User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
Chapter 4 - Operation and Administration
4.2.6.2.13.7
The y
wh
res
sam
opt
4.2.6.2.14 Lost Beacons Transmission Watchdog Threshold
as
Tra
bea
The e being 218. When the
parameter is set to 0, this feature is disabled, i.e. internal refresh will never be
or
to
e association process, including the search for the
a full
4.2.6.3
m
unauthorized access by defining a set of discrete IP addresses as well as IP
red.
cess may be permitted from the
rnet only, or from both.
lowing options:
Spectrum Analysis Information Display - Continuous
Spectrum Analysis Information Display - Continuous option is available onl
en the analysis process is active. It enables viewing the continuously updated
ults of the current analysis process. The displayed information includes the
e details available for a regular Spectrum Analysis Information Display
ion.
When it is unable to send beacon frames for a predetermined period of time, such
in the case of interferences, the AU resets itself. The Lost Beacons
nsmission Threshold parameter represents the number of consecutive lost
cons after which the unit will reset itself.
range for this parameter is 100 – 1000, its default valu
performed.
4.2.6.2.15 Disassociate (AU only)
The Disassociate feature enables disassociating all SUs associated with the AU
a selected SU. This feature is useful during configuration changes, enabling
force the SU(s) to re-initiate th
best AU (or a preferred AU) using the Best AU process, without performing
reset.
The Disassociate submenu includes two options:
Disassociate All SUs
Disassociate SU By MAC Address: to disassociate a selected SU
Network Management Parameters
The Network Management Parameters menu enables protecting the Unit fro
address ranges from which the unit can be managed using protocols such as
Telnet, FTP, TFTP, SNMP, DHCP and ICMP. This excludes management messages
generated in the unit, such as Traps or Ping Test frames, which are not filte
The direction from which management access is permitted can also be
configured, which means that management ac
wireless medium only, from the wired Ethe
The Network Management Parameters menu includes the fol
Access to Network Management
Network Management Filtering
BreezeACCESS 4900 System Manual
108