector (marked ETH) for connecting the unit to the network. See Table 1-1‚ page 1-4 for information on the required type of Ethernet cable. An IF connector for connecting the unit to an outdoor unit. A DC-12V connector for the power supply. A MON connector for connecting an ASCII terminal with terminal emulation software for configuration and maintenance purposes.
IF Based Equipment 1-15 Installing Modular Base Station Equipment BS-SH Slot Assignments The base station chassis has ten slots. Figure 1-9: BS-SH Chassis Slot Assignments The two wide slots on both sides of the shelf accommodate the BS-PS or BS-PS-AC power supply modules. The shelf is designed to support power supply redundancy through the use of two power supply modules. If a single power supply is used, it can be inserted in any of the two available slots.
BreezeACCESS Version 4.3 Installation 1-16 The BS-PS The BS-PS provides power to all the modules installed in the BS-SH chassis. The BS-PS front panel is shown in Figure 1-10‚ page 1-16. Figure 1-10: BS-PS Front Panel The BS-PS provides a power input connector (marked -48V) for connecting the -48VDC power source to the module. The color codes of the cable wires are: Black Red -48 VDC + (Return) The power switch turns the mains power to the power supply ON and OFF.
IF Based Equipment 1-17 The BS-PS-AC The BS-PS-AC is an AC to DC converter that provides power to all the modules installed in the BS-SH chassis. The BS-PS-AC front panel is shown in Figure 1-11‚ page 1-17. Figure 1-11: BS-PS-AC Front Panel The BS-PS-AC provides a power input connector (marked AC IN) for connecting the AC power cable to the mains. The ON/OFF power switch controls the connection of the mains power to an AC to DC converter. Table 1-8: BS-PS-AC LEDs LED Description 3.3V Green LED.
BreezeACCESS Version 4.3 Installation 1-18 WARNING: If two power supply modules are used in the same chassis for redundancy, both power supplies must be of the same type. Do not use a mix of AC and DC power supply modules in the same chassis. The BS-AU Figure 1-12: BS-AU Front Panel Table 1-9: BS-AU LEDs Name Description Functionality PWR Power supply 12 VDC On – After successful power up, indicating that 12 VDC is supplied to the outdoor unit.
IF Based Equipment 1-19 The BS-AU provides the following interfaces: An Ethernet connector (marked ETH) for connecting the BS-AU to the network. A straight Ethernet cable should be used to connect the module to a hub, router or switch. An IF connector for connecting the BS-AU to an outdoor unit (AU-RE or AU-RA). A MON connector for connecting an ASCII terminal with terminal emulation software for configuration and maintenance purposes.
BreezeACCESS Version 4.3 Installation 1-20 power source and the black wire to the -48 VDC contact of the power source. Connect the red wire to the + (Return) contact. Connect the shield to the ground. 6. If a BS-PS-AC AC power supply is used, connect the AC power cable to the AC jack (marked AC IN) located on the front panel of the BS-PS-AC power supply. If a redundant power supply module is installed, connect a power cable to that unit as well. Connect the power cable(s) to the AC mains. 7.
IF Based Equipment 1-21 Installing the GU-A-BS GPS and Alarms System BS-GU Front Panel Figure 1-13: BS-GU Front Panel BreezeACCESS Version 4.
BreezeACCESS Version 4.3 Installation 1-22 Table 1-10: BS-GU Connectors Connector Name Functionality SYNC IN Receives signals from the GPS antenna unit. If more than one collocated BS-GU module is daisy-chained, this connector is used by a “Slave” module to receive signals from the “Master” module’s SYNC OUT connector. SYNC OUT Transfers the signals received on the SYNC IN port.
IF Based Equipment 1-23 Installing the GU-RA GPS Antenna 1. Screw the GPS antenna firmly to the special 1” threaded pole. 2. Use the mounting kit supplied with the unit (or any other suitable means) to secure the GPS antenna pole to an existing pole (e.g. any pole used for mounting base station antennas or the outdoor units of the BreezeACCESS Access Units). Choose the location to ensure an obstacle-free line of sight from the GPS antenna to the sky, extending at least 30 degrees in all directions.
BreezeACCESS Version 4.3 Installation 1-24 4. Connect the 12-pin round connector to the GPS antenna. 5. Route the cable to the location intended for installation of the BS-GU module. NOTE: Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities.
Chapter 2 Indoor SU-R Units About This Chapter This chapter explains how to install BreezeACCESS SU-R units and includes the following sections: Packing Lists‚ page 2-2, lists the equipment that is packed with each BreezeACCESS SU-R unit. Installation Guidelines‚ page 2-3, gives general tips and instructions for installing BreezeACCESS SU-R units. Installing SU-R Indoor Units‚ page 2-5, outlines the installation procedures for SU-R units.
BreezeACCESS Version 4.3 Installation 2-2 Packing Lists SU-R Subscriber Unit The SU-R units are shipped with the following units and accessories. The exact packing list varies depending on system configuration and ordered equipment.
Indoor SU-R Units 2-3 Table 2-1: Required Type of Ethernet Cable Unit Type SU-R Subscriber Unit Connection to a PC Connection to a Hub Straight Crossed Installation Guidelines This section describes the installation guidelines and the various considerations that must be taken into account when planning the installation. Location of the Unit The unit can be placed on a desktop or a shelf, or can be attached to a wall.
BreezeACCESS Version 4.3 Installation 2-4 Position the antennas clear of metal furniture and away from moving metal objects such as metal fans or doors. Antenna Diversity Multipath propagation is to be expected when there are potential reflectors between the Access Unit and Subscriber Units. These reflectors may be buildings or moving objects such as airplanes and motor vehicles.
Indoor SU-R Units 2-5 Lightning protection entails connecting an antenna discharge unit (also called an arrestor) to each cable as close as possible to the point where it enters the building. It also entails proper grounding of the arrestors and of the antenna mast (if the antenna is connected to one). The lightning arrestor should be installed and grounded at the point where the cable enters the building. The arrestor is connected to the unit at one end and to the antenna at the other end.
BreezeACCESS Version 4.3 Installation 2-6 Connecting the Omni Antennas 1. Connect the omni antennas to antenna ports 1 and/or 2 on the sides of the unit. Push each antenna connection carefully into a port with the antenna facing downward and carefully turn the antenna upward to firmly lock it. 2. Extend the antennas upward vertically in relation to the floor to achieve vertical polarization. Connecting a Detached Antenna 1. Connect the special adapter to antenna port 1 (marked 1) on the side of the unit.
Indoor SU-R Units 2-7 1. Plug the output jack of the power transformer into the DC input jack (marked DC IN) located on the bottom panel of the unit. 2. Connect the supplied universal power transformer to a power outlet -110/ 220VAC. 3. Use a straight Ethernet 10BaseT cable to connect the Ethernet port (marked ETH) to a PC or to a hub’s uplink port. Use a crossed Ethernet10BaseT cable to connect to a hub. 4.
2-8 Manual Revision: 3.0 BreezeACCESS Version 4.
Chapter 3 Indoor SU-I and AU-I Units About This Chapter This chapter explains how to install BreezeACCESS SU-I and AU-I units and includes the following sections: Packing Lists‚ page 3-2, lists the equipment that is packed with each BreezeACCESS SU-I and AU-I units. Installation Guidelines‚ page 3-4, give general tips and instructions for installing BreezeACCESS SU-I and AU-I units. Installing SU-I/I-D and AU-I/I-D Units‚ page 3-7, outlines the installation procedures for SU-I and AU-I units.
BreezeACCESS Version 4.
Indoor SU-R Units 3-3 For local configuration of parameters: A portable PC with Terminal Emulation software and Monitor cable* (Monitor cable is supplied with Access Units) –Or– A portable PC equipped with an Ethernet card, Telnet software and an Ethernet cable (see Table 3-1‚ page 3-3) Items marked with an asterisk (*) are available as options from Alvarion.
BreezeACCESS Version 4.3 Installation 3-4 Installation Guidelines This section describes the installation guidelines and the various considerations that must be taken into account when planning the installation. Location of the Unit The unit can be placed on a desktop or a shelf, or can be attached to a wall. The unit should be installed as near as possible to the antenna (models with detached antenna).
Indoor SU-R Units 3-5 capabilities. By using two antennas per unit, the system can select the best antenna on a per-packet basis (every several milliseconds). When installing a single antenna, configure the Transmit Antenna option to either Antenna 1 or Antenna 2, according to the antenna being used. When using two antennas, configure the Transmit Antenna option to Both Antennas. Antenna Polarization Antenna polarization must be the same at either end of the link.
BreezeACCESS Version 4.3 Installation 3-6 NOTE: Detached outdoors antennas should be installed ONLY by experienced antenna installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void the BreezeACCESS Product Warranty and may expose the end user to legal and financial liabilities.
Indoor SU-R Units 3-7 Installing SU-I/I-D and AU-I/I-D Units Connectors and LEDs The unit provides the following interfaces: Figure 3-1: SU-I Rear Panel An Ethernet connector (marked ETH) for connecting the unit to the network. See Table 3-1‚ page 3-3 for information on the required type of Ethernet cable. A TEL connector (Subscriber Units with voice support only) for connecting a regular telephone. Figure 3-2:: SU-I/AU-I Side View A DC-IN 5V connector for the power transformer.
BreezeACCESS Version 4.
Indoor SU-R Units 3-9 Figure 3-4:: AU-I Front Panel Table 3-3: AU-I LEDs Name Description Functionality POWER Power supply On – After successful power up Off – Power off WIRELESS LINK Wireless Link Activity Blinking – Receiving packets from the wireless link Off – no reception of packets from the wireless link LOAD Number of active subscriber units No subscribers 1-8 subscribers 9-16 subscribers 17 or more subscribers Wall Mounting the Unit Use the supplied brackets for wall mounting to in
BreezeACCESS Version 4.3 Installation 3-10 1. Turn the unit so the rear panel is facing you. 2. Unscrew the two screws located at the antennas end of the unit (the top screws). 3. Align the Unit Mounting Slots (see Figure 3-6) with the slots you have just unscrewed. 4. Using the longer screws supplied with the wall mounts, screw the wall mount to the unit. 5.
Indoor SU-R Units 3-11 Connecting Antenna(s) to the Units For installation convenience, a torque key is included with all BreezeACCESS SU-ID and AU-ID units. WARNING: The use of improper tools for tightening antenna connection cables to BreezeACCESS units may result in damage to the cable connectors. Use the included torque key to tighten the cable(s) to the connector(s) on the side of the unit. The key is designed to prevent over tightening of the screws and protects the connectors from damage.
BreezeACCESS Version 4.3 Installation 3-12 1. Plug the output jack of the power transformer into the DC input jack (marked DC IN 5V) located on the side of the unit. 2. Connect the power transformer to a power outlet - 110/ 220VAC. 3. Use an Ethernet 10BaseT cable to connect a PC or a hub to the Ethernet port located on the rear panel of the unit. See Table 3-1‚ page 3-3 for details on the required type of the Ethernet cable. 4.
BreezeACCESS II Version 4.3 Revision 3.
Commissioning Table of Contents Setting Basic Parameters .......................................1-1 Accessing the Monitor Program ..............................................1-2 Accessing the Monitor Program using the RS 232 MON Connector ..............................................1-2 Accessing the Monitor Program using Telnet .....................1-3 Operating the Monitor Program ..........................................1-4 Configuring Basic Parameters in Access and Subscriber Units .................
ii BreezeACCESS Version 4.3 Commissioning AU-RA/RE Outdoor Units LEDs ......................................... 4-4 SU-NI and AU-NI Indoor Units LEDs ................................. 4-5 BS-PS DC Power Supply Module LEDs ............................ 4-5 BS-PS-AC AC Power Supply Module LEDs ...................... 4-5 BS-AU LEDs ...................................................................... 4-6 BS-GU LEDs ...................................................................... 4-6 SU-R LEDs .........
Chapter 1 Setting Basic Parameters About This Chapter This chapter explains how to configure the basic parameters of the BreezeACCESS system and includes the following section: Accessing the Monitor Program‚ page 1-2, explains how to accessyour BreezeACCESS units for configuration. Configuring Basic Parameters in Access and Subscriber Units‚ page 1-5, outlines the basic configuration process for BreezeACCESS AU and SUs.
BreezeACCESS Version 4.3 Commissioning 1-2 Accessing the Monitor Program Accessing the Monitor Program using the RS 232 MON Connector 1. Use the monitor cable to connect the MON connector of the unit to the COM port of your ASCII ANSI terminal or PC. The COM port connector on the monitor cable is a 9-pin D-type plug. 2. Run a terminal emulation program (such as HyperTerminal™). 3.
Setting Basic Parameters 1-3 BreezeACCESS/AU-BS Official Release Version – 4.0.40 Release Date: Thu Dec 20 20:21:36 2001 Main Menu ===================== 1 – Info Screens 2 – Unit Control 3 – Basic Configuration 4 – Site Survey 5 – Advanced Configuration X – Exit >>> Figure 1-1: Main Menu – Administrator Access Rights (SU and AU) The appearance of the Main Menu varies in accordance with the set access level. For users with Read Only access rights, only the Info Screens option is displayed.
