Installation Guide

ManualsBrandsAltronix ManualsAutomation & SecurityPoE Driven Multi-Output Power Supply/Charger With Access Power Controller, BC400 Enclosure

Rev. TANGO8AP-083019

PoE Driven Multi-Output

Power Supply/Charger

With Access Power Controller

Models Include:

Tango8AP

- 12VDC and/or 24VDC selectable by output @ 65W max.

- Eight (8) selectable Fail Safe, Fail-Secure fused outputs or Form “C” dry outputs

- Fire Alarm Disconnect selectable by output

- Eight (8) additional fused outputs

- Built-in Lithium Iron Phosphate Battery Charger

Tango8APCB

- 12VDC and/or 24VDC selectable by output @ 65W max.

- Eight (8) selectable Fail Safe, Fail-Secure PTC outputs or Form “C” dry outputs

- Fire Alarm Disconnect selectable by output

- Eight (8) additional PTC outputs

- Built-in Lithium Iron Phosphate Battery Charger

Installation Guide

More than just power.

Summary of content (12 pages)

PAGE 1
PoE Driven Multi-Output Power Supply/Charger With Access Power Controller Models Include: Tango8AP - 12VDC and/or 24VDC selectable by output @ 65W max. Eight (8) selectable Fail Safe, Fail-Secure fused outputs or Form “C” dry outputs Fire Alarm Disconnect selectable by output Eight (8) additional fused outputs Built-in Lithium Iron Phosphate Battery Charger Tango8APCB - 12VDC and/or 24VDC selectable by output @ 65W max.
PAGE 2
Table of Contents: Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
Overview: Altronix Tango8AP(CB) PoE Driven Multi-Output Power Supply/Charger With Access Power Controller converts an IEEE802.3bt PoE input into eight (8) regulated 24VDC and/or 12VDC outputs and eight (8) protected 24VDC and/or 12VDC outputs up to 65W. It eliminates the need for a high voltage inside of an enclosure. Tango8AP(CB) is designed to support a single 12VDC LiFePO4 (Lithium Iron Phosphate) battery for 12VDC and 24VDC backup. Specifications: Inputs: Tango1B: • 802.3bt PoE up to 90W or 802.
PAGE 4
Battery (Tango1B): • 12VDC battery charger for Lithium Iron Phosphate Battery (LiFeP04 only). • Unique technology allows for single battery to backup 12VDC and/or 24VDC systems. • Low power shutdown. Shuts down DC output terminals if battery voltage drops below 80% of nominal. Prevents deep battery discharge. Supervision (Tango1B): • Loss of PoE Input. • Battery Supervision.
PAGE 5
Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, the Canadian Electrical Code and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding.
PAGE 6
ON ON 4. Output options: ACMS8(CB) will provide up to eight (8) switched power outputs or eight (8) dry form “C” outputs, or any combination of both switched power and form “C” outputs, plus eight (8) unswitched auxiliary power outputs. Switched Power outputs: Connect the negative (–) input of the device being powered to the terminal marked [COM]. • For Fail-Safe operation connect the positive (+) input of the device being powered to the terminal marked [NC].
PAGE 7
Fig.
PAGE 8
Tango1B Terminal/RJ45 Legend PoE+ Data Input Data Output C FAIL NC + 12V – + 24V – + BAT – 8-Pin Connector (Fig. 2g, pg. 4) Function/Description IEEE802.3bt Input (Fig. 2b, pg. 4). Passes Data to Switch (Fig. 2a, pg. 4) Power and Battery Fail (Fig. 2c, pg. 4). 12VDC output (Fig. 2d, pg. 4). 24VDC output (Fig. 2e, pg. 4). Lithium Iron Phosphate battery backup (Fig. 2f, pg. 4). Facilitates electrical connection to PDS8(CB).
PAGE 9
Fig.
PAGE 10
Typical Application Diagram for ACMS8(CB): Fig. 8 Normally Open (N.O.) Door Releasing Device Access Control Panel C NO FACP NC (Fire Alarm Control Panel) +INP1-- PWR1+ +INP2-- +INP3-- +INP4-- +INP5-- +INP6-- +INP7-- +INP8-- ON C EOL JMP NC OUT8 OUT7 OUT6 FACP 3 COM-- 3 3 3 PWR1<--> PWR2 FACP EN <--> DIS 3 PWR1<--> PWR2 PWR1<--> PWR2 3 PWR1<--> PWR2 3 Altronix Corp.
PAGE 11
ACMS8(CB) Hook-Up Diagrams: Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm conditiion). Non-Latching. Fig. 10 - FACP Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm condition). Latching. RST EOL +F +R GND GND -F -R + -- EOL NC NC FACP Fig. 11 - FACP Normally Closed trigger input (Non-Latching). Fig. 12 - Normally Closed trigger input (Latching). RST EOL +F +R GND GND -F -R FACP 10K EOL 10K EOL N.O.
PAGE 12
Enclosure Dimensions (BC400): 15.5” x 12.25” x 4.5” (394mm x 311mm x 114mm) 1.5” (38.1mm) 4.615” (117.22mm) 4.615” (117.22mm) 1.5” (38.1mm) 1.75” (44.45mm) 1.375” (34.925mm) 1.125” (28.575mm) 1.25” (31.75mm) 4.5” (114.3mm) 12.23” (310.64mm) 1.1” (27.94mm) 0.91” (23.114mm) 1.5” (38.1mm) 4.5” (114.3mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.91” (23.114mm) 2.0” (50.8mm) 1.5” (38.1mm) 15.5” (393.7mm) 2.0” (50.8mm) 5.0” (127.0mm) 5.0” (127.0mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.79” (20.