SMP7CTX220 Series Power Supply/Chargers Models Include: SMP7CTX220 SMP7PMCTX220 SMP7PMCTXX220 - Single Output. SMP7PMP4220 - Four (4) Fuse Protected Outputs. SMP7PMP8220 - Eight (8) Fuse Protected Outputs. SMP7PMP16220 - Sixteen (16) Fuse Protected Outputs. SMP7PMP4CB220 - Four (4) PTC Protected Outputs. SMP7PMP8CB220 Eight (8) PTC Protected Outputs. SMP7PMP16CB220 - Sixteen (16) PTC Protected Outputs. For a red enclosure add an “R” suffix to the part #, e.g. SMP7CTX220R Installation Guide Rev.
Overview: Altronix SMP7CTX220 Series power supply/chargers convert a 220VAC (working range 198VAC - 256VAC), 50/60Hz into a regulated 12VDC or 24VDC output with up to 6A of continuous load current (see specifications).
Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding.
Terminal Identification: Power Supply Board: Terminal Legend L, G, N – DC + Function/Description Connect 220VAC to these terminals: L to Hot, N to Neutral. 12VDC / 24VDC @ 6A continuous output. *AC FAIL NC, C, NO Used to notify loss of AC power, e.g. connect to audible device or alarm panel. Relay normally energized when AC power is present. Contact rating 1A @ 120VAC / 28VDC. *Low Battery NC, C, NO – BAT + Used to indicate low battery condition, e.g. connect to alarm panel.
Fig. 1 Fig. 1a Switch disables power mains line voltage input. If stand-by battery (batteries) are connected, the DC output remains on ON ON 220VAC power mains L Power Supply 5A 250V Ground Lug G N AC DC NC C NO LOW BAT See LED Diagnostics, pg. 3 OFF - 24V ON - 12V --- DC + LOW BAT --- BAT + NC C Power Distribution Module(s) Power Supply Board AC FAIL NC C NO Fig.
Power Distribution Module(s): Fig. 2 - PD4/PD4CB F1 Used on PTC Models F2 F3 F4 1P, 2P, 3P, 4P = FUSED OUTPUTS 1N, 2N, 3N, 4N = COMMON OUTPUTS LED 1N 1P 2P 2N 3N 3P 4P 4N INPUT COMMON POWER OUTPUTS DC Output to devices From Power Supply Board (Factory Installed) Fig. 3 - PD8/PD8CB OFF SW1 1 2 3 4 5 6 7 8 ON Used on PTC Models P D1 FUSED POWER OUTPUTS R1 N LED INPUT COMMON POWER OUTPUTS DC Output to devices From Power Supply Board (Factory Installed) Fig.
Enclosure Dimensions (BC300): SMP7CTX220, SMP7PMCTX220, SMP7PMP4220, SMP7PMP4CB220, SMP7PMP8220, SMP7PMP8CB220, SMP7PMP16220, SMP7PMP16CB220 13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm) Enclosure accommodates up to two (2) 12VDC/7AH batteries. Also available to accommodate up to two (2) 12VDC/12AH batteries (please contact Altronix). 1.40” (35.6mm) 4.85” (123.2mm) 4.85” (123.2mm) 1.40” (35.6mm) 1.20” (30.5mm) 0.75” (19.1mm) 3.25” (82.6mm) 1.20” (30.5mm) 0.75” (19.1mm) 12.5” (317.5mm) 11.
Enclosure Dimensions (BC400): SMP7PMCTXX220 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm) Enclosure accommodates up to two (2) 12VDC/12AH batteries. 1.5” (38.1mm) 4.615” (117.2mm) 4.615” (117.2mm) 1.5” (38.1mm) 1.75” (44.5mm) 1.25” (31.8mm) 4.5” (114.3mm) 4.5” (114.3mm) 12.23” (310.6mm) 1.1” (27.9mm) 1.1” (27.9mm) 1.375” (34.9mm) 1.5” (38.1mm) 1.25” (31.8mm) 1.5” (38.1mm) 0.91” (23.1mm) 0.91” (23.1mm) 1.125” (28.6mm) 15.5” (393.7mm) 2.0” (50.8mm) 2.0” (50.8mm) 5.0” (127.0mm) 0.79” (20.