BreezeACCESS Version 4.3 Commissioning 1-4 Table 1-2: Required Type of Ethernet Cable Unit Type Connection to a PC Connection to a Hub All SU-R Units and Subscriber Units that support a single Ethernet device (SU-1D, SU-1D1V) Straight NA Subscriber Units (excluding SU-R Units) that support multiple Ethernet devices (SU-BD, SU-BD1V) Crossed Straight Access Units Crossed Straight GPS module Straight Crossed 2. The Select Access Level menu appears.
Setting Basic Parameters 1-5 Configuring Basic Parameters in Access and Subscriber Units The Basic Configuration menu in the Monitor program includes all the parameters necessary for the initial operation of BreezeACCESS Subscriber and Access Units. In many installations, most of these parameters should not be changed from their default values.
BreezeACCESS Version 4.
Setting Basic Parameters 1-7 Refer to Book 4: Operation and Administration for detailed information on the applicable parameters. In many installations, most of these parameters should not be changed from their default values. The following list includes the basic parameters and their default values: Table 1-5: GU-A-BS Units Basic Parameters Parameter Default Value IP Address 10.0.0.1 Subnet Mask 255.0.0.0 Default Gateway Address 0.0.0.
1-8 Manual Revision: 3.0 BreezeACCESS Version 4.
Chapter 2 Optimizing the Wireless Link About This Chapter This chapter explains how to optimize the performance of the wireless link of BreezeACCESS Subscriber Units and includes the following sections: Configuring the Maximum Data Rate (Subscriber Units)‚ page 2-2, explains how to read the RSSI measurement and to configure the optimum value for the Maximum Data Rate parameter.
BreezeACCESS Version 4.3 Commissioning 2-2 Configuring the Maximum Data Rate (Subscriber Units) The BreezeACCESS units transmit at data rates of 3 Mbps, 2 Mbps and 1Mbps. If the quality of the link is not sufficient, it is recommended to decrease the value of the Maximum Data Rate. Note that the higher the data rate, the higher the error rate. Before reaching a decision on the optimum value for the Maximum Data rate for a specific SU, it is recommended to acquire the RSSI results from the AU.
Optimizing the Wireless Link 2-3 Aligning the Antenna of the SU-A/E Subscriber Unit NOTE: Antenna alignment using the RSSI bar display is possible only after the Access Unit you wish to associate with is operational and the basic parameters in the Subscriber Unit were properly configured. Otherwise, the unit will not be able to synchronize and associate with the Access Unit.
BreezeACCESS Version 4.3 Commissioning 2-4 Configuring the Transmit Power of the AU-RE The transmitted output power of the AU should be adjusted in the following cases: If there is a need to cover a relatively small area and to minimize the interference with the operation of neighboring cells. According to the FCC rules 15.247 (3), when operating the equipment in a multi-point system, the RF output power must be adjusted according to the gain of the antenna to limit the EIRP to a maximum of 36 dBm.
Optimizing the Wireless Link 2-5 Positioning the SU-I or SU-R Subscriber Unit with Omni Antennas for Optimal Operation To identify the best location for the unit you can either use the signal quality LED indicators on the front panel of the unit or view the Received Signal Strength Indication (RSSI) on the monitor. In most installations, alignment using the LEDs is sufficient.
BreezeACCESS Version 4.3 Commissioning 2-6 Aligning the External Antenna of SU-R and SU-I-D Units For Subscriber Units with directional antenna(s), you can either use the signal quality LED indicators on the front panel of the unit or view the Received Signal Strength Indication (RSSI) on the monitor. In most installations, alignment using the LEDs is sufficient. The RSSI reading (see para Configuring the Maximum Data Rate (Subscriber Units)‚ page 2-2) can be used when finer alignment is required.
Chapter 3 BS-GU Connectors About This Chapter This chapter explains how to connect external devices to the AL IN and AL OUT connectors of the BS-GU module. It also includes a description of the cable connecting the BS-GU to the GPS antenna and of the SYNC IN/SYNC OUT connectors’ pin assignments.
BreezeACCESS Version 4.3 Commissioning 3-2 Connecting External Devices to the BS-GU AL IN and/or AL OUT Connectors Open-ended cables are available from the company for connecting to the module external alarm inputs through the AL IN connector and/or activating external devices through the AL OUT connector. See the tables that follow for descriptions of the connectors’ pins functionality. For details on defining and using the alarm inputs and output, refer to Book 4: Operation and Administration.
Connecting External Alarm Devices 3-3 Alarms Out Cable Table 3-2: Alarms Out Cable 9-pin Micro D-Type AL OUT Connector Description Color Code 1 Relay 1 Common Brown 2 Relay 1 Normally Closed White 3 Relay 2 Common Green 4 Relay 3 Common Red 5 Relay 3 Normally Closed Black 6 Relay 1 Normally Open Purple 7 Relay 2 Normally Closed Yellow 8 Relay 2 Normally Open Orange 9 Relay 3 Normally Open Blue NOTE: The other side of the cable is supplied open-ended.
BreezeACCESS Version 4.3 Commissioning 3-4 NOTE: *Descriptions are with respect to the BS-GU SYNC IN connector side. Figure 3-1 shows a 9-pin Micro D-Type Connector (cable side), and Figure 3-2 shows a 12-pin round connector. 9-pin Micro D-Type connector Figure 3-1: 9-pin Micro D-Type Connector (cable side) 1 9 5 Figure 3-2: 12-pin Round Connector Manual Revision: 3.
Connecting External Alarm Devices 3-5 SYNC Cable Cable Type: EIA RS-422 3X2X25AWG +1X2X24 AWG FTP Shielded cable. Table 3-4: SYNC Cable 9-pin Micro D-Type SYNC OUT Connector Description Color Code 9-pin Micro D-Type SYNC-IN Connector 1 GPS TX+/SYNC D+ Black 1 2 GPS TX-/SYNC D- Brown 2 5 1PPS+/SYNC S+ Red 5 6 1PPS-/SYNC S- Orange 6 8 DC GPS Green 8 9 Slave Yellow 9 3,4,7 Not connected 3,4,7 NOTE: * Descriptions are with respect to the SYNC OUT connector side.
3-6 Manual Revision: 3.0 BreezeACCESS Version 4.
Chapter 4 Verifying Proper Operation About This Chapter This chapter explains how to confirm that the BreezeACCESS system is functioning properly and includes the following sections: Verifying Connectivity ‚ page 4-2 , explains how to ensure that your BreezeACCESS and the equipment connected to them are operating properly. LED Indicators ‚ page 4-4 , lists the LEDs found on BreezeACCESS units and their meanings.
4-2
Verifying Proper Operation 4-3 Verifying Proper Operation of the GU-A-BS GPS Unit NOTE: It may take up to 10 minutes from the time the GU-RA GPS antenna is powered up until it is fully synchronized with the GPS satellite system. When the unit is operating properly, the PWR and OK green LEDS should be on, indicating that the BS-GU module is supplying power to the GU-RA GPS antenna and that the GPS antenna is functioning properly.
BreezeACCESS Version 4.
Verifying Proper Operation 4-5 SU-NI and AU-NI Indoor Units LEDs Table 4-3: SU-NI and AU-NI Indoor Units LEDs Name Description Functionality PWR Power supply On – After successful power up, indicating that 12 VDC is supplied to the outdoor unit.
BreezeACCESS Version 4.3 Commissioning 4-6 BS-AU LEDs Table 4-6: BS-AU LEDs Name Description Functionality PWR Power supply 12 VDC On – After successful power up, indicating that 12 VDC is supplied to the outdoor unit.
Verifying Proper Operation 4-7 SU-R LEDs Table 4-8: SU-R LEDs Name Description PWR Power supply SIGNAL QUALITY Quality of received RF signal Functionality On – After successful power up Off – Power off Very low quality reception or not synchronized with Access Unit. Low quality reception (usually enabling 1Mbps traffic). Medium quality reception (usually enabling 2 Mbps traffic). High quality reception (usually enabling 3 Mbps traffic).
BreezeACCESS Version 4.3 Commissioning 4-8 AU-I/AU-I-D LEDs Table 4-10: AU-I/AU-I-D LEDs Name Description Functionality POWER Power supply On – After successful power up Off – Power off WIRELESS LINK Wireless Link Activity Blinking – Receiving packets from the wireless link Off – no reception of packets from the wireless link LOAD Number of active subscriber units No subscribers 1-8 subscribers 9-16 subscribers 17 or more subscribers Manual Revision: 3.
BreezeACCESS II Version 4.3 Revision 3.
Operations and Administration Table of Contents Accessing the Monitor Program ..............................1-1 Accessing the Monitor Program using the RS 232 MON Connector ......................................................1-2 Accessing the Monitor Program using Telnet ........................1-3 Operating the Monitor Program ...............................................1-4 Menus and Parameters ............................................2-1 Main Menu .................................................
ii BreezeACCESS Version 4.3 Operations and Administration Service Parameters (AU and SU) .................................... 2-73 RADIUS Parameters Menu (Subscriber Units only) ....... 2-77 Security Parameters (AU and SU) ................................... 2-81 Voice Parameters (Subscriber Units with Voice Support Only) ................................................ 2-83 Dialing Parameters (Subscriber Units with Voice Support Only) ................................................
Chapter 1 Accessing the Monitor Program About This Chapter This chapter explains how to access the monitor program. It also describes how to use the monitor program to set up, configure, and manage BreezeACCESS Broadband Wireless Access system units. This includes the Subscriber Units (SUs), Access Units (AUs) and GPS and Alarms modules (GUs).
BreezeACCESS Version 4.3 Operations and Administration 1-2 Accessing the Monitor Program using the RS 232 MON Connector 1. Use the monitor cable to connect the MON connector of the unit to the COM port of your ASCII ANSI terminal or PC. The COM port connector on the monitor cable is a 9-pin D-type plug. NOTE: The GU-BS GPS and Alarms module does not have an external MON port.
Accessing the Monitor Program 1-3 Accessing the Monitor Program using Telnet 1. Connect a PC to the Ethernet port of the unit. See the table below to determine the type of cable. Configure the PC’s IP parameters to enable connectivity with the unit (the default IP Address is 10.0.0.1). Run the Telnet application.
BreezeACCESS Version 4.3 Operations and Administration 1-4 Screens option is displayed. Users with this access level cannot access the Unit Control, Basic Configuration, Site Survey and Advanced Configuration menus. For users with Installer access rights, the first four menu items (Info Screens , Unit Control, Basic Configuration and Site Survey) are displayed. Users with this access level cannot access the Advanced Configuration menu.
Chapter 2 Menus and Parameters About This Chapter This chapter describes the BreezeACCESS configuration menus and parameters. It includes the following sections: Main Menu‚ page 2-2. Info Screens Menu‚ page 2-3. Unit Control Menu‚ page 2-6. Basic Configuration Menu‚ page 2-13. Site Survey Menu‚ page 2-15. Advanced Configuration Menu‚ page 2-36.
BreezeACCESS Version 4.3 Operations and Administration 2-2 Main Menu From the Main Menu you can access the following menus, depending on your access level: Info Screens – Provides read-only display of current parameter values. Available at all access levels. Unit Control – Enables access to general operations such as resetting the unit, loading the default parameters, changing passwords and switching between software versions. Available at the Installer and Administrator access levels.
Menus and Parameters 2-3 Info Screens Menu BreezeACCESS/AU-BS Official Release Version – 4.0.40 Release Date: Thu Dec 20 21:05:08 2001 Info Screens ==================== 1 – Show Unit Status 2 – Show Basic Parameters 3 – Show Advanced Parameters S – Show All Parameters >>> Figure 2-1: Info Screens Menu The Info Screens menu enables viewing of the current values of various parameter sets. The parameter sets are identical to the main parameter groups in the configuration menus.
BreezeACCESS Version 4.3 Operations and Administration 2-4 Console Speed – Displays the speed defined in the unit for the connected terminal, used for running the terminal emulation program. Number of Associations Since Last Reset – For SUs - displays the total number of associations with any AU since the last reset, including duplicate associations with the same AU.
Menus and Parameters 2-5 The following parameter appears for GPS Modules only: Unit Status – Indicates the status of the GPS antenna. Either one of the following messages may be displayed: UTC is available; date..; time..: This message indicates that the GPS antenna has synchronized with the satellite system and that the BS-GU is functioning properly. The message may include an incorrect time and date, such as a date in 1999.
BreezeACCESS Version 4.3 Operations and Administration 2-6 includes some additional useful read-only information such as the Number of Hopping Frequencies (SU and AU). Unit Control Menu The Unit Control menu includes the following options: Reset Unit – Resets the BreezeACCESS unit and applies any changes made to the system parameters. Defaults Settings – Resets the unit to a predefined set of default parameters or to save the current configuration as Operator Defaults.
Menus and Parameters 2-7 Table 2-1: Parameters not changed after Set Complete/Partial Factory Defaults Parameter Complete Partial – Admin Partial Installer Unit Control Parameters √ Passwords √ √ Event Log Policy √ Auto Configuration Option √ IP Parameters IP Address √ √ Subnet Mask √ √ Default Gateway Address √ √ DHCP Option √ √ Access to DHCP √ √ ESSID √ √ Operator ESSID Option √ √ Operator ESSID √ √ Best AU Support √ √ Preferred AU MAC Address √ √ ACSE Option
BreezeACCESS Version 4.
Menus and Parameters 2-9 Set Complete Operator Defaults – Available only with Administrator access rights. Set the unit to its’ Operator Defaults configuration. After the next reset, all parameters will revert to their Operator Defaults values, except for the parameters that are marked in the “Complete” column of Table 2-1‚ page 2- . Operator Defaults configuration can be defined by the Administrator (see Save Current Configuration As Operator Defaults below).
