User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
breezeAccessVLMib
MIB Parameter Description Value/Range
*FrequencySubsetFrequ
(*FrequencySubsetEn
encyNew
try 4)
ead-
MHz
nd higher).
ng Applicable to all units. R
only. The frequency in
of an entry in the Frequency
Subset table. (Replaces
*FrequencySubsetFrequenc
y to support a resolution of
0.5 MHz for units with HW
revision C a
DisplayStri
*SetSelectedFreqsSubset
(*FrequencyDefinition 5)
pply
ed for
dFreqsSubset (1)
Applicable to all units. A
the selected subset. After
the next reset the new
subset will be us
scanning.
Integer
SetSelecte
cancel (2)
*CurrentFrequencySubsetTable . Not
t
t
(*FrequencyDefinition 6)
Applicable to all units
accessible. The Curren
Frequency Subset table tha
includes all frequencies that
are currently used for
scanning.
*CurrentFrequencySubsetEntry nits. Not
(CurrentFrequencySubsetTable 1)
Applicable to all u
accessible. An entry in the
Current Frequency Subset
table.
*CurrentFrequencySubsetTableIdx
ySubsetEntry 1)
Applicable to all units. Read-
Integer
(*CurrentFrequenc only. The index of an entry
in the Current Frequency
Subset table.
*CurrentFrequencySubset nits with
C
tFr
Integer
Frequency
(*FrequencySubsetEntry 2)
Applicable to all u
HW revision B and lower
(for units with HW revision
and higher replaced by
*CurrentFrequencySubse
equencyNew to support a
resolution of 0.5 MHz).
Read-only. The frequency in
MHz of an entry in the
Current Frequency Subset
table.
*CurrentFrequencySubset
FrequencyNew
(*FrequencySubsetEntry 3)
ead-
es
.
ng
Applicable to all units. R
only. The frequency in MHz
of an entry in the Current
Frequency Subset table.
(Replac
*CurrentFrequencySubsetFr
equency to support a
resolution of 0.5 MHz for
units with HW revision C
and higher)
DisplayStri
*CurrentAUOperatingFrequency
(*FrequencyDefinition 7)
on C
quen
operating
Integer
For 5.8 GHz products with
SW version below 2.0 the
range is 5740 to 5830 MHz
0 MHz resolution.
with SW version
2.0 and up the range is as
defined in the selected Sub-
and.
Applicable to AU/BU with
HW revision B and lower
(for units with HW revisi
and higher replaced by
*CurrentUOperatingFre
cyNew to support a
resolution of 0.5 MHz).
Read-only. The
frequency in MHz.
using a 1
For units
B
BreezeACCESS 4900 System Manual
181