User Manual
Table Of Contents
- BreezeMAX® Extreme
- System Manual
- About This Manual
- Contents
- System Description
- 1.1 About WiMAX
- 1.2 WiMAX Network Architecture
- 1.3 BreezeMAX Extreme
- 1.4 Specifications
- 1.4.1 General Modem & Radio
- 1.4.2 3.x GHz BTS
- 1.4.3 5 GHz BTS
- 1.4.4 Sensitivity
- 1.4.5 3.x GHz Antennas
- 1.4.6 5 GHz Antennas
- 1.4.7 Power Supply
- 1.4.8 GPS Antennas
- 1.4.9 Data Communication (Ethernet Port)
- 1.4.10 Configuration and Management
- 1.4.11 Environmental
- 1.4.12 BTS Standards Compliance, General
- 1.4.13 Notes on Maximum Tx Power Limitations for 5 GHz Units:
- Installation
- 2.1 BTS Installation
- 2.2 GPS Installation
- 2.3 Indoor Power Supply Installation
- 2.4 Cable Connections
- 2.5 External Antennas Connection
- Commissioning
- Operation and Administration
- 4.1 BreezeMAX Extreme System Management
- 4.2 The Monitor Program
- 4.3 IP Addresses Configuration
- 4.4 The Main Menu
- 4.5 BTS Menu
- 4.5.1 Show Summary
- 4.5.2 Show Properties
- 4.5.3 Configuration
- 4.5.4 Unit Control
- 4.5.5 Fault Management
- 4.5.6 Performance Counters
- 4.6 ASN-GW Menu
- 4.6.1 AAA
- 4.6.2 Services Menu
- 4.6.2.1 Common Operations in Services Menus
- 4.6.2.2 MSs Services
- 4.6.2.3 Service Profiles
- 4.6.2.4 QoS Profiles
- 4.6.2.5 Multiple Service Flows
- 4.6.2.6 Service Rules
- 4.6.2.7 Classifiers
- 4.6.2.8 Service Groups
- 4.6.2.9 Service Interfaces
- 4.6.2.9.1 Service Interface ID
- 4.6.2.9.2 Service Interface Name
- 4.6.2.9.3 Forwarding Rule Name
- 4.6.2.9.4 CS Type
- 4.6.2.9.5 VLAN Interface
- 4.6.2.9.6 VLAN Transparency
- 4.6.2.9.7 VLAN ID
- 4.6.2.9.8 VLAN Priority Marking
- 4.6.2.9.9 VLAN Priority
- 4.6.2.9.10 VLAN List
- 4.6.2.9.11 Inner DSCP Marking
- 4.6.2.9.12 Inner DSCP
- 4.6.2.10 Forwarding Rules
- 4.7 Sector Menu
- 4.8 BS Menu
- 4.9 Radio Channel Menu
- 4.10 Antenna Menu
- 4.11 GPS Menu
- 4.12 MS Menu
- 4.13 Parameters Summary
- Glossary
Chapter 4 - Operation and Administration ASN-GW Menu
BreezeMAX Extreme 120 System Manual
4.6.2.9.6 VLAN Transparency
Applicable only in Ethernet CS (with VLAN Interface enabled). In IP CS it is always
set to Disable.
If set to Enable: Uplink and downlink packets whose VLAN IDs are included in the
VLAN List (see below) will be forwarded transparently without any changes in the
value of the VLAN ID. All other packets will be discarded. The VLAN Priority of
uplink packets may be changed, depending on the configured VLAN Priority
Marking parameter.
If set to Disable: In the uplink packets will be forwarded with a VLAN tag with the
values defined by the VLAN ID and VLAN Priority parameters (replacing original
VLAN tag or added to untagged packets). If the VLAN ID is set to None (untagged),
all uplink packets will be forwarded untagged. In the downlink a reverse process
will take place according to the what was learned in the uplink.
4.6.2.9.7 VLAN ID
In IP CS the VLAN ID parameter is applicable only if VLAN Interface is set to
Enable. In Ethernet CS applicable only if VLAN Transparency is set to Disable.
This is the VLAN ID to be inserted in packets forwarded to the network (uplink).
The available range is 1-4094 or 4096 for untagged. To set the value to 4096
(none) you can also click Enter with an empty (null) string.
4.6.2.9.8 VLAN Priority Marking
Applicable only in Ethernet CS when VLAN Transparency is set to Enable. If VLAN
Priority Marking is set to Disable, the VLAN Priority of forwarded packets will not
change. If set to Enable, the VLAN Priority of all forwarded tagged packets will be
replaced by the value configured for the VLAN Priority parameter.
4.6.2.9.9 VLAN Priority
In IP CS the VLAN Priority parameter is applicable only if VLAN ID is other than
None (untagged). The VLAN Priority to be inserted in packets forwarded to the
network (uplink).
In Ethernet CS, if VLAN Transparency is set to Disable and VLAN ID is other than
None, this is the VLAN Priority to be used in the uplink. If VLAN Transparency is
set to Enable and VLAN Priority Marking is set to Enable, the VLAN Priority of all
forwarded tagged packets will be replaced by this value.
The available range is from 0 to 7.
4.6.2.9.10 VLAN List
Applicable only in Ethernet CS when VLAN Transparency is set to Enable. A list of
up to 16 VLAN IDs (including None for untagged). Only packets with a VLAN ID
included in the list will be forwarded. An empty list means that all VLAN IDs