BreezeACCESS Version 4.3 Operations and Administration 2-10 Change Password – Changes the password(s). A user with Installer access rights can change the passwords for Read Only and Installer levels. A user with Administrator access rights can change the passwords of all levels. Valid values: A string of up to 8 printable ASCII characters. Table 1-1‚ page 1-2 lists the default passwords for each of the access levels.
Menus and Parameters 2-11 for storing it. Events are classified according to their severity level: Trace (lowest severity), Message, Warning, Error or Fatal (highest severity). The severity at which events are saved in the Event Log is configurable. Events from the configured severity and higher are saved and may be displayed upon request. Log history can be displayed up to the full number of current active events.
BreezeACCESS Version 4.3 Operations and Administration 2-12 c. The address of the TFTP server and the proper name of the configuration file must be configured in the DHCP server: The Server Address should be specified in the ‘sname’ field of the DHCP header. The code for this option is 66, and the minimum length is 1. It must include a legal IP address, with a maximum length of 64 characters (maximum length includes spaces. Extra characters will be ignored).
Menus and Parameters 2-13 Basic Configuration Menu The Basic Configuration menu includes all the parameters that are necessary for the initial installation and operation of the unit. Once the unit is properly installed and operational, other parameters can be configured either locally using the monitor program or remotely using Telnet, SNMP management or TFTP for loading to the unit a pre-prepared configuration file.
BreezeACCESS Version 4.
Menus and Parameters 2-15 Site Survey Menu The Site Survey menu provides various tests and counters for verifying the quality of the wireless link and the proper operation of the unit. These tests can be used to help determine where to position the units for optimal coverage, to align antennas and to assist in troubleshooting. Traffic Statistics (AU and SU) The traffic statistics can be used to monitor, interpret and analyze the wired and wireless links performance.
BreezeACCESS Version 4.3 Operations and Administration 2-16 Wireless Link Counters The unit transmits data frames received from the Ethernet port, as well as self-generated control and wireless management frames, to the wireless media. After transmission of a unicast frame, the unit waits for an acknowledgement (ACK) message from the receiving unit. Some control and wireless management frames as well as broadcast and multicast frames that are sent to more than one unit are not acknowledged.
Menus and Parameters 2-17 If the ACSE Option is enabled, then in addition to the total count, there are also separate counters for total number of data frames and voice (RTP) frames. The voice frames count includes fax frames. This is true also for Subscriber Units that do not support voice in cells where the ACSE Option in the AU is enabled. In this case the Voice count should be 0.
BreezeACCESS Version 4.3 Operations and Administration 2-18 Bad fragments received – Displays the number of frames received from the wireless media with errors (CRC errors). Duplicate frames discarded – Displays the number of frames discarded due to receiving multiple copies. If an acknowledge message was not received by the originating unit, the same data frame can be properly received twice (or more).
Menus and Parameters 2-19 Hopping Statistics Num The number of the information row, assigned automatically and sequentially by the program. Freq The hopping frequency, according to the hopping sequence. Rx The accumulated number of frames received at the specified frequency since last reset. Tx The accumulated number of frames transmitted successfully at the specified frequency since last reset. RTx The accumulated number of frames re-transmitted at the specified frequency since last reset.
BreezeACCESS Version 4.3 Operations and Administration 2-20 Start Sending – Starts transmission of ping frames. Stop Sending – Stops the transmission of ping frames. The test will end automatically once the number of pings that were sent has reached the value specified in the No. of Pings parameter (described above). The Stop Sending option can be used to end the test before completing the specified number of pings, or if continuous pinging was selected.
Menus and Parameters 2-21 Sp (Special): 5 Addresses that always exist: The MAC address of the AU (appears twice as it is learned from both the Ethernet and the wireless ports) Alvarion’s Multicast address (01:20:D6:00:00:01, also twice). The system handles this address as a Broadcast address.
BreezeACCESS Version 4.3 Operations and Administration 2-22 The SW version of the SU.
Menus and Parameters 2-23 Per-rate Counters (AU and SU) Resets or displays the per-rate counters. The per-rate counters display the number of frames (excluding retransmissions) transmitted since the last reset at each of the rates (1 Mbps, 2 Mbps, 3 Mbps) and the total number of frames that were retransmitted at each of the rates. In the AU the information is provided for each of the associated SUs, identified by their MAC address.
BreezeACCESS Version 4.3 Operations and Administration 2-24 AU Alarms (IF-based AU Only) The AU Alarms feature enables to identify and alert upon the detection of a potential problem in the outdoor unit of the AU, or another problem that causes significant degradation in the performance of the wireless link. When the AU Alarms Option is enabled, three types of tests are performed: Traffic Statistics tests, Power tests and Associations test.
BreezeACCESS Version 4.3 Operations and Administration 2-26 Based on the RSSI information responses from the SUs, the AU performs a calculation of the SU Rx Power Average Delta, defined as the average difference for all SUs between the last RSSI at the SU and the previous (one before last) RSSI. The average is calculated only for SUs that responded to both of the last two polling message.
Menus and Parameters 2-27 Association Tests If the AU was reset 3 times because no SU became associated with it, a No Associations critical alarm will be generated, provided that previously the AU was associated with at least Minimum Number Of SUs. An All Associations Lost major alarm is generated if no response was received by the AU to the last three polling messages, provided that prior to that, the average number of responding SUs was not lower than the Minimum Number Of SUs.
BreezeACCESS Version 4.3 Operations and Administration 2-28 All Associations Lost Alarm Severity: Major On Conditions: No response from any SU to the last 3 polling messages, and prior to that the average number of responding SUs was not lower than the Minimum Number Of SUs. Off Conditions: a. At lease one SU became associated with the AU -ORb. All alarms were cleared -ORc. AU Alarms Option was disabled Possible Problem: Unlocked synthesizer, very low Tx power or another major HW problem.
Menus and Parameters 2-29 High Retransmissions Rate Alarm Severity: Minor, Major On Conditions: Minor Severity Alarm: a. The Retransmissions Current Rate exceeds the Retransmissions Minor Alarm Threshold, and is higher than the Retransmissions Average Rate by at least Retransmissions Minor Alarm Minimum Delta, -ORb. The Retransmissions Current Rate has dropped below the Retransmissions Major Alarm Threshold but is still higher than the Retransmissions Minor Alarm Threshold.
BreezeACCESS Version 4.3 Operations and Administration 2-30 High Dropped Frames Rate Alarm Severity: Minor, Major On Conditions: Minor Severity Alarm: a. The Dropped Frames Current Rate exceeds the Dropped Frames Minor Alarm Threshold, and is higher than the Dropped Frames Average Rate by at least Dropped Frames Minor Alarm Minimum Delta, -ORb. The Dropped Frames Current Rate has dropped below the Dropped Frames Major Alarm Threshold, but is still higher than the Dropped Frames Minor Alarm Threshold.
Menus and Parameters 2-31 High CRC Error Rate Alarm Severity: Minor, Major On Conditions: Minor Severity Alarm: a. The CRC Error Current Rate exceeds the CRC Error Minor Alarm Threshold, and is higher than the CRC Error Average Rate by at least CRC Error Minor Alarm Minimum Delta, -ORb. The CRC Error Current Rate has dropped below the CRC Error Major Alarm Threshold but is still higher than the CRC Error Minor Alarm Threshold.
BreezeACCESS Version 4.3 Operations and Administration 2-32 High Duplicate Frames Rate Alarm Severity: Minor, Major On Conditions: Minor Severity Alarm: a. The Duplicate Frames Current Rate exceeds the Duplicate Frames Minor Alarm Threshold, and is higher than the Duplicate Frames Average Rate by at least Duplicate Frames Minor Alarm Minimum Delta, -ORb.
Menus and Parameters 2-33 The AU Alarms Menu The AU Alarms menu enables to configure relevant parameters and to view current statistics. The AU Alarms menu is available only with Administrator access rights, except for Show All AU Alarms Parameters and Data that is also available with Installer access rights. AU Alarms Option - Enables to enable or disable the AU Alarms feature. The default is Disable.
BreezeACCESS Version 4.
Menus and Parameters 2-35 Default value: 15 (dBm). Show AU Rx Power Test Parameters and Data - Displays the value of the AU Rx Power Decrease Threshold and the current AU Rx Power Average Delta. Responding SUs - a sub menu that includes the following options: Minimum Average Number Of SUs - Enables to define the minimum average number of SUs required for association tests.
BreezeACCESS Version 4.3 Operations and Administration 2-36 Advanced Configuration Menu The Advanced Configuration menu provides access to all the parameters, including the parameters that are available through the Basic Configuration menu.
Menus and Parameters 2-37 DHCP Client DHCP Options – Displays the current status of the DHCP (Dynamic Host Configuration Protocol) support, and allows selecting a new operation mode. The available options are: Disable – Use manual procedure for configuring the IP parameters. DHCP Only – Search for a DHCP Server and obtain the IP parameters from it (IP Address, Subnet Mask and Default Gateway Address). Automatic – Search for a DHCP Server for configuration of the IP parameters.
BreezeACCESS Version 4.3 Operations and Administration 2-38 parameter is only set in the AU. All the SUs learn it from the AU during the association process. The valid values depend on the applicable hopping standard (see Table ý3-2 on page 31). The default value is 1. Hopping Set –Displays the selected hopping set. Each hopping standard has 3 hopping sets. The Hopping Set selected in this screen determines which hopping sequences are available in the Hopping Sequence screen.
Menus and Parameters 2-39 Table 2-3: Country Standards Supported by BreezeACCESS II Country Standard Frequency Range [MHz] Number of Channels Hopping Sequences per Hopping Set Hopping Sync Support Australia 2402 to 2461 60 20 No Canada 2452 to 2481 30 10 No Europe ETSI 2402 to 2480 79 26 Yes France 2448 to 2482 35 11 Yes Israel 2421 to 2455 35 11 Yes Korea 2430 to 2452 23 4 Yes Japan 2473 to 2495 23 4 Yes Netherlands 2454 to 2468 15 5 Yes Spain 2447 to 2473
BreezeACCESS Version 4.3 Operations and Administration 2-40 NOTE: Synchronization is not allowed by the radio regulations in certain countries. In units using such standards, the Hopping Sync option is not supported. See Table 2-3‚ page 2-39 for information on synchronization support in the standards of various countries. ESSID Parameters The ESSID is a string used to identify a wireless network. It prevents the unintentional merging of two co-located wireless networks.
Menus and Parameters 2-41 Best AU Selection Parameters In BreezeACCESS systems with software version 3.0 and below an SU can associate with any AU it can communicate with, provided they both use the same ESSID. An SU that can communicate with more than one AU using the same ESSID becomes associated with the first AU it “finds”, not necessarily the best choice in terms of quality of communication or other factors such as number of SUs serviced by each AU.
BreezeACCESS Version 4.3 Operations and Administration 2-42 neighboring AUs. A higher number may result in a better decision at the cost of an increased scanning time during which the SU is not operational. Valid values: 1 - 255. Default value: 20. The scanning time can be calculated based on the following formula: Scanning Time (seconds) = N * C * 0.019 N = Number of scanning attempts C = Number of channels in the hopping sequence 0.
Menus and Parameters 2-43 page 2-48). An AU whose associations load status is full cannot be selected as the Best AU, even if its’ computed mark is the highest. ESSID – The ESSID of the AU In addition to the neighboring AU data table, the following information is displayed: Best AU Support Preferred AU MAC Address Number of Scanning Attempts Associated AU MAC Address (the MAC address of the selected AU) Run Time ESSID (the ESSID of the selected AU).
BreezeACCESS Version 4.3 Operations and Administration 2-44 received at an optimal level, or as high as possible if the optimal range cannot be reached because of specific link conditions. Each time that the SU tries to associate with the AU (following either a reset or loss of synchronization), it will initiate transmissions using the Current Transmit Power Control, which is the last value that was previously used by the ATPC mechanism.
Menus and Parameters 2-45 Table 2-4 -.
BreezeACCESS Version 4.3 Operations and Administration 2-46 Minimum RSSI Level: Enables you to define the lowest level at which you want each SU to be received at the AU (the lower limit of the optimal reception level range). Available values: -100 to 0dBm. Default value: -74 dBm Maximum RSSI Level: Enables you to define the highest level at which you want each SU to be received at the AU (the higher limit of the optimal reception level range). Available values: -100 to 0 dBm.
Menus and Parameters 2-47 ATPC Parameters in IF Based SU ATPC Option: To enable or disable the Automatic Transmit Power Control (ATPC) algorithm. The parameter takes effect immediately. However, when changed from Enable to Disable, the transmit power level shall remain at the last level determined by the ATPC algorithm before it was disabled. It will change to the value configured for the Transmit Power Control parameter only after the next reset. The default is Enable.
BreezeACCESS Version 4.3 Operations and Administration 2-48 symmetrical and that this value is a good indication to the level at which the SU is received by the AU. If the measured RSSI is less than a certain threshold, it is recommended to decrease the Maximum Data Rate of the SU in accordance with Table 2-5 (including a 3 dB safety margin).
Menus and Parameters 2-49 Default value: 512. NOTE: There is no aging time for SUs. An SU will be removed from the list of associated SUs only upon occurrence of any of the following: (1) The AU received from another AU a SNAP frame with the SU MAC address indicating that the SU has become associated with the other AU, or (2) The AU has decided that the SU aged out following its failure to acknowledge a certain number of consecutive frames transmitted to it.
