Installation Guide

ManualsBrandsAltronix ManualsAutomation & SecurityAccess and Power Integration Kit - Includes Trove3 with TSH3, EFLOW104NB, EFLOW102NB, 2- ACM8 and PD8UL Boards and RSB2 Installed

T2SK7F8

8 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with TSH2 Altronix/Software House backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) ACM8 - Fused Access Power Controller

- One (1) VR6 - Voltage Regulator

- One (1) PDS8 - Dual Input Power Distribution Module

- One (1) Rocker Switch Bracket with One (1) Rocker Switch

T3SK75F8

8 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove3 enclosure with TSH3 Altronix/Software House backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) eFlow102NB - Power Supply/Charger

- One (1) ACM8 - Fused Access Power Controller

- One (1) PD8UL - Fused Power Distribution Module

- One (1) Rocker Switch Bracket with Two (2) Rocker Switches

T3SK75F16

16 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove3 enclosure with TSH3 Altronix/Software House backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) eFlow102NB - Power Supply/Charger

- Two (2) ACM8 - Fused Access Power Controllers

- One (1) PD8UL - Fused Power Distribution Module

- One (1) Rocker Switch Bracket with Two (2) Rocker Switches

Access & Power Integration

Rev. TSK110817

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners. More than just power.™

Installation Guide

Summary of content (8 pages)

PAGE 1
Access & Power Integration T2SK7F8 8 Door Kit with Fused Outputs Fully assembled kit includes: - Trove2 enclosure with TSH2 Altronix/Software House backplane One (1) eFlow104NB - Power Supply/Charger One (1) ACM8 - Fused Access Power Controller One (1) VR6 - Voltage Regulator One (1) PDS8 - Dual Input Power Distribution Module One (1) Rocker Switch Bracket with One (1) Rocker Switch T3SK75F8 8 Door Kit with Fused Outputs Fully assembled kit includes: - Trove3 enclosure with TSH3 Altronix/Software House
PAGE 2
Overview: Altronix Trove Software House kits are pre-assembled and consist of Trove enclosure with factory installed Altronix power supply/chargers and sub-assemblies. These kits also accommodate various combinations of Software House boards for up to sixteen (16) doors in a single enclosure. Configuration Chart: – – – 20.1926.4 – – • • • • • 20.1926.4 – – – 10.0313.2 24VDC @ 9.2A 8 8.0 2.5 – – 10.0313.2 (eFlow104NB) 5A/250V 15A/ 10A/ 2.5A/ 32V 250V 250V – – 15A/ 10A/ 2.
PAGE 3
T2SK7F8: Configuration of Software House iSTAR Ultra Boards 1. 2. Align the Software House boards on the backplane to match the boards’ mounting holes with corresponding pems. Fasten standoffs (provided) to pems that match the hole pattern for Software House iSTAR Ultra GCM, iSTAR Ultra ACM, and /or I8, R8, I8-CSI boards (Fig. 2, 2a, pg. 3). 3. Mount Software House boards to standoffs utilizing provided 5/16” pan head screws (Fig. 2a, pg. 3).
PAGE 4
T2SK7F8: Configuration of Software House iSTAR Pro Boards 1. 2. Align the Software House boards on the backplane to match the boards’ mounting holes with corresponding pems. Fasten provided standoffs to pems that match the hole pattern for Software House iSTAR Pro GCM, iSTAR ACM SE/PRO ACM, and /or I8, R8, I8-CSI boards (Fig. 3, 3a, pg. 4). 3. Mount Software House boards to standoffs utilizing provided 5/16” pan head screws (Fig. 3a, pg. 4).
PAGE 5
T3SK75F8 or T3SK75F16: Configuration of Software House iSTAR Ultra Boards 1. 2. Align the Software House boards on the backplane to match the boards’ mounting holes with pems provided. Fasten standoffs (provided) to pems that match the hole pattern for Software House iSTAR Ultra GCM, iSTAR Ultra ACM, and /or I8, R8, I8-CSI boards (Fig. 4, 4a, pg. 5). 3. Mount Software House boards to standoffs utilizing provided 5/16” pan head screws (Fig. 4a, pg. 5).
PAGE 6
T3SK75F8 or T3SK75F16: Configuration of Software House iSTAR Pro Boards 1. 2. Align the Software House boards on the backplane to match the boards’ mounting holes with pems provided. Fasten provided standoffs to pems that match the hole pattern for Software House iSTAR Pro GCM, iSTAR ACM SE/PRO ACM, and /or I8, R8, I8-CSI boards (Fig. 5, 5a, pg. 6). 3. Mount Software House boards to standoffs utilizing provided 5/16” pan head screws (Fig. 5a, pg. 6).
PAGE 7
T2SK7F8 Enclosure Dimensions (H x W x D approximate): 27.25” x 21.5” x 6.5” (692.2mm x 552.5mm x 165.1mm) 21.50” (546.1mm) 2.00” (50.8mm) 5.25” (133.35mm) 3.50” (88.9mm) 3.50” (88.9mm) 5.25” (133.35mm) 0.685” (17.399mm) 1.25” (31.75mm) 0.5625” (14.29mm) 1.77” (44.96mm) 2.415” (61.34mm) Knockouts 1.125” (28.32mm) 0.885” (22.479mm) 6.25” (158.75mm) 0.85” (21.59mm) 6.25” (158.75mm) 1.25” (31.75mm) 19.80” (502.92mm) 1.5” (38.1mm) 2.00” (50.8mm) 6.75” (171.45mm) G 8.25” (209.54mm) 27.00” (685.
PAGE 8
T3SK75F8 and T3SK75F16 Enclosure Dimensions (H x W x D approximate): 36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm) 2.00” (50.8mm) 7.12” (222.25mm) 9.5” (241.3mm) 1.25” (31.75mm) 1.55” (39.37mm) 30.12” (768.1mm) 14.01” (355.9mm) 2.00” (50.8mm) 14.01” (355.9mm) 1.10” (27.9mm) 2.00” (50.8mm) 10.75” (273.1mm) 1.78” (45.21mm) 1.07” (27.2mm) 1.25” (31.8mm) 9.5” (241.3mm) 10.75” (273.1mm) G G 10.62” (269.8mm) 10.62” (269.8mm) 33.63” (854.20mm) 10.75” (273.1mm) 36.12” (917.5mm) 10.