Installation Guide

ManualsBrandsAltronix ManualsAutomation & SecurityPoE Driven Multi-output Power Supply/Charger, BC400 Enclosure

Rev. TANGO8P-083019

PoE Driven Multi-Output Power

Supply with Lithium Battery Backup

Installation Guide

Tango8P

- 12VDC and/or 24VDC selectable by output @ 75W max.

- Eight (8) fuse protected outputs

- Built-in Lithium Iron Phosphate Battery Charger

Tango8PCB

- 12VDC and/or 24VDC selectable by output @ 75W max.

- Eight (8) Class 2 power-limited PTC protected outputs

- Built-in Lithium Iron Phosphate Battery Charger

More than just power.

Summary of content (8 pages)

PAGE 1
PoE Driven Multi-Output Power Supply with Lithium Battery Backup Installation Guide Tango8P - 12VDC and/or 24VDC selectable by output @ 75W max. - Eight (8) fuse protected outputs - Built-in Lithium Iron Phosphate Battery Charger Tango8PCB - 12VDC and/or 24VDC selectable by output @ 75W max. - Eight (8) Class 2 power-limited PTC protected outputs - Built-in Lithium Iron Phosphate Battery Charger Rev. TANGO8P-083019 More than just power.
PAGE 2
Table of Contents: Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
Overview: Altronix Tango8P(CB) PoE Driven Multi-Output Power Supply converts an IEEE802.3bt PoE input into eight (8) regulated 24VDC and/or 12VDC outputs up to 75W. It eliminates the need for a high voltage inside the enclosure. Tango8P(CB) is designed to support a single 12V LiFePO4 (Lithium Iron Phosphate) battery for 12VDC and 24VDC backup. Specifications: Ethernet Input: • 802.3bt PoE up to 90W or 802.3at up to 30W or 802.3af up to 15W. Power Output (when using 802.3bt 90W): • 12VDC up to 6.
PAGE 4
Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, the Canadian Electrical Code and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding.
PAGE 5
LED Diagnostics: Tango1B LED Input Battery PoE Supervision Class Class 1 Class 2 Class 3 Class 4 ON Input voltage is present. Normal operating condition. Indicates Class. PoE Fail or BAT Fail. Green – – Off Off Red – – Off On Blue – – Off Off BLINKING Input voltage not present. Battery is low or missing. Refer to table below Classes 3-8 NC dry contact 30V 1A (not an LED) Class Class 5 Class 6 Class 7 Class 8 Green On On On On Red Off Off On On Blue On On On On PDS8: LED ON Green 12VDC Output.
PAGE 6
Fig.
PAGE 7
Notes: Tango8P(CB) - PoE Driven Multi-Output Power Supply -7-
PAGE 8
Enclosure Dimensions (BC400): 15.5” x 12.25” x 4.5” (394mm x 311mm x 114mm) 1.5” (38.1mm) 4.615” (117.22mm) 4.615” (117.22mm) 1.5” (38.1mm) 1.75” (44.45mm) 1.375” (34.925mm) 1.125” (28.575mm) 1.25” (31.75mm) 4.5” (114.3mm) 12.23” (310.64mm) 1.1” (27.94mm) 0.91” (23.114mm) 1.5” (38.1mm) 4.5” (114.3mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.91” (23.114mm) 2.0” (50.8mm) 1.5” (38.1mm) 15.5” (393.7mm) 2.0” (50.8mm) 5.0” (127.0mm) 5.0” (127.0mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.79” (20.