BreezeACCESS Version 4.3 Operations and Administration 2-50 can be conducted by the SUs associated with this AU. If the number of active voice sessions reaches this number, any additional SU trying to initiate a voice session shall not get a dial tone. As this value increases, voice quality may deteriorate as more users share the same bandwidth for voice sessions. The selection range is from 0 to 50. The default value is 12. NOTE: A voice session is defined as a voice connection between an SU and an AU.
Menus and Parameters 2-51 sessions generated by external equipment and routed via the Ethernet port of the Subscriber Unit. ACSE Option – Applicable only for an AU that provides services to Subscriber Units with voice capabilities. To enable/disable the ACSE Voice Scheduler protocol. The AU controls the operation of all the SUs it serves according to the configured ACSE Option. The default is Disable.
BreezeACCESS Version 4.3 Operations and Administration 2-52 The default value is 30. Show ACSE Parameters – Displays the current settings of all ACSE parameters. The display in the SU includes the ACSE Option, which is only configurable in the AU. It also includes the ACSE Dwell Time, which is set to 60 milliseconds. Scanning Mode (SU only) – Defines whether to use Active or Passive scanning. In active scanning, the SU transmits a Probe Request upon power-up.
Menus and Parameters 2-53 SU-I: 60 (RSSI units) Send Roaming SNAP (SU- only, except to SU-BD and SU-BD1V) This feature is applicable only to mobile units that can roam among AUs. The feature enables fast distribution of the new location for all clients that are behind the SU. When enabled, the SU will send multicast SNAP messages via the wireless link each time it associates with an AU, except to the first association after reset.
BreezeACCESS Version 4.3 Operations and Administration 2-54 managed by stations whose IP addresses match one of the entries in the Set Network Management IP Addresses (see next parameter) that are connected to the unit via the defined port(s). Available options are: Disable – No IP address based filtering Activate Management IP Filter On Ethernet Port – Applicable only if the Access to Network Management parameter is configured to either From Ethernet Only or From Both Ethernet & Wireless Link.
Menus and Parameters 2-55 SNMP Traps – This submenu enables configuring SNMP Traps sending parameters. It includes the following options: Traps Control - Enables/disables transmission of SNMP traps; Send SNMP Traps – Enables/disables sending of SNMP traps. Available options are: Enable Traps Sending - enables sending of SNMP Traps. The Traps that will be sent can be defined by the Per Trap Control menu.
BreezeACCESS Version 4.3 Operations and Administration 2-56 Trap Unit Send AU Alarms Traps IF-based AU Default Enable Traps Sending (applicable to all AU Alarms Traps) SNMP Traps IP Destination – Displays the current values of 3 IP addresses that are defined as the trap destinations. Allows entering a new address for each of the 3 entries. The default of all three SNMP Traps IP Destinations is 0.0.0.0.
Menus and Parameters 2-57 The VLAN Support option allows viewing and setting of the following parameters: VLAN ID-Data (SU unit only) – Applicable for Access links only. Sets the VLAN ID for data frames, identifying the VLAN to which the unit belongs. Valid values: 1 to 4094. Default value: 1. Frames received from the Wireless link port: Only tagged frames with VLAN ID (VID) value equal to the VLAN ID Data defined in the unit are forwarded to the Ethernet port.
BreezeACCESS Version 4.3 Operations and Administration 2-58 • Management frames generated by the unit will not be tagged. The following table summarizes the functionality of the internal management port in accordance with the value of the VLAN ID – Management parameter. The table is valid for all link types.
Menus and Parameters 2-59 • • Management frames generated by the unit will not be tagged. If the Voice Priority Tag Option is enabled, a VLAN Priority Tag is inserted in all voice frames (RTP packets) generated by the unit before transmission to the Wireless or Ethernet port. The tag includes a VID value of zero and the VLAN Priority – Voice parameter.
BreezeACCESS Version 4.3 Operations and Administration 2-60 Action Data Port (SU) Accept from Ethernet Untagged frames Accept from Wireless Tagged frames, matching VID-D Tag Insert VID-D, PID-D (to wireless) Tag Remove Yes (to Ethernet) Legend: VID-D: VLAN ID-Data PID-D: VLAN Priority-Data Trunk Link – Transfers only tagged frames, because all devices connected to it are VLAN-aware: Only tagged data frames received on Ethernet or wireless link ports are forwarded.
Menus and Parameters 2-61 Table 2-10: VLAN Data Port Functionality Summary – Trunk Link Action Data Port (SU and AU) Accept from Ethernet Tagged frames. If Forwarding is enabled, only frames with VLAN ID values which are included in the Forwarding list are forwarded. Accept from Wireless Tagged frames. If Forwarding is enabled, only frames with VLAN ID values which are included in the Forwarding list are forwarded.
BreezeACCESS Version 4.3 Operations and Administration 2-62 VLAN Forwarding Support – Enables or disables the VLAN Forwarding feature. Available selections are Disable and Enable. The default selection is Disable. Add Forwarding VLAN ID – Adds a VLAN ID to the VLAN Forwarding List. One VLAN ID can be entered each time. The maximum number of VLAN IDs in the VLAN Forwarding List is 20. Valid values are 1 to 4094. Remove Forwarding VLAN ID – Removes a VLAN ID from the VLAN ID Forwarding List.
Menus and Parameters 2-63 Show VLAN ID Relaying List – Displays the values of the VLAN IDs that are included in the VLAN Relaying List. NOTE: If the VLAN ID Relaying List is empty and the VLAN Relaying Support is enabled, then all wireless link relayed data frames will be discarded. If the VLAN ID Relaying List and Forwarding List Support are both enabled, all the VLAN IDs configured in the Relaying List must also be configured in the Forwarding List.
BreezeACCESS Version 4.3 Operations and Administration 2-64 Valid values are 0-7. The default value is 0. NOTE: Packets Received from the Ethernet port with a ToS Precedence value higher than the ToS Precedence Threshold defined will be routed to the Mid queue. VLAN Priority – Management (AU, SU and GU)– Displays and sets the value of the VLAN Priority field for management frames in units with a VLAN ID- Management (or VLAN ID – Management & Voice) value other than 65535.
Menus and Parameters 2-65 The default value is 4. Show VLAN Parameters – Displays the current values of the VLAN Support parameters. ToS Priority Parameters (AU and SU) ToS Priority – To set voice priority parameters to support end-to-end IPv4 Type of Service (ToS) Layer 3 prioritization according to RFC 791.
BreezeACCESS Version 4.3 Operations and Administration 2-66 Filter Options – Defines the Ethernet broadcast filtering functionality of the unit.
Menus and Parameters 2-67 Disable– ARP Broadcast messages are filtered or transmitted according to the general filtering criteria set by the Filter Options parameter. Enable– ARP Broadcast messages are transmitted regardless of the selected value of the Filter Options parameter. The default selection is Enable. Other Bridging Parameters LAN to Wireless Link Bridging Mode (AU only) – Controls the flow of information from the Ethernet backbone to the wireless media.
BreezeACCESS Version 4.3 Operations and Administration 2-68 Ports Control (SU only) - To enable/disable the Ethernet and/or Voice port. The Ports Control submenu includes the following options: Ethernet Port Control - To enable/disable non-management traffic to/from the Ethernet port. All current data sessions will be terminated. The unit may still be managed via the Ethernet port even when it is disabled for data traffic. The default selection is Enable.
Menus and Parameters 2-69 Performance Parameters (AU and SU) The Performance Parameters menu includes the following parameters: RTS Threshold – Defines the minimal frame size to require RTS/CTS (Request To Send/Clear To Send) handshake. Frames with a size below the RTS Threshold value are transmitted directly to the wireless link without being preceded with RTS frames.
BreezeACCESS Version 4.3 Operations and Administration 2-70 Minimum Contention Window – The BreezeACCESS system uses a special mechanism based on detecting the presence of a carrier signal (Carrier Sense Multiple Access-CSMA) and analyzing the information contained in the transmissions of the AU to estimate the activity of other SUs served by the same AU. The target is to minimize collisions in the wireless media resulting from trials of more than one unit to transmit at the same time.
Menus and Parameters 2-71 attempt) is based on counting transmissions, retransmissions and successful windows . A window is defined as N consecutive transmission or retransmission attempts, defined by the Multi-Rate Decision Window Size parameter. A successful window is a window in which the number of failed transmissions is not higher than a defined threshold. A transmission is defined as failed if an ACK was not received after the first transmission of a frame.
BreezeACCESS Version 4.3 Operations and Administration 2-72 Dwell Time (AU only) – The time spent on a radio channel before hopping to the next channel according to the operational hopping sequence. The allowed selections are 32, 64 and 128 Kilo-microseconds. The default value is 128 Kilo-microseconds. When the ACSE Option is enabled this parameter is not applicable and the dwell time is the ACSE Dwell Time, set to a fixed value of 60 milliseconds.
Menus and Parameters 2-73 Level, it shall be considered as interference and it becomes the updated Current Noise Floor. Carrier to Interference Difference Level is the minimal difference between the Current Noise Floor and the level of a signal that will be defined as a “good” one. This algorithm allows the unit to identify and track temporary high level interference and to adjust the decision threshold accordingly.
BreezeACCESS Version 4.3 Operations and Administration 2-74 User Defined Addresses Only (only IP messages from/to IP addresses included in the User Filter Addresses list pass). PPPoE Protocol Only (only PPPoE frames pass - Ethernet type 0x8863 and 0x8864). The default selection is Disable. Set User Filter Address – Displays the current User Filter IP addresses. Allows you to enter up to 8 IP addresses to be used if the User Defined Addresses Only option was selected in the User Filtering Option above.
Menus and Parameters 2-75 that may influence the performance of the wireless link. In some situations the minimum rate (CIR) cannot be provided. This may occur as a result of high demand and poor wireless link conditions and/or high demand in cells with over subscription (total CIR higher than 1600Kbps). When this happens, actual information rate will be lower than CIR.
BreezeACCESS Version 4.3 Operations and Administration 2-76 CIR: AU to SU (SU only) – Sets the Committed Information Rate of the down-link from the AU to the SU. The CIR value cannot be higher than the corresponding MIR value. Valid values are from 0 to 2200Kbps. The default value is 64Kbps. CIR: SU to AU (SU only) – Sets the Committed Information Rate of the up-link from the SU to the AU. The CIR value cannot be higher than the corresponding MIR value. Valid values are from 0 to 2200Kbps.
Menus and Parameters 2-77 high number of subscribers are in locations that do not enable proper communication with the AU at the highest data rate. Valid values: 0 – 70 (%). Default value: 70 (%). Mir Only option (AU only) – Enables or disables the option of forcing the MIR/CIR algorithm to use MIR values only. The MIR/CIR algorithm determines the actual information rate for each of the supported SUs under changing demand conditions, based on the configured CIR and MIR values.
BreezeACCESS Version 4.3 Operations and Administration 2-78 the client and RADIUS server, using a method based on the RSA Message Digest Algorithm MD5. The Access-Request is submitted to the RADIUS server via the network. If no response is returned within a length of time, the request is re-sent a number of times. Once the RADIUS server receives the request, it validates the sending client. A request from a client for which the RADIUS server does not have a shared secret must be silently discarded.
Menus and Parameters 2-79 Valid values: A string of up to 20 printable ASCII characters, case sensitive. Default value: RadiusSecret1234. Authentication Parameters Menu The implementation is based on RFC 2865. The mechanism allows an SU to synchronize and associate to its AU, then request authentication from the RADIUS server. Only if the authentication is successful the user will receive services (data and voice).
BreezeACCESS Version 4.3 Operations and Administration 2-80 Server Accounting IP Address is configured to an address other than 0.0.0.0., the SU enables the RADIUS accounting client. The default is Disable. RADIUS Server Accounting IP Address –To define the IP address of the RADIUS server to be used for accounting. The default address is 0.0.0.0 (none). RADIUS Server Accounting Port – Specifies the UDP port number used by the Radius server for accounting. Valid values are 1000 to 65535.
Menus and Parameters 2-81 Table 2-13: Ethernet Vendor Specific Record Structure (Vendor Specific ID is 710) Field Format Description Traffic Type 1 hexadecimal digit Data (0)/Management (1)/Voice (2). VLAN ID 3 hexadecimal digits VLAN ID. Layer 3 Protocol 4 hexadecimal digits Third layer protocol type (IP, ARP). Remote IP Address xxx.xxx.xxx.xxx (decimal format) The remote IP Address. IP Type Of Service 2 hexadecimal digits Precedence/ Delay/ Throughput/ Reliability.
BreezeACCESS Version 4.3 Operations and Administration 2-82 Shared Key: Authentication enabled. The authentication messages are encrypted. An SU configured to use Shared Key can be authenticated only by an AU configured to use Shared Key, provided they both use the same WEP Key. Both the WEP Key number and the WEP Key should be identical at both sides of the link. Support All (AU only): The AU authenticates all SUs, regardless of the Authentication Algorithm and WEP Key configured in the SU.
Menus and Parameters 2-83 NOTE: It is recommended to change the WEP Keys periodically, to enhance system security. Voice Parameters (Subscriber Units with Voice Support Only) The parameters in the Voice Parameters menu include the following options: Volume – Sets the gain of the voice signal to the earphone. Available range is 0 dB to -20 dB in 1 dB steps. The default value is -3 dB. Echo Cancellation – Enables or disables the built-in echo cancellation feature. The default value is Enable.
