User Manual
Table Of Contents
- BreezeMAX® Extreme
- System Manual
- About This Manual
- Contents
- System Description
- 1.1 About WiMAX
- 1.2 WiMAX Network Architecture
- 1.3 BreezeMAX Extreme
- 1.4 Specifications
- 1.4.1 General Modem & Radio
- 1.4.2 3.x GHz BTS
- 1.4.3 5 GHz BTS
- 1.4.4 Sensitivity
- 1.4.5 3.x GHz Antennas
- 1.4.6 5 GHz Antennas
- 1.4.7 Power Supply
- 1.4.8 GPS Antennas
- 1.4.9 Data Communication (Ethernet Port)
- 1.4.10 Configuration and Management
- 1.4.11 Environmental
- 1.4.12 BTS Standards Compliance, General
- 1.4.13 Notes on Maximum Tx Power Limitations for 5 GHz Units:
- Installation
- 2.1 BTS Installation
- 2.2 GPS Installation
- 2.3 Indoor Power Supply Installation
- 2.4 Cable Connections
- 2.5 External Antennas Connection
- Commissioning
- Operation and Administration
- 4.1 BreezeMAX Extreme System Management
- 4.2 The Monitor Program
- 4.3 IP Addresses Configuration
- 4.4 The Main Menu
- 4.5 BTS Menu
- 4.5.1 Show Summary
- 4.5.2 Show Properties
- 4.5.3 Configuration
- 4.5.4 Unit Control
- 4.5.5 Fault Management
- 4.5.6 Performance Counters
- 4.6 ASN-GW Menu
- 4.6.1 AAA
- 4.6.2 Services Menu
- 4.6.2.1 Common Operations in Services Menus
- 4.6.2.2 MSs Services
- 4.6.2.3 Service Profiles
- 4.6.2.4 QoS Profiles
- 4.6.2.5 Multiple Service Flows
- 4.6.2.6 Service Rules
- 4.6.2.7 Classifiers
- 4.6.2.8 Service Groups
- 4.6.2.9 Service Interfaces
- 4.6.2.9.1 Service Interface ID
- 4.6.2.9.2 Service Interface Name
- 4.6.2.9.3 Forwarding Rule Name
- 4.6.2.9.4 CS Type
- 4.6.2.9.5 VLAN Interface
- 4.6.2.9.6 VLAN Transparency
- 4.6.2.9.7 VLAN ID
- 4.6.2.9.8 VLAN Priority Marking
- 4.6.2.9.9 VLAN Priority
- 4.6.2.9.10 VLAN List
- 4.6.2.9.11 Inner DSCP Marking
- 4.6.2.9.12 Inner DSCP
- 4.6.2.10 Forwarding Rules
- 4.7 Sector Menu
- 4.8 BS Menu
- 4.9 Radio Channel Menu
- 4.10 Antenna Menu
- 4.11 GPS Menu
- 4.12 MS Menu
- 4.13 Parameters Summary
- Glossary
Chapter 4 - Operation and Administration GPS Menu
BreezeMAX Extreme 168 System Manual
4.11.2.2.3 External 10MHz Clock
The 10MHz clock source is used for generation of all main clocking signals in the
system, including the internal 1PPS clock when GPS Type is set to None or when
the GPS receiver does not function properly.
For a Master unit the default External 10MHz Clock is Disable (use internal clock
source).
For Slave units the default External 10MHz Clock is Enable (derived from the
previous unit in the chain).