User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
breezeAccessVLMib
MIB Parameter Description Value/Range
*DeltaFromMinSNRLevel
(*ATPC 2)
red
level,
4-20 (dB)
Applicable to AU/BU. The
Minimum SNR Level plus
the value of this parameter
define the maximum desi
level of the average SNR at
the AU/BU. If the ATPC
Option is enabled, than if
the received SNR is above
the maximum desired
the AU/BU will transmit
Power-Down messages to
the applicable SU/RB.
Integer
*MinimumSNRLevel
(*ATPC 3)
vel in dB of the
PC
Integer
4-60 (dB)
Applicable to AU/BU.
Defines the minimum
desired le
average SNR at the AU/BU.
Below this level, if ATPC
Option is enabled, the
AU/BU will transmit AT
Power-Up messages to the
applicable SU/RB.
*MinimumIntervalBetweenATPC
Messages
(*ATPC 4)
up/power-down messages.
Applicable to AU/BU. The
minimal time between
consecutive power-
Integer
Range: 1 to 3600 (seconds)
*PowerLevelSteps
(*ATPC 6)
Applicable to AU/BU. The
step in dB that the SU/RB
will use when receiving an
ATPC Power-Up/Power-
Down message
Integer
1-20 (dB)
*CellDistanceParameters
(*AirInterface 15)
s Cell distance Parameter
*CellDistanceMode
(*CellDistanceParameters 1)
The
automatic (1)
2)
)
Applicable AU/BU.
selected mode of deciding
on Cell Distance.
Integer
manual (
5na (25
*FairnessFactor
(*CellDistanceParameters 2)
tage of
that
Range: 0 to 100 (Percent). A
value of 0 means the
lot size (9
Applicable AU/BU. Not
applicable to BreezeNET B
products. The percen
the maximum distance
is taken into account in the
time slot calculation.
Integer
minimal s
microseconds).
Na (255)
*MeasuredMaxCellDistance
(*CellDistanceParameters 3) e as
calculated by the AU/BU.
2 km”.
Applicable AU/BU. The
Maximum Cell Distanc
Integer
Range: 0 to 54 (Kilometers).
1 means “below
*UnitWithMaxDistance
(*CellDistanceParameters 4)
Applicable AU only. Not
applicable to BreezeNET B
units. The MAC address of
the unit with the maximum
distance from the AU.
MAC Address
*ScanningMode
(*AirInterface 16)
Applicable to SU/RB. The
scanning mode. In cells
where the DFS Option is
enabled Scanning Mode is
forced to Passive.
Integer
passive (1)
active (2)
BreezeACCESS 4900 System Manual
185