User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
breezeAccessVLMib
MIB Parameter Description Value/Range
*TcpPortRangeAdd
(*TcpPortRangeConfig 4)
Applicable to all units. Add
port range(s) to TCP Port
Rang
Get o rn an
empty g.
DisplayString
A range is defined by
<start> ,
where rt
Port of the range and <end>
is the End Port y
<start> ange
is <sta lue
sta re
ween 0 and 65535.
er can add several
using a comma to
parate between ranges.
pl ,99,987-900.
es Table.
eration will retup
strin
-<end> or <start>
start> is the Sta<
. If onl
is specified the r
rt>-<start>. The va
rt> and <end> aof <
bet
The us
ranges
se
Exam e: 10-26
*TcpPortRangeDelete
(*TcpPortRangeConfig 5)
Applic
Delet
TCP
Get o
empty
lay
rang
tart>-<end> or <start>,
here < the Start
d <end>
the E ly
the range
ta >. The value
of <sta re
between 0 and 65535.
The user can delete several
nges omma to
para n ranges.
Exampl 87-900.
able to all units.
e port range(s) from
Port Ranges Table.
peration will return an
Disp
A
<s
w
string. Port of the range an
is
String
e is defined by
start> is
nd Port. If on
<start>
is <s
is specified
rt>-<start
rt> and <end> a
ra
se
using a c
te betwee
e: 10-26,99,9
*TcpPortRangeDeleteAll
(*TcpPortRangeConfig 6)
Applic
Delet orm TCP
Port R
opera
Integer
deleteAll(1),
cancelO (2)
able to all units.
e all entries f
anges Table. Get
tion will return 1
peration
E.2.8 User Filtering Parameters
MIB Parameter Description Value/Range
*UserFilterParams
eezeAccessVLMib 8)
Applicable to SU/RB. User
filterin
(br g parameters.
*UserFilterOption
(*UserFilterParams 1)
Applic
Defin
option
disab
iPOnl
packe
userD
IP fra
define
pPPo
frame
teger
(2)
userDefinedAddrOnly (3)
PoE
(255
able to SU/RB.
es user-filtering
s.
le: No filtering.
In
disable (1)
ipOnly
y: Only IP protocol
ts pass.
efinedAddrOnly: Only
mes from/to user
d IP addresses pass.
pP
na
E Only: Only PPPoE
s pass.
Only (4)
)
*IpFilterTable
(*UserFilterParams 2)
Applic
table
addre
groups, to be u
User Filtering Option
(*UserFilterOption) is
userDefinedAddrOnly. Not
accessible.
able to SU/RB. A
of up to 8 user defined
sses, or address
sed if the
BreezeACCESS 4900 System Manual
193