User's Manual
Table Of Contents
- BreezeACCESS 4900 System Manual
- About This Manual
- Contents
- Figures
- Tables
- Chapter 1 - System Description
- Chapter 2 - Installation
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- Working with the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters
- Air Interface Parameters
- ESSID Parameters
- Frequency Definition Parameters
- Frequency Definition Submenu in AU
- Frequency Definition Submenu in SU
- Best AU Parameters (SU)
- Scanning Mode (SU only)
- Power Control Parameters
- Antenna Gain
- Cell Distance Parameters (AU only)
- Arbitration Inter-Frame Spacing (AIFS)
- Maximum Number of Associations (AU only)
- Wireless Link Trap Threshold (AU only)
- Spectrum Analysis
- Lost Beacons Transmission Watchdog Threshold
- Disassociate (AU only)
- Network Management Parameters
- Bridge Parameters
- VLAN Support
- Ethernet Broadcast Filtering (SU only)
- Ethernet Broadcast/Multicast Limiter
- Bridge Aging Time
- Broadcast Relaying (AU only)
- Unicast Relaying (AU only)
- MAC Address Deny List (AU only)
- Add MAC Address to Deny List
- Remove MAC Address from Deny List
- Roaming Option (SU only)
- Ports Control (SU only)
- Show Bridge Parameters
- Performance Parameters
- Service Parameters
- Security Parameters
- Appendix A - Software Version Loading Using TFTP
- Appendix B - File Download and Upload Using TFTP
- Appendix C - Using the Set Factory Defaults Utility
- Appendix D - Preparing the Indoor to Outdoor SU Cable
- Appendix E - Supported MIBS and Traps
- Appendix F - Parameters Summary
- Appendix G - Using the Feature License Web Application
- Appendix H - Troubleshooting
Chapter 4 - Operation and Administration
The minimum value for the Transmit Power Parameters is -10 dBm. (The ATPC
actual transmit power of the SU to lower values). The maximum
ower Parameter depends on several unit properties and
as defined for the applicable Sub-Band, together with the
a Gain. The Maximum EIRP of AUs (defined as Point-to-
lti-Point equipment) cannot exceed a certain value. In these cases the
to view the Sub-Bands supported by the unit and the
alues and options, refer to section 4.2.2.4
may reduce the
value of the Transmit P
parameters:
The modulation level
The Maximum Allowed Tx Power as defined for the applicable Sub-Band.
The Maximum EIRP
value of the Antenn
Mu
Transmit Power cannot exceed the value of (Maximum EIRP – Antenna Gain).
Maximum Tx Power parameter (in SU only)
For information on how
supported parameters’ v
.
ter is selected.
4 2.6.2.7.2 er (SU only)
aximum Tx Power parameter limits the maximum transmit power that can
or the Maximum Tx Power is -10 dBm. The maximum value
ted parameters’ values and options, refer to section 4.2.2.4
The unit calculates the maximum allowed Transmit Power according to the unit
properties and parameters listed above, and displays the allowed range when a
Transmit Power parame
The default Transmit Power is the highest allowed value.
. Maximum Tx Pow
The M
be reached by the ATPC algorithm. It also sets the upper limits for the Transmit
Power parameters.
The minimum value f
depends on several unit properties and parameters:
The modulation level
The Maximum Allowed Tx Power as defined for the applicable Sub-Band.
For information on how to view the Sub-Bands supported by the unit and the
suppor
.
ter is selected.
The unit calculates the maximum allowed Maximum Tx Power according to the
unit properties and parameters listed above, and displays the allowed range when
the Maximum Tx Power parame
The default Maximum Tx Power is the highest allowed value.
BreezeACCESS 4900 System Manual
100