User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
breezeAccessVLMib
MIB Parameter Description Value/Range
*AdbAd Option
(*AUAdb 6)
Applicable to AU/BU. Read-
only. The current Adaptive
Modulation Option of the
relevant SU/RB.
Integer
disable (1),
enable (2),
na(255)
apMod
Entry 3
*AdbBurstModeOption
(*AUAdbEntry 37)
Applicable to AU/BU. Read-
only. The current Burst Mode
Option of the relevant SU/RB.
Integer
disable (1),
enable (2),
na(255)
*AdbConcatenationOption
(*AUAdbEntr
Applicable to AU/BU. Read-
only. The current
Concatenation Option of the
ant SU/RB.
Integer
disable (1),
enable (2),
55)
y 39)
relev na(2
*AdbSecurityMode le to AU/BU.
only. The current Security
evant SU/RB.
er
wep (1),
255)
(*AUAdbEntry 41)
Applicab Read- Integ
Mode of the rel aes (2),
na(
*AdbAuthOption
y 42)
AU/BU. Read-
only. The current
Authentication Algorith
ant SU/RB
Integer
nSystem(1),
redKey (2),
na(255)
(*AUAdbEntr
Applicable to
m
ope
sha
Option of the relev .
*AdbDataEncryptOption
(*AUAdbEntry 43)
/BU.
rrent Data
tion of th
.
Integer
disable (1),
enable (2),
55)
Applicable to AU
only. The cu
Read-
Encryption Op
relevant SU/RB
e
na(2
*AdbAge
(*AUAdbEntry 44)
/BU.
co
ivin
eva
Applicable to AU
only. The time in se
elapsed since rece
Read- Integer
nds
g the last
packet from the rel
SU/RB.
nt
*AdbUnitName
(*AUAdbEntry 45)
Applicable to AU/BU.
only. The Unit Name o
relevant SU/RB.
splayString Read-
f the
Di
*UpLinkQualityIndicator
6)
ato
abl
(*SiteSurvey
UpLink quality Indic
parameters. Applic
SU/RB.
r (LQI)
e only to
*MeasureUpLinkQualityIndic
ualityIndicator 1)
ator .
he
e for a period
s.
er
start (1),
cancel (2)
(*UpLinkQ
Applicable to SU/RB
calculation of LQI. T
calculation will b
Starts
Integ
of 10 second
*ReadUpLinkQualityIn
(*UpLinkQualityIndicato
dicator
r 2)
SU/RB. Read-
ults of the .
Applicable to
only. The res last LQI
Integer
1-8
calculation.
*UpLinkQualityIndicatorStatus
alityIndicator 3)
O
d
ere are
n the range of
n levels,
evels
used.
s that the
cate the
since the available
range is limited - by HW (HW
Revision A), or by the
applicable parameters in the
country code, or by the
configurable Maximum
Modulation Level parameter.
Integer
fullTest (1),
limitedTest (2)
(*UpLinkQu
Applicable to SU/RB
Indicates the test con
fullTest means that th
no limitations o
available modulatio
and that all modulation l
from 1 to 8 can be
limitedTest indicate
results may not indi
true quality
nly.
itions.
*MacPinpoint
(*SiteSurvey 7)
Applicable to AU/BU. MAC
Pinpoint parameters.
BreezeACCESS 4900 System Manual
207