Installation Guide

ManualsBrandsAltronix ManualsAutomation & Security12-Door Access and Power Integration Kit Includes Trove2KH2 with eFlow6NB, T1618300K, ACM4, ACM8

T2KHK3F12

12 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with TKH2 Altronix/Kantech backplane

- One (1) eFlow6NB - Power Supply/Charger

- One (1) T1618300K - Transformer

- One (1) ACM4 - Fused Access Power Controller

- One (1) ACM8 - Fused Access Power Controller

Access & Power Integration

Rev. 040819

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners. More than just power.™

Installation Guide

All components of this Trove kit are UL Listed sub-assemblies.

Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

Summary of content (4 pages)

PAGE 1
Access & Power Integration T2KHK3F12 12 Door Kit with Fused Outputs Fully assembled kit includes: - Trove2 enclosure with TKH2 Altronix/Kantech backplane One (1) eFlow6NB - Power Supply/Charger One (1) T1618300K - Transformer One (1) ACM4 - Fused Access Power Controller One (1) ACM8 - Fused Access Power Controller All components of this Trove kit are UL Listed sub-assemblies. Please refer to the included corresponding Sub-Assembly Installation Guides for further information.
PAGE 2
Overview: Altronix T2KHK3F12 Trove Kantech kit is pre-assembled and consists of Trove2KH2 enclosure/backplane with factory installed Altronix power supply/charger and sub-assemblies. T2KHK3F12 kit also accommodates various combinations of Kantech boards for up to twelve (12) doors in a single enclosure. TKH2 accommodates a combination of the following Kantech boards: • • • Up to four (4) KT-MOD-INP16 or KT-MOD-OUTP16. Up to four (4) KT300. Up to three (3) KT400. 20.28-26.
PAGE 3
Configuration of Kantech Boards: 1. Align Kantech boards on the backplane to match the boards’ mounting holes with corresponding holes in backplane. a. Position spacer over appropriate hole on the rear of backplane and depress it until it locks in place (Fig. 2a, pg. 3, Step 1a). b. Depress down on board to secure it to the spacer (Fig. 2a, pg. 3, Step 1b). 2. Fasten backplane to Trove2 enclosure utilizing pan head screws (provided).
PAGE 4
Enclosure Dimensions (H x W x D): 27.25” x 21.75” x 6.5” (692.2mm x 552.5mm x 165.1mm) 21.50” (546.1mm) 5.25” (133.35mm) 3.5”(88.9mm) 3.5”(88.9mm) 5.25” (133.35mm) 0.685” (17.4mm) 1.25” (31.8mm) 6.25” (158.8mm) 1.25” (31.8mm) 0.5625” (14.3mm) 1.77” (45mm) 2.415” (61.3mm) 1.5” (38.1mm) Knockouts 1.125” (28.3mm) 0.885” (22.5mm) 2.00” (50.8mm) 6.25” (158.8mm) 2.00” (50.8mm) 19.80” (502.9mm) 8.00” (203.2mm) 27” (685.8mm) 8.25” (209.5mm) 6.75” (171.5mm) 2.00” (50.8mm) 0.85” (21.6mm) 2.00” (50.