BreezeACCESS Version 4.3 Operations and Administration 2-84 The allowed range differs among codecs, in accordance with the different packet sizes (30 ms for G723.1, 10 ms for G729 and 5 ms for G711). The valid values and default values are: G723 Frames Per Packet – Valid range 1-8, Default value is 2 G729 Frames Per Packet – Valid range is 1-12, Default value is 6. If upgrading from a previous version, this value must be set to 6 if ACSE Option is enabled.
Menus and Parameters 2-85 into the IP address and to register its own phone number and IP address with the Gatekeeper. The default selection is Disable. GateKeeper/GateWay IP Address – Specifies the IP address of the Gateway/Gatekeeper. If the Gatekeeper Option parameter (see above) is set to Enable, an IP address must be specified. The default value is 0.0.0.0. Alternate Gatekeeper Option - Enables or disables the Alternate Gatekeeper feature.
BreezeACCESS Version 4.3 Operations and Administration 2-86 assumed to be the destination IP address. 12- and 3-digit numbers are allowed. 3- digit numbers are used to dial to stations in the same subnet, and 12- digit number are used to dial to any IP address. If a 3-digit number is dialed the Setup message is sent to the corresponding IP address in the local subnet. When dialing a 12-digit number (e.g. abcdefghijkl), the Setup message is sent directly to the IP address abc.def.ghi.jkl.
Menus and Parameters 2-87 NOTE: This information element is encoded according to Figure 4-11/Q.931 and Table 4-6/Q.931. The SU support only H323 Speech traffic and a change of the default value is not recommended. A change will be needed only as result of special PSTN switch requirements. Dialing Prefix Parameters – Supports definition of prefix strings indicating an inter-regional or international call.
BreezeACCESS Version 4.3 Operations and Administration 2-88 Default value: 0. Registration TTL – Defines the registration Time To Live. Registration is the process by which an endpoint informs the Gatekeeper of its Transport Addresses and alias addresses. Registration must occur before any calls are attempted and may occur periodically as necessary (for example, at endpoint power-up). After Registration process has finished an endpoint will no longer send Registration Request (RRQ) messages.
Menus and Parameters 2-89 Fax Relay – Defines the use of T.38 protocol for relaying fax messages. T.38 is a protocol dedicated to fax. When the Fax Relay Option is enabled, fax signals are demodulated at the voice/fax gateway and sent over the IP network as IP fax packets (IFP) using UDP. A redundancy mechanism can be employed to restore IFP fax data packets. At the other end of the IP network, the remote gateway decodes IP fax packets and regenerates fax signals.
BreezeACCESS Version 4.3 Operations and Administration 2-90 1200-baud tone modulation in accordance with Bellcore 202 standard. The Caller ID parameter is supported only by units using a Voice card HW revision D and higher. The following options are available: Disable ETSI DT-AS: CID signaling in accordance with ETSI ETS 300 659 -1, using Dual Tone Alerting Signal to indicated to the called terminal that CID data transmission is to be expected.
Menus and Parameters 2-91 Upon enabling overlap sending, the settings of other dialing parameters are overridden as follows: a. IP Dialing Option, Dialing Prefix Option and Stop Dialing Indicator are disabled even if the applicable parameter is set to Enable. b. Automatic Prefix is not used and Stop Dialing Timeout has no effect. The default selection is Disable.
BreezeACCESS Version 4.3 Operations and Administration 2-92 Error Tone – Defines the tone transmitted to the earphone to indicate that the system cannot currently support the call (e.g. if for any reason the call was disconnected because of a problem in the wireless link or incompatible capabilities) or if the user did not hang up after exceeding the specified duration of the Dial, Ring Back, Busy or Congestion Tones.
Menus and Parameters 2-93 Cadence Off – The silence time (on) in the ringing-silence sequence of the Ringer. Valid values are 100 – 10,000 milliseconds. Duration - The maximum duration of activating the ringer. Ringing will cease upon detecting off-hook condition. Valid values are 0 – 10,000 seconds. Timeouts – Defines the following timeouts: Min. Flash Detect Timeout and Max. Flash Detect Timeout – A short on-hook time that is between the values of these two parameters will be considered as Hook Flash.
BreezeACCESS Version 4.
Menus and Parameters 2-95 Table 2-18: Parameters of Call Progress Tones and Ringer – United Kingdom Frequency 1 Frequency 2 Cadence On (ms) Duration (s) Tone Freq (Hz) Level (dB) Freq (Hz) Level (dB) Off (ms) Dial Tone 350 -18 440 -18 Ring Back 400 -18 450 -18 400 200 60 Busy 400 -18 0 0 375 375 15 Congestion 400 -18 0 0 400 350 0 Error 400 -18 0 0 200 200 0 High Level Error 0 0 0 0 0 0 0 Ring Frequency 25 400 200 60 15 Table 2-19: Parameters of
BreezeACCESS Version 4.3 Operations and Administration 2-96 Table 2-21: Timeouts Min. Flash Detect (ms) Max Flash Detect (ms) Disconnect (ms) Inter-digit (ms) Called Party Release (s) Germany 120 1000 1000 100 0 USA 120 1000 1000 100 0 Sweden 120 1000 1000 100 0 France 120 1000 1000 100 0 United Kingdom 120 1000 1000 100 0 Belgium 120 1000 1000 100 0 Chile 220 320 320 500 60 Country Manual Revision: 3.
Menus and Parameters 2-97 Hopping Parameters (GU) The Hopping Parameters Menu allows configuration of the hopping mechanism. The GPS modules deliver signals to the Access Units that insure that their hopping patterns are fully synchronized. This includes synchronizing the time each unit starts a new hop and ensuring that units start the hopping sequence simultaneously.
BreezeACCESS Version 4.3 Operations and Administration 2-98 antenna to generate the synchronization signals for the AUs. When two or more BS-GU modules are daisy-chained, the signals from the GPS antenna are transferred to all "slave" BS-GU modules via the SYNC OUT - SYNC IN cable, and all BS-GUs use these signals to generate synchronization signals for their AUs.
Menus and Parameters 2-99 Automatic Recovery Mode - Enables to control an automatic recovery process: Automatic Recovery Option - To enable or disable automatic initiation of antenna recovery process. If a GPS antenna is not used, the Automatic Recovery Option should be disabled. The default selection is Enable. Automatic Recovery Interval - To define the time interval between two consecutive initiations of automatic antenna recovery processes.
BreezeACCESS Version 4.3 Operations and Administration 2-100 Show Alarm Parameters. Alarms In Names The Alarms In Names menu allows names for each of the four external alarm indications that can be connected to the AL IN connector to be defined. These names can reflect the specific environment in which the module is being used (e.g. “Smoke Detector 1” or “Main Door”). Each Alarms In Name can contain up to 31 printable ASCII characters (case sensitive). The default names are Alarm In 1 through Alarm In 4.
Menus and Parameters 2-101 Alarms Out Control The Alarms Out Control menu allows the functionality of the Alarms Out control mechanism to be defined. Its main purpose is to support “manual” activation/deactivation of each of the Alarms Out either locally or remotely using Telnet or SNMP. For each of the three Alarms Out, the following control options are available: 0 – Turn Alarm OFF (even if it should be ON according to the definition in the Automatic Alarms Out Definition Menu).
BreezeACCESS Version 4.3 Operations and Administration 2-102 Name: Name according to the name defined in the Alarms In Names Menu. Definition: NONE, Alarm In # or ANY, according to the configuration in the Automatic Alarms Out Definition Menu. Control: OFF, ON or AUTO, according to the configuration in the Alarms Out Control Menu. Status: ON or OFF. Manual Revision: 3.
BreezeACCESS II Version 4.3 Revision 3.
Appendix A: Configuration Download/Upload This appendix describes the method of configuring a large number of BreezeACCESS units at once.
BreezeACCESS Version 4.3 System Manual A-2 The Configuration Download/Upload feature in BreezeACCESS units simplifies the task of remotely configuring a large number of units using TFTP protocol. By downloading the configuration file to a PC it is possible to view all the parameters configured at the unit, as it is a plain text ASCII file. It is necessary to edit the file by a using simple editor and to remove certain parameters or change their values prior to uploading the configuration to another unit.
Appendix B: Software Version Loading Procedure General Firmware upgrades to the unit's FLASH memory are performed by a simple loading procedure using a TFTP application. Before performing an upgrade procedure, be sure you have the correct files and latest instructions. NOTE: Shutting down power to the unit before completion of the loading procedure may cause the unit to be inoperable. Verify that you have IP connectivity to the unit to be loaded with a new version.
BreezeACCESS Version 4.3 System Manual B-2 6. To verify the connection, ping the unit’s IP address. Verify that ping replies are being received. The procedure to be used depends on the unit’s FLASH memory type. Identify the FLASH memory type by using the monitor program, connecting the PC to the unit either directly or via Telnet. From the Main Menu, select 1 – Info Screens. From the Info Screen menu select 1 – Show Unit Status.
Appendix B B-3 NOTE: If you are upgrading a Subscriber Unit which is not associated with an AU, the unit will reset every five minutes (approximately) and the following message will be displayed: FTL: file src\wpscan.c line 262 Too large number of scanning attempts The unit will reset and it will take more than a minute before you can re-establish the connection to it.
BreezeACCESS Version 4.3 System Manual B-4 1. From the Flash Memory Control menu select 2 - Use Current Version After Reset. The Use Current Version After Reset menu opens. 2. Select 1 – Set As Default Now and press ENTER. This will actually cause the names of the two versions to switch. The previous Shadow version will now be called Current and vise versa. The following message will be displayed: UP (DOWN) Image FLASH will be operational (UP or DOWN refers to the location in the flash memory).
Appendix B B-5 NOTE: If you are upgrading a Subscriber Unit which is not associated with an AU, the unit will reset every five minute (approximately) and the following message will be displayed: FTL: file src\wpscan.c line 262 Too large number of scanning attempts The unit will reset and it will take more than a minute before you can re-establish the connection to it.
BreezeACCESS Version 4.3 System Manual B-6 1. From the Flash Memory Control menu select 2 - Use Current Version After Reset. The Use Current Version After Reset menu opens. 2. Select 1 – Set As Default Now and press ENTER. This will actually cause the names of the two versions to switch. The previous Shadow version will now be called Current and vise versa. The following message will be displayed: UP (DOWN) Image FLASH will be operational (UP or DOWN refers to the location in the flash memory).
Appendix C: Supported MIBs and Traps BreezeACCESS agents support the following MIBs: MIB-II (RFC1213) BRIDGE-MIB (RFC1286) BreezeCOM brzAccessMib BreezeCOM brzPhoneMib BreezeCOM brznetmib
Appendix C C-3 Object OID (Location in parenthesis) Description breezecomAU_I breezecomBreezeACCESS_ACCESS 21 (710.10.2.1.21) AU-I breezecomSU_BS breezecomBreezeACCESS_ACCESS 22 (710.10.2.1.22) SU-BS breezecomAU_BS_WA breezecomBreezeACCESS_ACCESS 23 (710.10.2.1.23) AU-BS-WA breezecomGU_BS breezecomBreezeACCESS_GENERAL 1 (710.10.2.2.1) GU-BS brzAccessMIB Path: breezecom OBJECT IDENTIFIER =1.3.6.1.4.1.
BreezeACCESS Version 4.3 System Manual C-4 MIB Parameter (Location in Parenthesis) Description Values/Range *RunTimeMirCirOption 710.3.3.1.9 (*ServiceParameters 9) Applicable to SU only. Indicates the actual status of the MIR/CIR option, which may be different from the setting of this parameter in the SU since it is controlled by the AU. Integer disable (0) enable (1) na (255) *MirOnlyOption 710.3.3.1.10 (*ServiceParameters 10) Applicable only to AU when CIR/MIR option is enabled.
Appendix C C-5 RADIUS Authentication Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *RadiusAuthParameters 710.3.3. 21 (brzAccessMib 21) Applicable to SU only. RADIUS Authentication parameters. *RadiusAuthOption 710.3.3. 21.1 (*RadiusAuthParameters 1) Applicable to SU only. Enables or disables the RADIUS Authentication support feature. Integer disable (0) enable (1) na (255) * RadiusServerAuthIpAddress 710.3.3. 21.2 (*RadiusAuthParameters 2) Applicable to SU only.
BreezeACCESS Version 4.3 System Manual C-6 MIB Parameter (Location in Parenthesis) Description Values/Range *DeleteOneUserFilter 710.3.3.2.3 (*UserFilterParams 3) Applicable to SU only. Deletes a single selected entry from the IP Filter Table. Integer off (0) firstEntry (1) secondEntry (2) thirdEntry (3) fourthEntry (4) fifthEntry (5) sixthEntry (6) seventhEntry (7) eighthEntry (8) na (255) *DeleteAllUserFilters 710.3.3.2.4 (*UserFilterParams 4) Applicable to SU only.
Appendix C C-7 Network Management Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *NwMngParameters 710.3.3. 4 (brzAccessMib 4) Network Management parameters. *AccessToNwMng 710.3.3. 4.1 (*NwMngParameters 1) Applicable to AU and SU. The port to be used for remote management. wlanOnly: Management E from Wireless port only. ethOnly: Management enabled from Ethernet port only. bothWlanEth: Management enabled from both Wireless and Ethernet ports.
