Installation Guide

ManualsBrandsAltronix ManualsAutomation & Security4-Door Access and Power Integration Kit Includes Trove1V1R with eFlow6NB, ACM4, PDS8, VR6

Rev. T1RV3F4111918

T1RV3F4

Fully assembled kit includes:

- Trove1R rack enclosure with Altronix/HID VertX® backplane (TV1R)

- (1) eFlow6NB - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) PDS8 - Fused Dual Output Power Distribution Module

- (1) ACM4 - Fused Access Power Controller

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Access & Power Integration

Summary of content (8 pages)

PAGE 1
Access & Power Integration T1RV3F4 Fully assembled kit includes: - Trove1R rack enclosure with Altronix/HID VertX® backplane (TV1R) - (1) eFlow6NB - Power Supply/Charger - (1) VR6 - Voltage Regulator - (1) PDS8 - Fused Dual Output Power Distribution Module - (1) ACM4 - Fused Access Power Controller Installation Guide All registered trademarks are property of their respective owners. More than just power.™ Rev. T1RV3F4111918 Installing Company: ______________________ Service Rep.
PAGE 2
Overview: Altronix T1RV3F4 rack kit is pre-assembled and consist of Trove1V1R enclosure/backplane with factory installed Altronix power supply/ charger and sub-assemblies. This kit also accommodates various combinations of HID VertX® boards for up to six (6) doors in a single enclosure. Fail-Safe/Fail-Secure or Dry Form “C” Outputs 10A/ 32V 3A/ 32V 4 PDS8 Board Output Fuse Rating ACM4 Board Output Fuse Rating 2.
PAGE 3
Assembling and Attaching Z Bracket Wire Management Accessory (included): Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory. 1. Carefully unpack Z Bracket. Do not discard hardware (included) (Fig. 1, pg. 3). 2. Attach arms to each other using bolts and lock nuts (Fig. 1a, pg. 3). 3. Attach the hinge brackets to the ends of arms using bolts and nuts positioning them as shown on Fig. 1b, pg. 3. 4. Make sure that all nuts are tightened.
PAGE 4
Installation Instructions for T1RV3F4: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Remove backplane from enclosure prior to installing into rack cabinet (do not discard hardware). 2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) turn the enclosure upside down.
PAGE 5
T1RV3F4: Configuration of HID VertX® Boards: 1. Fasten spacers onto metal pems configuration (A) of backplane depending on the access controller (Fig. 4, pg. 5). 2. Position access controller module over corresponding spacers and fasten screws into spacers (Fig. 4a, pg. 5). 3. Mount backplane to enclosure with hardware. Access Controller Position Chart for the Following Models: HID VertX® Sub-Assembly V100 V200 V300 V1000 V2000 Pem Mounting A Fig. 4 Fig.
PAGE 6
Notes: - 6 - T1RV3F4
PAGE 7
Notes: T1RV3F4 - 7 -
PAGE 8
Trove1R Enclosure Dimensions (H x W x D): 3.25” x 19.0” x 26.5” (82.6mm x 482.6mm x 673.1mm). Shown with Z Bracket attached. 0.1” 2.5mm 1.5” 38.1mm 11.175” (283.8mm) 1” (25.4mm) 2.4” 61mm 0.55” (14mm) 3.62” 92mm R 1.27” (32.3mm) 4.57” 116.1mm 26.5” 673.1mm 19” (482.6mm) 3.25” 82.3mm Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 web site: www.altronix.com | e-mail: info@altronix.com | Made in U.S.A.