Installation Guide

ManualsBrandsAltronix ManualsAutomation & SecurityAccess and Power Integration Kit

Rev. T1RAG3F8_110419

T1RAG3F8

Fully assembled kit includes:

- Trove1R rack enclosure with T1AG1R Altronix/AMAG backplane

- (1) eFlow6NB - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) PDS8 - Fused Dual Output Power Distribution Module

- (1) ACM4 - Fused Access Power Controller

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Access & Power Integration

Summary of content (8 pages)

PAGE 1
Access & Power Integration T1RAG3F8 Fully assembled kit includes: - Trove1R rack enclosure with T1AG1R Altronix/AMAG backplane - (1) eFlow6NB - Power Supply/Charger - (1) VR6 - Voltage Regulator - (1) PDS8 - Fused Dual Output Power Distribution Module - (1) ACM4 - Fused Access Power Controller Installation Guide All registered trademarks are property of their respective owners. More than just power.™ Rev. T1RAG3F8_110419 Installing Company: ______________________ Service Rep.
PAGE 2
Overview: Altronix T1RAG3F8 Trove rack kit is pre-assembled and consist of Trove rack enclosure/backplane with factory installed Altronix power supply/charger and sub-assemblies. Kits accommodate up to two (2) AMAG M4000 modules for up to eight (8) doors in a single enclosure. Configuration Chart: Altronix Model Number Nominal DC Output Voltage [DC] [Aux] 120VAC 60Hz Input Current Power Supply Board Input Fuse Rating Power Supply Board Battery Fuse Rating Output Range (VDC) Output Range (VDC) 3.
PAGE 3
Assembling and Attaching Z Bracket Wire Management Accessory (included): Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory. 1. Carefully unpack Z Bracket. Do not discard hardware (included) (Fig. 1, pg. 3). 2. Attach arms to each other using bolts and lock nuts (Fig. 1a, pg. 3). 3. Attach the hinge brackets to the ends of arms using bolts and nuts positioning them as shown on Fig. 1b, pg. 3. 4. Make sure that all nuts are tightened.
PAGE 4
Installation Instructions for T1RAG3F8: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Remove backplane from enclosure prior to installing into rack cabinet (do not discard hardware). 2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) turn the enclosure upside down.
PAGE 5
1. 2. 3. 4. T1RAG3F8: Configuration of AMAG M4000 Modules: Align the AMAG M4000 modules on the backplane to match the boards’ mounting holes with corresponding pems. Fasten spacers (provided) onto metal pems (Fig. 4a, pg. 3). Mount AMAG M4000 modules to spacers utilizing pan head screws (provided) (Fig. 4a, pg. 3). Fasten TAG1R backplane to Trove1R rack enclosure utilizing hardware (provided). Position Chart for the Following Models: M4000 M4000-DEC4, M4000-IOC20/16 Pem Mounting A Fig. 4 Fig.
PAGE 6
Notes: - 6 - T1RAG3F8
PAGE 7
Notes: T1RAG3F8 - 7 -
PAGE 8
T1RAG3F8 Enclosure Dimensions (H x W x D): 3.25” x 19.0” x 26.5” (82.6mm x 482.6mm x 673.1mm). Shown with Z Bracket attached. 0.1” 2.5mm 1.5” 38.1mm 11.175” (283.8mm) 1” (25.4mm) 2.4” 61mm 0.55” (14mm) 3.62” 92mm R 1.27” (32.3mm) 4.57” 116.1mm 26.5” 673.1mm 19” (482.6mm) 3.25” 82.3mm Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 web site: www.altronix.com | e-mail: info@altronix.com | Made in U.S.A.