BreezeACCESS Version 4.3 System Manual C-8 MIB Parameter (Location in Parenthesis) Description Values/Range *DeleteAllTrapAddrs 710.3.3.4.9 (*NwMngParameters 9) Applicable to AU, SU and GU. Deletes all entries from the Management Trap Table. *PerTrapControl 710.3.3.4.10 (*NwMngParameters 10) Applicable to AU, SU and GU. Per Trap Control parameters. *SendSUAssociatedAUTrap 710.3.3.4.10.1 (*PerTrapControl 1) Applicable to AU only. Enables\Disables the sending of brzaccSUassociatedAUTRAP.
Appendix C C-9 Bridge Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *BridgeParameters 710.3.3. 5 (brzAccessMib.5) Bridge parameters. *EthBroadcastFiltering 710.3.3. 5.1 (*BridgeParameters 1) Applicable to SU only. Enables/disables the filtering of Ethernet (layer2) broadcasts. disable: No filtering. ethOnly: Filter broadcasts received on the Ethernet port only. wlanOnly: Filter broadcasts received on the Wlan port only.
BreezeACCESS Version 4.3 System Manual C-10 MIB Parameter (Location in Parenthesis) Description Values/Range *VlanRelayingEntry 710.3.3. 5.2.8.2.1 (*VlanRelayingTable 1) Applicable to AU only. A VLAN Relaying Table entry. (applicable in Trunk links only). Not accessible. *VlanRelayingIdx 710.3.3. 5.2.8.2.1.1 (*VlanRelayingEntry) 1 Applicable to AU only. A read only table index for a VLAN entry in the VLAN Relaying Table. Integer 1 - 20 *VlanIdRelaying 710.3.3. 5.2.8.2.1.
Appendix C C-11 MIB Parameter (Location in Parenthesis) Description Values/Range *PortsControl 710.3.3. 5.9 (*BridgeParameters 9) Applicable to SU only. Port Control parameters *EthernetPortControl 710.3.3. 5.9.1 (*PortsControl 1) Applicable to SU only. Enable/disable the Ethernet port. When disabled, only data frames are blocked. Management frames are accepted. Integer disable (0) *VoicePortControl Applicable to SU with voice only. Enable/ Integer 710.3.3. 5.9.
BreezeACCESS Version 4.3 System Manual C-12 MIB Parameter (Location in Parenthesis) Description Values/Range *TransmitDiversity 710.3.3. 6.4 (*AirInterface 4) Applicable to SU-R, SU-I and AU-I units only. Enables the selection of the antenna(s) to be used for transmission. Integer use2Antennasn (0) antenna1 (1) antenna2 (2) na (255) *HoppingSequence 710.3.3. 6.5 (*AirInterface 5) Applicable to AU in BreezeACCESS II family only. Determines the hopping sequence to be used.
Appendix C MIB Parameter (Location in Parenthesis) *HoppingBands 710.3.3. 6.9 (*AirInterface 9) C-13 Description Values/Range Applicable to SU and AU only. In BreezeACCESS II units set in the factory to “Country Standard Protected” this is read-only, showing the Country Standard set in the factory. Integer na (255) The available values represent settings that are dependent on the specific radio band.
BreezeACCESS Version 4.3 System Manual C-14 MIB Parameter (Location in Parenthesis) Description *HoppingBands (continued) Values/Range BreezeACCESS 3.5b, 3.
Appendix C MIB Parameter (Location in Parenthesis) C-15 Description Values/Range *AddSubBand 710.3.3. 6.15.1 (*FlexSubBandDef 1) Applicable to SU and AU only. In BreezeACCESS II, V and MMDS families it adds sub-bands (f1-f2) or discrete frequencies to the list of sub-bands/frequencies to be used for generating the basic Hopping Sequence after the next reset. In BreezeACCESS XL it defines a new set of sub-bands/frequencies to be used for generating the basic Hopping Sequence after the next reset.
BreezeACCESS Version 4.3 System Manual C-16 MIB Parameter (Location in Parenthesis) Description Values/Range *ChannelSpacing 710.3.3. 6.15.5 (*FlexSubBandDef 5) Applicable to SU and AU in BreezeACCESS XL family only. Applicable only in Flexible Hopping Definition mode. Defines the minimum distances between two frequencies. (Not available in some products that only support a 2MHz Channel Spacing) Integer space1_75MHz (0) space1MHz (1) space2MHz (2) na (255) *AddFlexHopChannels 710.3.3. 6.15.
Appendix C MIB Parameter (Location in Parenthesis) C-17 Description Values/Range *ScrambledSeqTableIdx 710.3.3. 6.15. 9.5.1.1 (**ScrambledSeqEntry 1) Applicable to SU and AU only. Readonly. A Scrambled Sequence Table entry index. Integer *ScrambledSeqFreqIdx 710.3.3. 6.15. 9.5.1.2 (**ScrambledSeqEntry 2) Applicable to SU and AU only. Readonly. A Frequency Index in the Scrambled Sequence Table. DisplayString (SIZE(10)) *CallAgingTime 710.3.3. 6.16 (*AirInterface 16) Applicable to AU only.
BreezeACCESS Version 4.3 System Manual C-18 MIB Parameter (Location in Parenthesis) Description Values/Range *OperatorESSID 710.3.3. 6.21 (*AirInterface 21) Applicable to AU only. A secondary ESSID to support upgrade of existing installations. All AUs in the region should be configured to the same Operator ESSID to allow a new SU to associate with any AU. Accessible only with SNMP Write Community DisplayString (SIZE(31)) Up to 31 printable ASCII characters, case sensitive. *RunTimeESSID 710.3.3. 6.
Appendix C MIB Parameter (Location in Parenthesis) C-19 Description Values/Range *TransmitLevel 710.3.3. 6.24 (*AirInterface 24) Applicable only to SU-I and AU-I units with HW version D and higher. Sets the level in dBm of the transmitted power at the antenna port. * brzaccAtpc 710.3.3. 6.25 (*AirInterface 25) ATPC Parameters *AtpcOption 710.3.3. 6.25.1 (*Atpc 1) Applicable to IF based units and SUR-3.5ab units only. Enabling/ disabling the ATPC Algorithm.
BreezeACCESS Version 4.3 System Manual C-20 MIB Parameter (Location in Parenthesis) Description Values/Range *ACSEOption 710.3.3. 6.27.1 (*ACSEParameters 1) Applicable for AU, SU and GU. Read-only in the SU. Disable/enable the ACSE Voice Scheduler mechanism. Integer disable (0) enable (1) *ACSEDwellTime 710.3.3. 6.27.2 (*ACSEParameters 2) Applicable for AU, SU and GU. Read-only. The dwell time when the *ACSEOption is enabled. Currently set to 60 milliseconds.
Appendix C C-21 BreezeACCESS Version 4.
BreezeACCESS Version 4.3 System Manual C-22 MIB Parameter (Location in Parenthesis) Description Values/Range *ScanningMode 710.3.3.6.35 (*AirInterface 35) Applicable to SU only. Not applicable if *ACSEOption is enabled. Sets the scanning mode. passive (1) active (2) na (255) *SendRoamingSNAP 710.3.3.6.37 (*AirInterface 37) Applicable to all SUs, except to SUBD and SU-BD1V. Disables/enables the Send Roaming SNAP feature. Integer disable (0) enable (1) na (255) *AUTransmissionRateContro l710.3.3.6.
Appendix C MIB Parameter (Location in Parenthesis) C-23 Description Values/Range *CarrierSenseLevel 710.3.3. 7.7 (*PerformanceParams 7) Applicable to SU and AU. Threshold level for decision on existence of a carrier signal, indicating a transmission from another unit. DisplayString -100 to -40 (dB) *DwellTime 710.3.3. 7.9 (*PerformanceParams 9) Applicable to AU and GU. The time spent on each radio channel (hop). Applicable only when the *ACSEOption is disabled.
BreezeACCESS Version 4.3 System Manual C-24 Site Survey Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *SiteSurvey 710.3.3. 8 (brzAccessMib 8) PerHopStatisticsTable 710.3.3. 8.1 (*SiteSurvey 1) Applicable to SU and AU. Statistics accumulated since last reset and average RSSI per frequency for all hopping frequencies in the (sequence). Not Accessible. hopSeqEntry 710.3.3. 8.1.1 (perHopStatisticsTable 1) Applicable to SU and AU. A Per Hop Statistics Table entry.
Appendix C MIB Parameter (Location in Parenthesis) C-25 Description Values/Range *TotalRxFramesFromWireless 710.3.3. 8.2.3.2 (*WlanCounters 2) Applicable to SU and AU. Read-only. The total number of frames that were received from the wireless media. The count includes data and control and management frames, including beacons received from the AU. The count does not include frames that were discarded internally, bad frames and duplicate frames. Counter *TotalRetransmittedFragments 710.3.3. 8.2.3.
BreezeACCESS Version 4.3 System Manual C-26 MIB Parameter (Location in Parenthesis) Description Values/Range *SubmittedFramesLow 710.3.3. 8.2.3.11 (*WlanCounters 11) Applicable to SU and AU. Read-only. Counts the number of frames submitted to the bridge via the Low queue for transmission to the wireless media. When the ACSE Option is enabled, it counts data and RTP frames. When the ACSE Option is disabled, it counts only data frames. Counter *SubmittedFramesVoice 710.3.3. 8.2.3.
Appendix C MIB Parameter (Location in Parenthesis) C-27 Description Values/Range *TotalTxErrorsAckTOut 710.3.3. 8.2.3.23 (*WlanCounters 23) Applicable to SU and AU. Read-only. The number of transmit errors that have occurred because of an Acknowledge Timeout–a frame that was not acknowledged within the time defined by the Acknowledge Delay Limit parameter. Counter *TotalTxErrorsFail 710.3.3. 8.2.3.24 (*WlanCounters 24) Applicable to SU and AU. Read-only.
BreezeACCESS Version 4.3 System Manual C-28 MIB Parameter (Location in Parenthesis) Description Values/Range *VoiceTrafficTxFrames 710.3.3. 8.2.4.1 (*VoiceCounters 1) Applicable to SU with voice support only. Read-only. Counts the number of voice frames, including fax and T.38 redundant frames, that were transmitted to the wireless link. Counter *VoiceTrafficRxFrames 710.3.3. 8.2.4.2 (*VoiceCounters 2) Applicable to SU with voice support only. Read-only.
Appendix C MIB Parameter (Location in Parenthesis) C-29 Description Values/Range *PerHopStatistics 710.3.3. 8.4 (*SiteSurvey 4) Applicable to SU and AU. *ResetPerHopStatistics 710.3.3. 8.4.1 (*PerHopStatistics 1) Applicable to SU and AU. Reset the Per Hop Statistics counters. *MacAddressDatabase 710.3.3. 8.5 (*SiteSurvey 5) Applicable to AU only. Database by MAC Addresses for all SUs associated with the AU.
BreezeACCESS Version 4.3 System Manual C-30 MIB Parameter (Location in Parenthesis) Description Values/Range *AdbRTx1M 710.3.3. 8.5.2.1.10 (*AdbEntry 10) Applicable to AU Only. Read-only. Counts the total number of frames that were retransmitted to the SU over the wireless link at 1Mbps. Counter *AdbRTx2M 710.3.3. 8.5.2.1.11 (*AdbEntry 11) Applicable to AU Only. Read-only. Counts the total number of frames that were retransmitted to the SU over the wireless link at 2Mbps. Counter *AdbRTx3M 710.3.
Appendix C MIB Parameter (Location in Parenthesis) C-31 Description Values/Range AtpcTransmittedMessages 710.3.3. 8.6.2 (*AtpcCounters 2) Applicable to IF based AU. The total number of ATPC messages transmitted by the unit since last reset. Integer AtpcReceivedMessages 710.3.3. 8.6.3 (*AtpcCounters 3) Applicable to SU units only. The number of ATPC messages received by the unit since last reset regardless of whether the unit supports ATPC. Integer *AUAlarms 710.3.3. 8.
BreezeACCESS Version 4.3 System Manual C-32 MIB Parameter (Location in Parenthesis) Description Values/Range *MinorAlarmThreshold 710.3.3. 8.7.4.1.1.5 (*TrafficStatisticsEntry 5) Applicable to IF-based AU only. Read-write. The threshold for activating a minor severity alarm for the relevant statistics type.
Appendix C C-33 Integer 1 – 254 (SUs) *MinimumAverageNumberOfSUs 710.3.3. 8.7.7.3 (*RespondingSUs 3) Applicable to IF-based AU only. The minimum average number of SUs required for association tests *AUAlarmsStatus 710.3.3. 8.7.8 (*AUAlarms 8) Applicable to IF-based AU only. Alarms Status parameters. *AlarmsStatusTable 710.3.3. 8.7.8.1 (*AUAlarmsStatus 1) Applicable to IF-based AU only. Not accessible. AU Alarms Status Table containing the current status of each of the alarms.
BreezeACCESS Version 4.3 System Manual C-34 Unit Control Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *UnitControl 710.3.3. 10 (brzAccessMib 10) *ResetUnit 710.3.3. 10.1 (*UnitControl 1) Applicable to all products. Resets the unit and applies new parameter values. Integer cancel (0) resetSystemNow (1) *SetDefaults 710.3.3. 10.2 (*UnitControl 2) Applicable to all products. Sets unit configuration to Defaults values after the next reset.
