Installation Guide

ManualsBrandsAltronix ManualsAutomation & SecurityAccess Power Controller with PoE Driven Power Supply/Charger, BC400 Enclosure

Rev. TANGO8A-083019

Access Power Controller with

PoE Driven Power Supply

Installation Guide

Tango8A

- 12VDC and/or 24VDC selectable by output @ 65W max.

- Eight (8) fuse protected outputs

- Eight (8) selectable Fail Safe, Fail-Secure or Form “C” dry outputs

- Fire Alarm Disconnect selectable by output

- Built-in Lithium Iron Phosphate Battery Charger

Tango8ACB

- 12VDC and/or 24VDC selectable by output @ 65W max.

- Eight (8) Class 2 power-limited PTC protected outputs

- Eight (8) selectable Fail Safe, Fail-Secure or Form “C” dry outputs

- Fire Alarm Disconnect selectable by output

- Built-in Lithium Iron Phosphate Battery Charger

More than just power.

Summary of content (12 pages)

PAGE 1
Access Power Controller with PoE Driven Power Supply Installation Guide Tango8A - 12VDC and/or 24VDC selectable by output @ 65W max. Eight (8) fuse protected outputs Eight (8) selectable Fail Safe, Fail-Secure or Form “C” dry outputs Fire Alarm Disconnect selectable by output Built-in Lithium Iron Phosphate Battery Charger Tango8ACB - 12VDC and/or 24VDC selectable by output @ 65W max.
PAGE 2
Overview: Altronix Tango8A(CB) PoE Driven Power Supply with Access Power Controller converts an IEEE802.3bt PoE input into eight (8) regulated 24VDC and/or 12VDC outputs up to 65W. It eliminates the need for a high voltage inside of an enclosure. Tango8A(CB) is designed to support a single 12VDC LiFePO4 (Lithium Iron Phosphate) battery for 12VDC and 24VDC backup. Specifications: Inputs: Tango1B: • 802.3bt PoE up to 90W or 802.3at up to 30W or 802.3af up to 15W.
PAGE 3
Stand-by Specifications: Battery 4AH 7AH 12AH Access Control Applications Stand-by 30 Mins. 45 Mins. 1.
PAGE 4
Installation Instructions: ON Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, the Canadian Electrical Code and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding.
PAGE 5
ON 9. Fire Alarm Interface options: Fig. 3 A normally closed [NC], normally open [NO] input or polarity reversal input from FACP FACP signaling circuit will trigger selected outputs. To enable FACP Disconnect for EN <--> DIS an output turn the corresponding DIP switch [SW1-SW8] ON. 1 To disable FACP disconnect for an output turn the corresponding DIP switch 2 3 [SW1-SW8] OFF. Switch is located directly to the left of the 4 Fire Alarm Interface Terminals.
PAGE 6
LED Diagnostics: Tango1B LED Input Battery PoE Supervision ON Input voltage is present. Normal operating condition. Indicates Class. PoE Fail or BAT Fail. Class Class 1 Class 2 Class 3 Class 4 Green – – Off Off Red – – Off On Blue – – Off Off BLINKING Input voltage not present. Battery is low or missing.
PAGE 7
Fig.
PAGE 8
Typical Application Diagram: Fig. 6 Normally Open (N.O.) Door Releasing Device Access Control Panel C NO FACP NC (Fire Alarm Control Panel) +INP1-- PWR1+ +INP2-- +INP3-- +INP4-- +INP5-- +INP6-- +INP7-- +INP8-- ON C EOL JMP NC OUT8 OUT7 OUT6 FACP 3 COM-- 3 3 3 PWR1<--> PWR2 FACP EN <--> DIS 3 PWR1<--> PWR2 PWR1<--> PWR2 3 PWR1<--> PWR2 3 Altronix Corp.
PAGE 9
Hook-Up Diagrams: Fig. 7 - Daisy-chaining one or more ACMS8(CB) units. EOL Jumper [EOL JMP] should be installed in the EOL position. Non-Latching. EOL JMP Jumper NC NC C Jumper C EOL JMP RST EOL +F +R GND GND -F -R FACP RST EOL +F +R GND GND -F -R FACP FACP FACP Fig. 8 - Daisy-chaining one or more ACMS8(CB) units. EOL Jumper [EOL JMP] should be installed in the EOL position. Latching Single Reset. EOL JMP Jumper NC NC C N.O.
PAGE 10
Hook-Up Diagrams: Fig. 10 - Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm conditiion). Non-Latching. Fig. 11 - FACP Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm condition). Latching. RST EOL +F +R GND GND -F -R + NC NC FACP Fig. 12 - FACP Normally Closed trigger input (Non-Latching). Fig. 13 - Normally Closed trigger input (Latching).
PAGE 11
Notes: - 11 - Tango8A(CB) - PoE Driven Access Controller
PAGE 12
Enclosure Dimensions (BC400): 15.5” x 12.25” x 4.5” (394mm x 311mm x 114mm) 1.5” (38.1mm) 4.615” (117.22mm) 4.615” (117.22mm) 1.5” (38.1mm) 1.75” (44.45mm) 1.375” (34.925mm) 1.125” (28.575mm) 1.25” (31.75mm) 4.5” (114.3mm) 12.23” (310.64mm) 1.1” (27.94mm) 0.91” (23.114mm) 1.5” (38.1mm) 4.5” (114.3mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.91” (23.114mm) 2.0” (50.8mm) 1.5” (38.1mm) 15.5” (393.7mm) 2.0” (50.8mm) 5.0” (127.0mm) 5.0” (127.0mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.79” (20.