User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
Appendix E - Supported MIBS and Traps
MIB Parameter Description Value/Range
*AdbTxFailed ModLevel8
Applicable to AU/BU. Not
applicable to units with HW
nicast
g
ounter 32
(*AUAdbEntry 24)
revision A. Read-only. Counts
the total number of failures to
successfully transmit a u
frame intended to the SU
during a HW Retry cycle usin
modulation level 8.
C
*AdbCirTx
(*AUAdbEntry 25)
t
zeNET B
alue
r.
Integer Applicable to AU Only. No
applicable to Bree
products. Read-only. The v
configured in the relevant SU
for the CIR: Uplink paramete
*AdbMirTx
(*AUAdbEntry 26) ed in
:
Integer
Applicable to AU/BU. Read-
only. The value configur
the relevant SU for the MIR
Uplink parameter.
*AdbCirRx
(*AUAdbEntry 27)
for the CIR: Downlink
parameter.
Integer Applicable to AU. Not
applicable to BreezeNET B
products. Read-only. The value
configured in the relevant SU
*AdbMirRx
(*AUAdbEntry 28)
Applicable to AU/BU. Read-
only. The value configured in
the relevant SU for the MIR:
Downlink parameter.
Integer
*AdbCirMaxDelay
(*AUAdbEntry 29)
Applicable to AU. Not
applicable to BreezeNET B
products. Read-only. The value
configured in the relevant SU
for the Maximum Delay
parameter.
Integer
*AdbDistance
(*AUAdbEntry 30)
Applicable to AU/BU. Read-
only. The measured distance
between the relevant SU/RB
and the AU/BU (In Kilometers).
Integer
1 means any
distance below
2 km
*AdbHwRevision
(*AUAdbEntry 31)
Applicable to AU/BU. Read-
only. The HW Revision of the
relevant SU/RB.
Integer
HwRevisionA
(1),
HwRevisionB
(2),
HwRevisionC
(3),
na(255)
*AdbCpldVer
(*AUAdbEntry 32)
Applicable to AU/BU. Read-
only. The CPLD Version of the
relevant SU/RB.
DisplayString
*AdbCountryCode
(*AUAdbEntry 33)
Applicable to AU/BU. Read-
only. The Country Code of the
relevant SU/RB.
Integer
*AdbBootVer
(*AUAdbEntry 34)
Applicable to AU/BU. Read-
only. The Boot Version of the
relevant SU/RB.
DisplayString
*AdbAtpcOption
(*AUAdbEntry 35)
Applicable to AU/BU. Read-
only. The current ATPC Option
of the relevant SU/RB.
Integer
disable (1),
enable (2),
na(255)
BreezeACCESS 4900 System Manual
206