Installation Guide

ManualsBrandsAltronix ManualsAutomation & SecurityAccess and Power Integration Kit

Rev. T1RAL13F8P8032019

T1RAL13F8P8

Fully assembled kit includes:

- Trove1R rack enclosure with Altronix backplane (TAL1R)

- (1) eFlow4NB - Power Supply/Charger

- (1) eFlow6NB - Power Supply/Charger

- (1) ACM8 - Fused Access Power Controller

- (1) PD8UL - Fused Power Distribution Module

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Access & Power Integration

Summary of content (8 pages)

PAGE 1
Access & Power Integration T1RAL13F8P8 Fully assembled kit includes: - Trove1R rack enclosure with Altronix backplane (TAL1R) - (1) eFlow4NB - Power Supply/Charger - (1) eFlow6NB - Power Supply/Charger - (1) ACM8 - Fused Access Power Controller - (1) PD8UL - Fused Power Distribution Module Installation Guide All registered trademarks are property of their respective owners. More than just power.™ Rev. T1RAL13F8P8032019 Installing Company: ______________________ Service Rep.
PAGE 2
Overview: Altronix T1RAL13F8P8 Trove Rack kit is pre-assembled and consist of Trove1AL1R enclosure/backplane with factory installed Altronix power supply/chargers and sub-assemblies. 5A/ 250V PD8UL Board Output Fuse Rating 7 PD8UL Board Input Fuse Rating T1RAL13F8P8 Maximum Supply Current for Main Power [DC] [Aux] and Aux.
PAGE 3
Assembling and Attaching Z Bracket Wire Management Accessory (included): Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory. 1. Carefully unpack Z Bracket. Do not discard hardware (included) (Fig. 1, pg. 3). 2. Attach arms to each other using bolts and lock nuts (Fig. 1a, pg. 3). 3. Attach the hinge brackets to the ends of arms using bolts and nuts positioning them as shown on Fig. 1b, pg. 3. 4. Make sure that all nuts are tightened.
PAGE 4
Installation Instructions for T1RAL13F8P8: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Remove backplane from enclosure prior to installing into rack cabinet (do not discard hardware). 2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) turn the enclosure upside down.
PAGE 5
2 3 OUTPUT 4 C NO AC FAIL NC C NO BAT FAIL OUTPUT 3 NC AC DC 1 min enable 2 hr. disable OUTPUT 2 AC1 TRIGGER EOL SUPERVISED NO GND RESET OUTPUT 1 OUTPUT 5 OUTPUT 7 OUTPUT 6 N G L OUTPUT 8 NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM 4 1 ON 2 3 4 10A 250V +INP- T + RETINTERFACE MAIN NO C NC FACP + + Power Control 1 + AUX --- ON NO GND RESET F8 TRIGGER EOL SUPERVISED F7 N P 1 min enable 2 hr.
PAGE 6
Notes: - 6 - T1RAL13F8P8
PAGE 7
TAL1R Dimensions: 18.5” x 15.25” x 0.3125” (469.9mm x 387.4mm x 7.9mm) 15.25” (387.4mm) 18.5” 469.
PAGE 8
Trove1R Enclosure Dimensions (H x W x D): 3.25” x 19.0” x 26.5” (82.6mm x 482.6mm x 673.1mm). Shown with Z Bracket attached. 0.1” 2.5mm 1.5” 38.1mm 11.175” (283.8mm) 1” (25.4mm) 2.4” 61mm 0.55” (14mm) 3.62” 92mm R 1.27” (32.3mm) 4.57” 116.1mm 26.5” 673.1mm 19” (482.6mm) 3.25” 82.3mm Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 web site: www.altronix.com | e-mail: info@altronix.com | Made in U.S.A.