Appendix C MIB Parameter (Location in Parenthesis) C-35 Description Values/Range *EraseEventLog 710.3.3. 10.10.3 (*EventLog 3) Applicable to all products. Deletes all entries from the Event Log file. Integer cancel (0) erase (1) *SaveCurrentConfigurationAs OperatorDefaults 710.3.3. 10.12 (*UnitControl 12) Applicable to all products. Saves the current configuration as Operator Defaults. Integer cancel (0) saveAsDefaults (1) *ExitMonitorOrTelnet 710.3.3. 10.
BreezeACCESS Version 4.3 System Manual C-36 IP Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *IpParams 710.3.3. 11 (brzAccessMib 11) *UnitIpAddress 710.3.3. 11.1 (*IpParams 1) Applicable to all products. IP address of the unit. IP address *SubNetMask 710.3.3. 11.2 (*IpParams 2) Applicable to all products. Subnet mask of the unit. IP address *DefaultGWAddress 710.3.3. 11.3 (*IpParams 3) Applicable to all products. Default gateway IP address of the unit.
Appendix C MIB Parameter (Location in Parenthesis) C-37 Description Values/Range *UnitType 710.3.3. 13.7 (*SysInfo 7) Applicable to all products. Read-only: Unit type. DisplayString (SIZE(0..32)) *AssociatedAU 710.3.3. 13.8 (*SysInfo 8) Applicable to SU only. Read-only: Associated AU MAC address. MAC address *NumOfAssociationsSinceLastReset 710.3.3. 13.9 (*SysInfo 9) Applicable to AU and SU. Read-only: The number of associations since last reset, including duplicate associations (reassociations).
BreezeACCESS Version 4.3 System Manual C-38 Alarms Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *Alarms 710.3.3. 20 (brzAccessMib 20) Alarms parameters *GpsAlarms 710.3.3. 20.1 (*Alarms 1) Applicable to GU only. GPS Alarms parameters. *AlarmInTable 710.3.3. 20.1.1 (*GpsAlarms 1) Applicable to GU only. Names and status of Alarms-In. Not accessible. *AlarmInTableEntry 710.3.3. 20.1.1.1 (*AlarmInTable 1) Applicable to GU only. An Alarms In table entry. Not accessible.
Appendix C C-39 brzPhoneMIB (applicable to SU with voice only) breezecom OBJECT IDENTIFIER =1.3.6.1.4.1.710 {(iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) breezecom(710)} breezecomPrvRev {breezecom 3} OBJECT IDENTIFIER = 1.3.6.1.4.1.710.3 brzPhoneMib {breezecomPrvRev 4 } OBJECT IDENTIFIER = 1.3.6.1.4.1.710.3.4 Note: * is used instead of the phon prefix Dialing Parameters MIB Parameter (Location in Parenthesis) Description Values *DialingParams 710.3.4.
BreezeACCESS Version 4.3 System Manual C-40 MIB Parameter (Location in Parenthesis) Description Values *InformTransferCap 710.3.4.1.14 (*DialingParams 14) Defines the value of the information transfer capability in the SETUP message. Integer speech (0) unrestricted (1) restricted (2) audio (3) unrestrictedTones (4) video (5) na (255) *DTMFRelay 710.3.4.1.15 (*DialingParams 15) Disable/enable DTMF Relay. 0 ñ Disable. DTMF is transferred inband. 1 ñ Enable. In-band DTMF is filtered.
Appendix C MIB Parameter (Location in Parenthesis) C-41 Description Values *AlternateGkOption 710.3.4.1.24 (*DialingParams 24) Setting the Alternate Gatekeeper feature. EnableManualDiscovery: the Alternate Gatekeeper IP address is specified by the Alternate Gatekeeper IP Address parameter. EnableAutomaticDiscovery: the Alternate Gatekeeper IP address is received from the Primary GK. Integer disable (0) enableManualDiscovery (1) enableAutomaticDiscovery (2) na (255) *AlternateGkIPAddress 710.3.4.1.
BreezeACCESS Version 4.3 System Manual C-42 Voice Parameters MIB Parameter (Location in Parenthesis) Description Values *VoiceParams 710.3.4.2 (brzPhonMib 2) *VoiceVolume 710.3.4.2.1 (*VoiceParams 1) Gain of signal to earphone. Integer 0-20 (-dB) na (255) *EchoCancellation 710.3.4.2.3 (*VoiceParams 3) Enables or disables the echo cancellation feature. Integer disable (0) enable (1) na (255) *VoiceCodec 710.3.4.2.4 (*VoiceParams 4) The relative priority of voice codecs. DisplayString (SIZE (0..
Appendix C C-43
BreezeACCESS Version 4.3 System Manual C-44 MIB Parameter (Location in Parenthesis) Description Values *MinimumFlashDetectTimeOut 710.3.4.3.3.1 (*TimeOuts 1) The minimum on-hook time for identifying it as a Hook Flash. Integer 0-2,000 (milliseconds) *MaximumFlashDetectTimeOut 710.3.4.3.3.2 (*TimeOuts 2) The maximum on-hook time for identifying it as a Hook Flash. Integer 0-2,000 (milliseconds) *DisconnectTimeOut 710.3.4.3.3.
Appendix C MIB Parameter (Location in Parenthesis) C-45 Description Values *TrapToggle 710.3.3.14.5 (*Traps 5) An On/Off toggle status, indicating a change in status from off to on or vice versa. Integer on (1) off (2) *LastAUMacAddress 710.3.3.14.6 (*Traps 6) Applicable to SU only. The MAC address of the last AU with which the SU was associated. MAC address *TrapLog 710.3.3.14.7 (*Traps 7) Login or logout to the monitor program via the Monitor port or Telnet.
BreezeACCESS Version 4.3 System Manual C-46 Traps Trap (Number) Description Variables *SUassociatedAUTRAP(2) An AU trap indicating a new association with an SU. *TrapSUMacAddr *AUdisassociatedTRAP(3) An AU trap indicating that an SU has been disassociated from the AU. The AU decides that an SU has been disassociated from it and remove it from the ADB after receiving from another AU a SNAP frame with the SU MAC address.
Appendix C C-47 Trap (Number) Description Variables *TrapAUAlarmsSeverity *NoAssociationsOnTRAP (201) An IF-based AU alarm. Alarm was set on: The AU was reset 3 consecutive times as a result of no association with any SU, and before that the AU was associated with at least Minimum Number Of SUs. *NoAssociationsOffTRAP (202) Alarm was set off: At least one SU became associated with the AU. The alarm will be set off also after activating Clear All Alarms or after disabling the AU Alarms Option.
BreezeACCESS Version 4.3 System Manual C-48 Trap (Number) Description Variables *HighRetransmissionsRateOnTRAP (209) Alarm was set on: Minor Severity Alarm: a. The Retransmissions Current Rate exceeds the Retransmissions Minor Alarm Threshold, and is higher than the Retransmissions Average Rate by at least Retransmissions Minor Alarm Minimum Delta. b.
Appendix C C-49 Trap (Number) Description Variables *HighCRCErrorRateOnTRAP (213) Alarm was set on: Minor Severity Alarm: a. The CRC Error Current Rate exceeds the CRC Error Minor Alarm Threshold, and is higher than the CRC Error Average Rate by at least CRC Error Minor Alarm Minimum Delta. b. The CRC Error Current Rate has dropped below the CRC Error Major Alarm Threshold but is still higher than the CRC Error Minor Alarm Threshold.
C-50 Manual Revision: 3.0 BreezeACCESS Version 4.
Appendix D: RSSI to dBm Conversion Table SU-A/E, AU-A/E RSSI 71 72 74 75 77 78 81 82 83 84 85 86 88 89 90 91 92 93 94 96 97 98 99 100 101 102 103 104 105 106 107 108 110 111 112 113 dBM -100 -99 -98 -97 -96 -95 -94 -93 -92 -91 -90 -89 -88 -87 -86 -85 -84 -83 -82 -81 -80 -79 -78 -77 -76 -75 -74 -73 -72 -71 -70 -69 -68 -67 -66 -65 RSSI 114 115 116 118 119 120 121 122 123 125 126 127 128 129 130 131 133 134 135 136 137 138 139 141 142 143 144 145 146 148 149 150 151 152 153 dBM -64 -63 -62 -61 -60 -59 -58 -
BreezeACCESS Version 4.3 System Manual D-2 SU-R and SU-I RSSI 26 27 29 30 32 33 35 36 38 39 41 42 44 45 47 48 50 51 53 54 56 57 59 60 62 63 65 66 68 69 71 72 74 75 77 78 Manual Revision: 3.
Appendix E: Parameters List Unit Control Parameters Parameter Unit Range Default Run-Time Updated Change Unit Name All Up to 32 printable ASCII Empty String characters Yes Change Readonly Password All Up to 8 printable ASCII characters public Yes – For access from Monitor or Telnet only Change Installer Password All Up to 8 printable ASCII characters user Yes – For access from Monitor or Telnet only Change Administrator Password All Up to 8 printable ASCII characters private Yes – For
BreezeACCESS Version 4.
Appendix E E-3 Range Default RunTime Updated Parameter Unit Duplicate Frames Minor Alarm Minimum Delta IF-based AU 0 – 100 (%) 5 (%) Yes Duplicate Frames Minor Alarm Threshold IF-based AU 1 – 100 (%) 5 (%) Yes Duplicate Frames Major alarm Threshold IF-based AU 1 – 100 (%) 15 (%) Yes SU Rx Power Decrease Threshold IF-based AU 1 – 99 (dBm) 15 (dBm) Yes AU Rx Power Decrease Threshold IF-based AU 1 – 99 (dBm) 15 (dBm) Yes Minimum Number Of SUs IF-based AU 1 – 254 (SUs) 5 (SUs)
BreezeACCESS Version 4.
Appendix E E-5 Parameter Unit Range Receive SU-A/E (IF 0, 10dB, 25dB Attenuation Control based units) Default 0 Run-Time Updated No Maximum Data Rate AU, SU 1, 2 and 3Mbps 3Mbps No AU Transmission Rate Control SU Disable, Enable No Acknowledge Delay Limit AU, SU Low, Medium, Low High No Maximum Number of Associations AU 1 – 512 Yes Call Aging Time AU 1 (no aging), 2- 1800 seconds 50,000 (seconds) No Maximum Voice Sessions AU 0 – 50 12 Yes ACSE Option AU and GU Disable, En
BreezeACCESS Version 4.3 System Manual E-6 Parameter Unit Range Default ATPC Maximum Last Level Time After Synchronization Loss SU 0-3600 (seconds) Scanning Mode SU Active, Passive Active MAC Address Black List AU Send Roaming SNAP All SUs, except SU-BD, SU-BD1V Disable, Enable Wireless Trap Threshold AU, SU AU: 0 to 100 % AU: 30 % SU: 0 to 255 IF based SU: 95 RSSI units SU-R: 48 SU-I: 60 Manual Revision: 3.
Appendix E E-7 Network Management Parameters Parameter Unit Range Default RunTime Updated Access To Network Management AU, SU From Wlan Only, From Ethernet Only, From Both Ethernet & Wlan From Both Ethernet & Wlan No Network Management Filtering All Disable, Activate Management IP Filter On Ethernet Port, Activate Management IP Filter On Wlan Port (not available in GU), Activate Management IP Filter On Both Ethernet & Wlan Ports (not available in GU), Disable No Set Network Management IP A
BreezeACCESS Version 4.
Appendix E E-9 Bridge Parameters Parameter Unit VLAN ID-Data SU VLAN ID – Management Range 1 – 4094 Default Run-Time Updated 1 No AU, GU, 1 – 4094, 65535 SU without voice 65535 (no VLAN) No VLAN ID – Voice & Management SU with voice 1 – 4094, 65535 65535 (no VLAN) No VLAN Link Type AU, SU Hybrid Link, Trunk Link, Access Link (only in SU) Hybrid Link No Voice Priority Tag Option SU with voice Disable, Enable Disable No VLAN Forwarding Support AU, SU Disable, Enable Disable
BreezeACCESS Version 4.
Appendix E E-11 Performance Parameters Parameter Unit Range Default Run-Time Updated RTS Threshold AU, SU 20 – 1600 bytes AU: 1600 SU: 60 No Number of Retransmissions AU, SU 1 – 100 1 No Number of Retransmissions to Decrease Rate AU, SU 0 – 10 0 No Number of Dwells to Retransmit AU, SU 0–9 2 No Minimum Contention Window AU, SU 7 - 255 31 No Carrier Sense Level AU, SU -100 to -40 (dBm) -85 dBm No Maximum Multicast Rate AU 1, 2, 3Mbps 1Mbps Yes Multi-Rate Support AU,
BreezeACCESS Version 4.3 System Manual E-12 Service Parameters Parameter Unit Range Default RunTime Updated User Filtering Option SU Disable, IP Only, User Defined Addresses Only, PPPoE Protocol Only Disable Yes Set User Filter Address SU IP address (8 entries) 0.0.0.0 (all 8 entries) Yes Set User Filter Mask SU IP address (8 entries) 255.255.255.
Appendix E E-13 RADIUS Parameters Parameter Unit Range Default RunTime Updated User Name SU Up to 64 printable ASCII characters The units’ MAC Address No User Password SU Up to 64 printable ASCII characters RadiusPassword1 No Shared Secret SU Up to 20 characters RadiusSecret1234 No Authentication Option SU Disable, enable Disable No RADIUS Server SU Authentication IP Address IP Address 0.0.0.
