User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
Appendix E - Supported MIBS and Traps
MIB Parameter Description Value/Range
*DFSChannelRe
(*DFSChannelReu
useOption
seParameters
1)
e DFS
Applicable to AU/BU.
Enabling/disabling th
Channel Reuse Algorithm.
Integer
disable (1)
enable (2)
na (255)
*DFSRadarActivityAssessmentPeri
od
(*DFSChannelReuseParameters
2)
AU/BU.
ity
Applicable to
The period in hours for
assessment of radar activ
when the Channel reuse
algorithm is enabled.
Integer
1 – 12 hours.
*DFSMaximumNumberOfDetection
seParameters
U/BU. The
f radar
e original
ching
Integer
– 10 detections.
sInAssessmentPeriod
(*DFSChannelReu
3)
Applicable to A
maximum number o
detection in th
channel during the Radar
Activity Assessment Period
that is required for rea
a decision to try again the
original channel.
1
*CountryCodeLearningBySU
(*FrequencyDefinition 12) eather the SU
Integer
disable (1)
2)
Applicable to AU only.
Defines w
should learn the country
code of the AU.
enable (
na (255)
*CurrentAUOperatingFrequencyNe
w
W
DisplayString
For 5.8 GHz products with
ion below 2.0 the
to 5830 MHz
Hz resolution.
with SW version
2.0 and up the range is as
n the selected Sub-
(*FrequencyDefinition 13)
Applicable to AU/BU. Read-
only. The operating
frequency in MHz.
(Replaces
*CurrentAUOperatingFreque
ncy to support a resolution
of 0.5 MHz for units with H
revision C and higher).
SW vers
range is 5740
using a 10 M
For units
defined i
Band.
*AUDefinedFrequencyNew
(*FrequencyDefinition 14)
Read-
sion below 2.0
se
n is
For 5.8 GHz products with
SW version below 2.0 the
5740 to 5830 MHz
Hz resolution.
ersion
2.0 and up the range is as
n the selected Sub-
Applicable to AU/BU.
only. For 5.8 GHz products
with SW ver
this is the frequency in MHz
of the AU/BU after the next
reset.
For units with SW version
2.0 and up this is the
frequency in MHz to u
when the DFS Optio
disabled. (Replaces
*AUDefinedFrequency to
support a resolution of 0.5
MHz for units with HW
revision C and higher).
DisplayString
range is
using a 10 M
For units with SW v
defined i
Band.
*ATPC
(*AirInterface 13)
ATPC parameters
*AtpcOption
(*ATPC 1)
Applicable to all units.
Enabling/disabling the
ATPC Algorithm
In
disa
teger
ble (1)
enable (2)
na (255)
BreezeACCESS 4900 System Manual
184