User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
breezeAccessVLMib
E.2.9 Security Parameters
MIB Parameter De ription sc Value/Range
*SecurityParams
(breezeAccessVLMib 9)
*AuthenticationAlgorithm
(*SecurityParameters 1)
Applicable to all units.
Enables/disables the
authentication encryption
option.
openSystem: Authentication
messages are not encrypted.
sharedKey : Authentication
messages are encrypted.
Integ
open
share
er
System (1)
dKey (2)
*DefaultKey
(*SecurityParameters 2)
Applicable to SU/RB. The ID
of the key to be used for
encrypting/decrypting the
aut
Integer
Range: 1 to 4.
hentication messages.
*Da
(*Securit
App
Ena
enc
nteg
ble (1)
enable (2)
taEncryptionOption
yParameters 3)
licable to all units.
bles/disables the data
ryption option.
I
disa
er
*DefaultMulticastKey
(*S
App
of t
enc
mu
Integer
Range: 1 to 4. ecurityParameters 4)
licable to AU/RB. The ID
he key to be used for
rypting/decrypting
lticasts.
*Se
(*Securit
App
enc
use
me
enc
g
p
aesO
C
curityMode
yParameters 5)
licable to all units. The
ryption algorithm to be
Inte
we
d for authentication
ssages and/or data
ryption
aes
er
(1)
CB (2)
CM (3)
*PromiscuousAuthenticationMode
(*SecurityParameters 6)
App
Ena
pro
any
by
AU
g
b
enable (2)
licable to AU/RB.
bling/disabling the
miscuous mode, where
Inte
disa
SU can be authenticated
and communicate with the
.
er
le (1)
*Key1
(*SecurityParameters 7)
App
num
with ty
Stri
pas
isplayString
32 hexadecimal digits
licable to all units. Key
ber 1. Accessible only
D
SNMP Write Communi
ng (administrator
sword).
*Key2
(*SecurityParameters 8)
App
num
with
Stri
s
layString
hexadecimal digits
licable to all units. Key
ber 2. Accessible only
SNMP Write Community
ng (administrator
Disp
32
pa sword).
*Ke
(*S
pp
num
with
Stri
pas
spl
digits
y3 A
ecurityParameters 9)
licable to all units. Key
ber 3. Accessible only
SNMP Write Community
ng (administrator
sword).
Di
32 he
ayString
xadecimal
*Ke
(*S
App
num
with
Stri
pas
spl
he igits
y4
ecurityParameters 10)
licable to all units. Key
ber 4. Accessible only
SNMP Write Community
ng (administrator
sword).
Di
32
ayString
xadecimal d
BreezeACCESS 4900 System Manual
195