BreezeACCESS Version 4.
Appendix E E-15 Dialing Parameters Parameter Unit Range Default RunTime Updated Pulse Dialing SU with voice Disable, Enable Enable No Gatekeeper Option SU with voice Disable, Enable Disable No Gatekeeper / Gateway IP Address SU with voice IP address 0.0.0.0 No Alternate Gatekeeper Option SU with voice Disable, Enable Disable No Alternate Gatekeeper IP Address SU with voice IP address 0.0.0.
BreezeACCESS Version 4.3 System Manual E-16 Parameter International Prefix Unit SU with voice Range Default RunTime Updated One phone key-pad digit 0 (0-9, *, #, A, B, C, D) and X (no prefix).
Appendix E E-17 Telephony Signals Parameter Unit Range Default RunTime Updated Telephony SU with Country Standard voice Proprietary, Germany, Sweden, France, United Kingdom, Belgium, USA, Chile USA No Frequency 1 SU with voice 0 – 3000Hz Dial Tone: 350 No Ring Back: 440 Busy: 480 Congestion: 480 Error: 480 High Level Error: 20 Frequency 1 SU with voice 0 – 3000Hz Dial Tone: 350 No Ring Back: 440 Busy: 480 Congestion: 480 Error: 480 High Level Error: 0 Ring Frequency: 20 Level 1 SU with
BreezeACCESS Version 4.
Appendix E E-19 Hopping Parameters Parameter Unit Range Default RunTime Updated Number of Hopping Frequencies GU 2-151 No Automatic Recovery Option GU Disable, Enable Enable Yes Automatic Recovery Interval GU 5 – 1440 (minutes) 15 (minutes) Yes ACSE Option AU and GU Disable, Enable Disable No Dwell Time AU and GU 32, 64, 128 128 No Alarm Parameters Parameter Unit Range Default RunTime Updated Alarm In Names GU Up to 31 printable ASCII Alarm In 1 characters through Alar
E-20 Manual Revision: 3.0 BreezeACCESS Version 4.
Appendix F: Hopping Sequences Hopping Standard: Australia Each hopping sequence is comprised of 60 channels in the frequency band from 2402 MHz to 2461 MHz (channels 2 to 80).
BreezeACCESS Version 4.3 System Manual F-2 Actual Frequency: (2400+Channel) MHz Calculating the operational hopping sequence: IF [Pi(1, 1)+(S-1)x3+(H-1)]>61, than Pi(H, S) = Pi(1, 1)+(S-1)x3+(H-1)-60, else Pi(H, S) = Pi(1, 1)+(S-1)x3+(H-1) Where: S=Hopping Set. Range: 1-3 H=hopping Sequence. Range: 1-20 i =Index. Range: 1-60 Pi(H, S) = Channel with index i in operational sequence with Hopping Set S and Hopping sequence H.
Appendix F F-3 Hopping Standards: Canada, Mexico Each hopping sequence is comprised of 30 channels in the frequency band from 2452 MHz to 2481 MHz (channels 2 to 80).
BreezeACCESS Version 4.3 System Manual F-4 Hopping Standards: Europe ETSI, US FCC, International Each hopping sequence is comprised of 79 channels in the frequency band from 2402 MHz to 2480 MHz (channels 2 to 80).
Appendix F F-5 Calculating the operational hopping sequence: IF [Pi(1, 1)+(S-1)x3+(H-1)]>80, than Pi(H, S) = Pi(1, 1)+(S-1)x3+(H-1)-79, else Pi(H, S) = Pi(1, 1)+(S-1)x3+(H-1) Where: S=Hopping Set. Range: 1-3 H=hopping Sequence. Range: 1-26 i =Index. Range: 1-79 Pi(H, S) = Channel with index i in operational sequence with Hopping Set S and Hopping sequence H. Pi(1, 1) = Channel with index i in the basic sequence (Hopping Set 1, Hopping sequence 1). BreezeACCESS Version 4.
BreezeACCESS Version 4.3 System Manual F-6 Hopping Standards: France Each hopping sequence is comprised of 35 channels in the frequency band from 2448 MHz to 2482 MHz (channels 28 to 82).
Appendix F F-7 Hopping Standards: Israel Each hopping sequence is comprised of 35 channels in the frequency band from 2421 MHz to 2455 MHz (channels 21 to 55).
BreezeACCESS Version 4.3 System Manual F-8 Hopping Standards: Japan Each hopping sequence is comprised of 23 channels in the frequency band from 2473 MHz to 2495 MHz (channels 73 to 95). Calculating the operational hopping sequence: Step Size D is defined as D(H, S) = 6 + (S-1) x 3 + (H-1) Where: S=Hopping Set. Range: 1-3 H=hopping Sequence. Range: 1-4 D(H, S) = Step Size for Hopping Set H and Hopping Sequence S.
Appendix F F-9 P17(1, 3) = [(17-1) x 12]mod23 + 73 = 192 mod23 + 73 = 8 + 73 = 81 P18(1, 3) = [(18-1) x 12]mod23 + 73 = 204 mod23 + 73 = 20 + 73 = 93 P19(1, 3) = [(19-1) x 12]mod23 + 73 = 216 mod23 + 73 = 9 + 73 = 82 P20(1, 3) = [(20-1) x 12]mod23 + 73 = 228 mod23 + 73 = 21 + 73 = 94 P21(1, 3) = [(21-1) x 12]mod23 + 73 = 240 mod23 + 73 = 10 + 73 = 83 P22(1, 3) = [(22-1) x 12]mod23 + 73 = 252 mod23 + 73 = 22 + 73 = 95 P23(1, 3) = [(23-1) x 12]mod23 + 73 = 264 mod23 + 73 = 11 + 73 = 84 Hopping sequence chann
BreezeACCESS Version 4.3 System Manual F-10 Hopping Standards: Korea Each hopping sequence is comprised of 23 channels in the frequency band from 2430 MHz to 2452 MHz (channels 30 to 52) Calculating the operational hopping sequence: Step Size D is defined as D(H, S) = 6 + (S-1) x 3 + (H-1) Where: S=Hopping Set. Range: 1-3 H=hopping Sequence. Range: 1-4 D(H, S) = Step Size for Hopping Set H and Hopping Sequence S.
Appendix F F-11 P17(1, 3) = [(17-1) x 12]mod23 + 30 = 192 mod23 + 30 = 8 + 30 = 38 P18(1, 3) = [(18-1) x 12]mod23 + 30 = 204 mod23 + 30 = 20 + 30 = 50 P19(1, 3) = [(19-1) x 12]mod23 + 30 = 216 mod23 + 30 = 9 + 30 = 39 P20(1, 3) = [(20-1) x 12]mod23 + 30 = 228 mod23 + 30 = 21 + 30 = 51 P21(1, 3) = [(21-1) x 12]mod23 + 30 = 240 mod23 + 30 = 10 + 30 = 40 P22(1, 3) = [(22-1) x 12]mod23 + 30 = 252 mod23 + 30 = 22 + 30 = 52 P23(1, 3) = [(23-1) x 12]mod23 + 30 = 264 mod23 + 30 = 11 + 30 = 41 Hopping sequence chan
BreezeACCESS Version 4.3 System Manual F-12 Hopping Standards: Spain Each hopping sequence is comprised of 27 channels in the frequency band from 2447 MHz to 2473 MHz (channels 47 to 73).
Index 1-1 Index A Access Link Parameter Access to DHCP Parameter Access to Network Management Parameter Access Units AU-A/E-NI Accounting Interval Accounting Option Accounting Parameters Menu Acknowledge Delay Limit Parameter ACSE Number Of Retransmissions For Data Parameter ACSE Number Of Retransmissions For Voice Parameter ACSE Option ACSE Option Parameter ACSE Parameters Parameter Add Forwarding VLAN ID Parameter Add Relaying VLAN ID Parameter Advanced Configuration Menu Air Interface Parameters Air In
1-2 AU Rx Power Decrease Threshold Parameter AU Transmission Rate Control (SU only) AU-A/E-BS Packing List AU-A/E-NI Packing List AU-I/I-D Installation Packing List AU-NI Installation Authentication Algorithm Parameter Authentication Option Authentication Parameters Menu Automatic Alarms Out Definition Menu Automatic Prefix Parameter Automatic Recovery Interval Automatic Recovery Option B Bad fragments received Parameter Base Station Equipment Basic Configuration Menu Battery Polarity Parameter Best AU Par
Index 1-3 Packing List Busy Tone Parameter . Book 2, 1-2 ..
1-4 Defaults Settings Parameter Delete a Network Management IP Address Parameter Delete a User Filtering Entry Parameter Delete All Network Management IP Addresses Parameter Delete All User Filtering Entries Parameter Destination IP Address Parameter DHCP Broadcast Override Filter Parameter DHCP Client Parameter DHCP Options Parameter Dial Tone Parameter Dialing Parameters Dialing Parameters Menu Dialing Prefix Option Parameter Dialing Prefix Parameter Disconnect Timeout Parameter Display Association Info
Index 1-5 Filter Options Parameter Flash Memory Control Parameter Flash Type Parameter Flash Versions Parameter Frames dropped (too many retries) Parameter Frequency 1 Parameter Frequency 2 Parameter G G711A-law Frames Per Packet Parameter G711u-law Frames Per Packet Parameter G723 Frames Per Packet Parameter G729 Frames Per Packet Parameter Gatekeeper Option Parameter GateKeeper/GateWay IP Address Parameter General RADIUS Parameters Menu GPS and Alarms System Installation GPS and Alarms system Graceful D
1-6 I Info Screens Menu Information Transfer Capability Parameter Installation AU-I/I-D Connecting the Antenna Cable GU-A-BS GPS and Alarms System Indoor Units Modular Base Station Equipment Outdoor Units Pole Mounting Outdoor Units SU-I/I-D SU-NI and AU-NI SU-R SU-R Guidelines Installation Guidelines SU-I/I-D Inter-Digit Timeout Parameter Interference Avoidance Parameters Internally discarded MIR/CIR Parameter International Prefix Parameter Inter-Regional Prefix Parameter Introducing BreezeACCESS IP Addre
Index 1-7 MAC Address Database Main Menu Management Systems BreezeCONFIG BreezeMANAGE Max.
1-8 Minimum Contention Window Parameter Minimum Number Of SUs Minimum RSSI Level MIR - AU to SU Parameter MIR - SU to AU Parameter MIR and CIR Parameters MIR/CIR Option Parameter Multi-Rate Decision Window Size Parameter Multi-Rate Support Parameter BreezeACCESS Version 4.3 Index ...Book 4, 2-70 ...Book 4, 2-27 ...Book 4, 2-46 ...Book 4, 2-75 ...Book 4, 2-75 ...Book 4, 2-74, Book 4, 2-89, Book 4, 2-90 ...Book 4, 2-75 ...Book 4, 2-71 ...
Index 1-9 SU-R Per Hop Statistics Per Trap Control Performance Parameters Performance Parameters Menu Per-Rate Counters Physical Specifications Ping Frame Length Parameter Ping Frame Timeout Parameter Ping Test Ports Control Parameter Power Level Parameter PPPoE Broadcast Override Filter Parameter Precautions Preferred AU MAC Address Parameter Pulse Dialing Parameter . Book 2, 2-2 ..Book 4, 2-18 ..Book 4, 2-55 ..Book 4, 2-69 ..Book 4, 2-69 ..Book 4, 2-23 ..Book 1, 3-7 ..Book 4, 2-19 ..Book 4, 2-19 ..
1-10 Send AU Wireless Quality Trap Send GPS Alarm In Trap Send GPS Alarm Out Trap Send Monitor Status Trap Send Parameter Changed Trap Send Power Up From Reset Trap Send Roaming SNAP Send SNMP Traps Parameter Send SU Associated AU Trap Send SU Associated Trap Send UTC Status Trap Service Parameters Service Parameters Menu Set Factory Defaults Parameter Set Full Operator Defaults Parameter Set Network Management IP Addresses Parameter Set Partial Factory Defaults Parameter Set Partial Operator Defaults Para
Index 1-11 Radio and Modem Standards Compliance, General SU-A/E SU-I/I-D SU-R Telephony Voice/Fax Start Sending Parameter Statistics Per Hop Traffic Voice Stop Sending Parameter SU Rx Power Decrease Threshold Parameter SU-A/E Aligning Antenna Packing List Subnet Mask Parameter Subscriber Units SU-A/E SU-R SU-I Positioning Antennas SU-I/I-D Installation Installation Guidelines Packing List SU-I-D Aligning External Antennas SU-NI Installation Support All (AU only) SU-R Aligning External Antenna Installation
1-12 Ping Test Cycle Parameter Timeouts Parameter ToS Precedence Threshold Parameter ToS Priority Parameter ToS Priority Parameters Total received data frames Parameter Total received frames from wireless Parameter Total received frames via Ethernet Parameter Total retransmitted frames Parameter Total submitted frames (bridge) Parameter Total transmitted frames to wireless Parameter Total Tx errors Parameter Traffic Statistics Transmit Antenna Parameter Transmit Power Control Algorithm Transmit Power Contr
Index 1-13 User Name User Password ..Book 4, 2-78 ..
1-14 Manual Revision: 3.0 BreezeACCESS Version 4.
