User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
breezeAccessVLMib
MIB Parameter Description Value/Range
*DfsSupport
(*CountryDependentParameterEntry
only.
upported
Integer
supported (1)
n
10)
Applicable to AU/BU
Read only. The s
DFS Option. otSupported (2)
*MinimumHwRevision
(*CountryDependentParameterEntry 11) Read only. The Minimum
HW Revision needed to
I
H
H (2),
H
n
Applicable to all units.
support the Sub-Band.
nteger
wRevisionA (1),
wRevisionB
wRevisionC (3),
a (255)
*AuthenticationEncryptionSupport
(CountryDependentParameters 3)
able to all units.
Read only. The supported
I
s ted (1)
n rted (2)
Applic
Authentication Encryption
Option.
nteger
uppor
otSuppo
*DataEncryptionSupport
meters 4)
Applicable to all units.
upported
I
supported (1)
notSupported (2)
(CountryDependentPara Read only. The s
Data Encryption Option.
nteger
*AESEncryptionSupport
(CountryDependentParameters 5) nly. The supported
Integer
supported (1)
n
Applicable to all units.
Read o
AES Encryption Option. otSupported (2)
*AntennaGainChange
(*SysInfo 19)
the
Antenna Gain parameter is
I
s
n (2)
Applicable to all units.
Indicates whether
changeable or fixed.
nteger
upported (1)
otSupported
E.2.2 Unit Control Parameters
MIB Parameter Description Value/Range
*UnitControl
(breezeAccessVLMib 2)
*ResetUnit
(*UnitControl 1)
o all units. Resets the
nit and applies new parameter
values.
A
u
pplicable t Integer
cancel (1)
resetSystemNow (2)
*SetDefaults
(*UnitControl 2)
Applicable to all units. Sets unit
configuration to Defaults values
after the next reset.
completeFactory: All parameters
ters
ults
d
tory (1)
y (2)
ompleteOperator (3)
uest
revert to Factory Defaults values
partialFactory: All parameters
revert to Factory Defaults values,
except the parameters required
for maintaining wireless
connectivity.
completeOperator: All parameters
revert to Operator Defaults values
partialOperator: All parame
revert to Operator Defa
values, except the parameters
required for maintaining wireless
connectivity.
Integer
NoDefaultSettingRequeste
(0),
ccompleteFa
artialFactorp
c
partialOperator (4)
qcancelCurrentPendingRe
(5)
*UnitName
(*UnitControl 3)
Applicable to all units. The unit
name.
DisplayString (
A string of up t
SIZE(32))
o 32 printable
rs. ASCII characte
BreezeACCESS 4900 System Manual
165