User's Manual
Table Of Contents
- System Manual BreezeMAX Extreme
- About This Manual
- Contents
- Chapter 1 - System Description
- 1.1 About WiMAX
- 1.2 WiMAX Network Architecture
- 1.3 BreezeMAX Extreme
- 1.4 Specifications
- 1.4.1 General Modem and Radio
- 1.4.2 3.x GHz BTS
- 1.4.3 5 GHz BTS
- 1.4.4 Sensitivity
- 1.4.5 3.x GHz Antennas
- 1.4.6 5 GHz Antennas
- 1.4.7 Power Supply
- 1.4.8 GPS Antennas
- 1.4.9 Data Communication (Ethernet Port)
- 1.4.10 Configuration and Management
- 1.4.11 Environmental
- 1.4.12 BTS Standards Compliance, General
- 1.4.13 Notes on Maximum Tx Power Limitations for 5 GHz Units Using FCC Country Code:
- 1.4.14 TDWR Interference Avoidance
- Chapter 2 - Installation
- 2.1 Site Deployment Options
- 2.2 BTS Installation
- 2.3 GPS Installation
- 2.4 Indoor Power Supply Installation
- 2.5 Cable Connections
- 2.6 External Antennas Connection
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- 4.1 BreezeMAX Extreme System Management
- 4.2 The Monitor Program
- 4.3 IP Addresses Configuration
- 4.4 The Main Menu
- 4.5 BTS Menu
- 4.5.1 Show Summary
- 4.5.2 Show Properties
- 4.5.3 Show License Properties
- 4.5.4 Configuration
- 4.5.5 Unit Control
- 4.5.6 Fault Management
- 4.5.7 Performance Counters
- 4.6 ASN-GW Menu
- 4.6.1 AAA
- 4.6.2 Services Menu
- 4.6.2.1 Introduction
- 4.6.2.2 Common Operations in Services Menus
- 4.6.2.3 MSs Services
- 4.6.2.4 Service Profiles
- 4.6.2.5 QoS Profiles
- 4.6.2.6 Multiple Service Flows
- 4.6.2.7 Service Rules
- 4.6.2.8 Classifiers
- 4.6.2.9 Service Groups
- 4.6.2.9.1 Service Group ID
- 4.6.2.9.2 Service Group Name
- 4.6.2.9.3 DHCP Type
- 4.6.2.9.4 Nomadic Mode
- 4.6.2.9.5 Attribute 31
- 4.6.2.9.6 Attribute 32
- 4.6.2.9.7 Attribute 32 Free Text
- 4.6.2.9.8 Interface IP Address
- 4.6.2.9.9 Interface Subnet Mask
- 4.6.2.9.10 Default Gateway
- 4.6.2.9.11 VLAN ID
- 4.6.2.9.12 VLAN Priority
- 4.6.2.9.13 DHCP Server Specific Parameters
- 4.6.2.9.14 Option 82 Parameters
- 4.6.2.9.15 DHCP Relay with Option 82 Specific Parameters
- 4.6.2.9.16 Show DHCP Lease Times
- 4.6.2.10 Service Interfaces
- 4.6.2.10.1 Service Interface ID
- 4.6.2.10.2 Service Interface Name
- 4.6.2.10.3 Forwarding Rule Name
- 4.6.2.10.4 CS Type
- 4.6.2.10.5 VLAN Interface
- 4.6.2.10.6 VLAN Transparency
- 4.6.2.10.7 VLAN ID
- 4.6.2.10.8 VLAN Priority Marking
- 4.6.2.10.9 VLAN Priority
- 4.6.2.10.10 VLAN List
- 4.6.2.10.11 Inner DSCP Marking
- 4.6.2.10.12 Inner DSCP
- 4.6.2.11 Forwarding Rules
- 4.6.2.12 MSs Default Services
- 4.6.3 MAC Access Lists
- 4.7 Sector Menu
- 4.8 BS Menu
- 4.9 Radio Channel Menu
- 4.10 Antenna Menu
- 4.11 GPS Menu
- 4.12 MS Menu
- 4.13 Parameters Summary
- Glossary
Chapter 4 - Operation and Administration ASN-GW Menu
BreezeMAX Extreme 147 System Manual
The available options are None, CPE MAC Address and CPE Fully Qualified
Domain Name.
In Relay with Option 82 mode, at least one Sub Type (either 1 or 2) must be other
than None (a combination where both Sub Type 1 and Sub Type 2 are None is not
allowed).
The default option is CPE MAC Address.
4.6.2.9.15 DHCP Relay with Option 82 Specific Parameters
The following parameters, specifying the parameters to be used for
communicating with a DHCP server, are applicable only for Service Groups with
DHCP Type Relay with Option 82:
4.6.2.9.15.1 DHCP IP Address
The DHCP IP address is the intended DHCP server to be used. The IP must not be
included in other IP ranges used by other Service Groups, in IP Pools or other IP
ranges used by the ASN.
4.6.2.9.15.2 GI IP Address
DHCP gateway (relay agent) IP address included in DHCP messages. This is the IP
address used for communication with the external DHCP server. Must be in the
same subnet as the Default Gateway. Must not be in use by another Service
Group (as GIADDR for DHCP Relay or server IP for DHCP Server Service Group).
The default is the Management Interface IP Address. In this case all other relevant
parameters (Interface Subnet Mask, Default Gateway, VLAN ID) must be the
default values (Management Interface parameters).
4.6.2.9.15.3 Subnet Mask
The subnet mask used with the GI IP Address. The default used with the default
GI IP Address is the Management Interface Subnet Mask.
4.6.2.9.16 Show DHCP Lease Times
Select this option to view per DHCP Server Service Group all the binding details
for each client: IP Address, Client MAC Address, Expiration Time, MS KEY ID,
Serving BS ID, and Connection Type.
4.6.2.10 Service Interfaces
The Service Interface menu enables managing the parameters of the interface
used by the ASN on the network side for a service using a specific Service
Interface. Up to 1024 different Service Interfaces can be defined.
Each Service Interface includes the following parameters: