User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
breezeAccessVLMib
MIB Parameter Description Value/Range
*DFSSuWaitingOption
(*DFSParameters 5)
ey
enable (2)
na (255)
Applicable to AU/BU.
Defines whether the
associated SUs may should
wait for this AU/BU after it
stopped transmitting due to
radar detection, before th
starts scanning for other
AUs/BUs.
Integer
disable (1)
*DFSClearRadarChannels
(*DFSParameters 6)
rate
Integer
cancel (1)
clearRadarChannels (2)
na (255)
Applicable to AU/BU.
Clear Radar Detected and
Adjacent to Radar channels
after unit reset.
Returns the unit to ope
in default frequency
*DFSRadarDetectionChannelsTabl
e
(*DFSParameters 7)
n
r
Applicable to AU/BU.
Applicable only when DFS
option is on. Displays the
current channels defined i
the sub-band and their rada
detection status.
*DFSRadarDetectionChannelsEntr
rDetectionChannelsTa
.
ble.
y
(*DFSRada
ble 1)
Applicable to AU/BU
An entry in the DFS Radar
Detection Channels Ta
*DFSChannelIdx
nChannelsEnt
Integer
(*DFSRadarDetectio
ry 1)
Applicable to AU/BU. Read-
only. The index of the entry
in the DFS Radar Detection
Channels Table.
*DFSChannelFrequency
(*DFSRadarDetectionChannelsEnt
d lower
C
and higher replaced by *
-only. The
frequency in MHz of a
ar
Integer
ry 2)
Applicable to AU/BU with
HW revision B an
(for units with HW revision
DFSChannelFrequency
New to support a resolution
of 0.5 MHz). Read
channel in the DFS Rad
Detection Channels Table.
*DFSChannelRadarStatus
(*DFSRadarDetectionChannelsEnt
ry 3)
nels
r (2)
cted (3)
Applicable to AU/BU.
The radar detection status
of a channel in the DFS
Radar Detection Chan
Table.
Integer
radarFree (1)
adjacentToRada
radarDete
*DFSChannelFrequencyNew
(*DFSRadarDetectionChannelsEnt
r
0.5
ry 4)
Applicable to AU/BU. Read-
only. The frequency of a
channel in the DFS Rada
Detection Channels Table.
(Replaces
*DFSChannelFrequency to
support a resolution of
MHz for units with HW
revision C and higher).
DisplayString
*DFSMinimumPulsesToDetect
(*DFSParameters 8)
detect
radar.
1 - 100
Applicable to AU/BU.
Defines the minimum
number of pulses to
Integer
*DFSChannelReuseParameters
(*DFSParameters 9)
Channel Reuse Parameters
BreezeACCESS 4900 System Manual
183