User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
Appendix E - Supported MIBS and Traps
MIB Parameter Description Value/Range
*BurstModeOption
(*BurstMode 1)
Applicable to all units.
Applicable only if Burst Mode
Option is supported by the
Band. Enabling/disabling burs
mode operation. blocked (3)
value is returned when trying to
enable Burst Mode when it
should not be used due to the
configuration of certain other
parameters. These limitation
depend on HW revi
Sub-
t
s
sion and
unit type.
disable (1)
enable (2)
blocked (3)
na (255)
Integer
*BurstInterval
(*BurstMode 2)
Applicable to all units. The burst
interval in milliseconds.
Integer
1-the maximum
value as defined
in the Sub-Band.
)
na (255)
(milliseconds
*ConcatenationParameters
(*PerformanceParams 11)
Concatenation Parameters.
Applicable to all units.
*ConcatenationOption
(*ConcatenationParameters 1)
.
chanism.
Integer
disable (1)
enable (2)
a (255)
Applicable to all units
Enabling/disabling the
concatenation me
n
*ConcatenationMaximumNumberOfFrames Applicable to all units.
umber
Integer
(*ConcatenationParameters 2) Defines the maximum n
of data frames that can be
concatenated.
2 – 8
E.2.11 Site Survey Parameters
MIB Parameter Description Value/Range
*SiteSurvey
(breezeAccessVLMib 11)
*AverageReceiveSNR
(*SiteSurvey 1)
mes.
Applicable to SU/RB. Read-
only. The average Signal to
Noise Ratio of received fra
Integer
*TrafficStatistics
(*SiteSurvey 2)
Applicable to all units. Traffic
statistics parameters.
*ResetTrafficCounters
(*TrafficStatistics 1)
Applicable to all units. Resets
the traffic counters.
cancel (2)
Integer
reset (1)
*EthCounters
(*TrafficStatistics 2)
Applicable to all units. Ethernet
counters.
*TotalRxFramesViaEthernet
(*EthCounters 1)
Applicable to all units.
Read-only. Total number of
frames received via the
Ethernet port.
Counter 32
*TxWirelessToEthernet its.
er of
Counter 32
(*EthCounters 2)
Applicable to all un
Read-only. Total numb
frames transmitted to the
Ethernet port.
*WirelessLinkCounters
(*TrafficStatistics 3)
s Applicable to all units. Wireles
link counters.
*TxFramesToWireless
(*WirelessLinkCounters 1)
Transmitted frames counters
BreezeACCESS 4900 System Manual
198