User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
Appendix E - Supported MIBS and Traps
MIB Parameter Description Value/Range
*AUDefinedFrequency
(*FrequencyDefinition 8)
Applicable to AU/BU with
and higher replaced by
requ
ion
et.
products with
below 2.0 the
740 to 5830 MHz
0M Hz resolution.
version
2.0 and up the range is as
defined in the selected Sub-
Band.
HW revision B and lower
(for units with HW revision C
*DefinedAUOperatingF
encyNew to support a
resolution of 0.5 MHz).
Read-only. For 5.8 GHz
products with SW vers
below 2.0 this is the
frequency in MHz of the
AU/BU after the next res
For units with SW version
2.0 and up this is the
frequency in MHz to use
when the DFS Option is
disabled.
Integer
For 5.8 GHz
SW version
range is 5
using a 1
For units with SW
*CurrentSUOperatingFrequen
(*FrequencyDefinition 9)
cy ead ng
products with
below 2.0 the
740 to 5830 MHz
z resolution.
Applicable to SU/RB. R
only. The current operating
frequency in MHz.
DisplayStri
For 5.8 GHz
SW version
range is 5
using a 10 MH
For units with SW version
2.0 and up the range is as
defined in the selected Sub-
Band.
*SubBandSelect
(*FrequencyDefinition 10)
Sub-Band Selection
parameters
*SelectSubBandIndex
(*SubBandSelect 1)
he
ID of the sub-band used by
Applicable to all units. T
the unit.
Integer
*DFSParameters
(*FrequencyDefinition 11)
DFS Parameters. Applicable
to AU/BU.
*DFSOption
(*DFSParameters 1)
licable if
d
nd.
Applicable to AU/BU.
Enabling/disabling the DFS
Algorithm. Not app
DFS Option is not supporte
by the current Sub-Ba
Integer
disable (1)
enable (2)
na (255)
*DFSChannelCheckTime
(*DFSParameters 3)
r
cting
radar in the previously used
Range: 1 to 3600 (seconds).
Applicable to AU/BU.
Defines the time the unit
checks the channel fo
presence of radar signals
and does not transmit after
power up or association
or after moving to a new
channel due to dete
channel.
Integer
*DFSChannelAvoidancePeriod
(*DFSParameters 4) fter
detecting radar signals in a
channel of avoiding using
the channel or adjacent
channels in accordance with
the bandwidth.
60 (minutes).
Applicable to AU/BU.
Defines the time a
Integer
Range: 1 to
BreezeACCESS 4900 System Manual
182