Installation Instructions Owner manual

ManualsBrandsAltronix ManualsAccessories for electricalSMP5PMP8CB

Power Supply Voltage Output Specifications: *

Output VDC Switch Position Max. Load DC

12VDC SW1 - Closed

(Fig. 1b, pg. 3) 4 amp

24VDC SW1 - Open

(Fig. 1b, pg. 3) 4 amp

*Specified at 25˚ C ambient.

Installation Instructions:

The unit should be installed in accordance with The National Electrical Code and all applicable Local Regulations.

1. Mount the unit in desired location.

2. Set SW1 on the power supply board to the desired DC output voltage

(Power Supply Voltage Output Specification Chart).

Connect

C po

wer to terminals marked [L & N], connect ground to terminal marked [G] (if used).

Use 18

WG or lar

ger for all po

er connections (Batter

y, DC output).

Use 22 AWG to 18 AWG for power limited circuits (AC Fail/Low Battery reporting).

SMP5CTX - 1 - - - - .95 / .5 4 13.5”H x 13”W x 3.25”D

SMP5PMCTX - 1 - - - x .95 / .5 4 13.5”H x 13”W x 3.25”D

SMP5PMCTXX - 1 - - - x .95 / .5 4 15.5”H x 12”W x 4.5”D

SMP5PMP4 PD4 4 x - 3.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D

SMP5PMP4CB PD4CB 4 - x 2.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D

SMP5PMP8 PD8

8 x - 3.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D

SMP5PMP8CB PD8CB 8 - x 2.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D

SMP5PMP16 PD16W 16 x - 3.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D

SMP5PMP16CB PD16WCB 16 - x 2.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D

Altronix

Model Number

Accessory Power

Distribution

Module(s)

Number of Outputs

Fused Outputs

PTC Outputs

Indi

vidual Output

Rating (amp)

115VAC/230VAC

Input Current (amp)

12/24VDC Total

Output Current (amp)

Enclosure Dimensions

SMP5CTX Series Power Supply Configuration Reference Chart:

Overview:

These units will convert a 115VAC or 230VAC, 50Hz/60Hz input, into a regulated 12VDC or 24VDC output up to 4

amps of continuous load current (see specifications).

Specifications:

• Universal 115/230VAC input.

• Maximum charge current .5 amp.

• Filtered and electronically regulated outputs.

• Built-in charger for sealed lead acid or gel type batteries.

• Automatic switch over to stand-by battery when

AC fails (zero voltage drop).

• AC input and DC output LED indicators.

• Short circuit and thermal overload protection.

• Complete with power supply, power distribution module

hen applicab

le), enclosure, cam lock & battery leads.

• Power on-off switch.

Supervised Models Only:

• AC fail supervision (form "C" contacts).

• Low battery supervision (form "C" contacts).

- 1 -

SMP5CTX Series

Supervised

Summary of content (8 pages)

PAGE 1
SMP5CTX Series Al tro M nix od el Nu m be r Ac c Di esso s r M tribu y Po od ti w ule on er (s) Nu m b Fu er o f se d O Ou ut tput PT pu s C Ou ts In div tput s Ra id tin ual g O Su (am utp p) ut pe rv 11 ised 5 In VA pu C/ t C 23 ur 0VA re C 12 nt / 2 (a Ou 4V m tp D p) u C t En C T o clo ur ta su ren l re t ( Di am m p) en sio ns SMP5CTX Series Power Supply Configuration Reference Chart: SMP5CTX - 1 - - - - .95 / .5 4 13.5”H x 13”W x 3.25”D SMP5PMCTX - 1 - - - x .95 / .5 4 13.
PAGE 2
4. Connect devices to be powered: a. For Power Supply Board connect to terminals marked [– DC + ]. b. For Power Distribution Module(s) connect devices to be powered to terminal pairs 1 to 4 marked [1P & 1N thru 4P & 4N] (Fig. 2, pg. 4) or 1 to 8 marked [1P & 1N thru 8P & 8N] (Fig. 3, pg. 4) or 1 to 16 marked [1P & 1N thru 16P & 16N] (Fig. 4, pg. 4) carefully observing correct polarity. Note: Measure output voltage before connecting devices. This helps avoid potential damage.
PAGE 3
Fig. 1 CAUTION: De-energize unit prior to servicing. For continued protection against fire hazard replace fuse with the same type and rating 5A, 250V. OFF ON 5A 250V L LOW BAT NC C NC INPUT Power Distribution Module(s) AC DC C NO NC C NC AC FAIL NC C NO AC FAIL 115/230VAC power mains N Fig. 1a Green Lead G Wire Strap (from Enclosure to Door) NO LOW BAT --- DC + OPEN - 24VDC CLOSED - 12VDC --- BAT + SW1: 24V - OPEN 12V - CLOSED Fig.
PAGE 4
Power Distribution Module(s): Fig. 2 Fig. 3 F1 F1 F3 F2 F4 1 Used on PTC Models 1 1P, 2P,3P,4P = FUSED OUTPUT S 1N, 2N, 3N, 4N = OMMON C OUTPUT S 2 3 4 5 6 7 8 P D1 LED 1P 1N C O MM O N 2P P OW E R 2N 3N 3P 4P INPUT common outputs protected outputs From Power Supply Board (Factory Installed) POWER 9 10 11 12 13 14 15 16 N P N P P S XFMR Input For continuous protection against risk of fire replace fuses with same type and rating.
PAGE 5
Enclosure Dimensions for: • SMP5PMCTX • SMP5PMP4 • SMP5PMP8 • SMP5PMP8CB • SMP5PMP4CB • SMP5PMP16 • SMP5PMP16CB 13.5”H x 13”W x 3.25”D Enclosure accommodates up to two (2) 12VDC/7AH batteries. Also available to accommodate up to two (2) 12VDC/12AH batteries (please contact Altronix). 1.40" 4.85" 4.85" 1.40" 1.20" 3.25" Top 12.50" 1.20" 0.75" 1.20" 11.00" 0.75" 0.9375" 1.40" 1.40" 5.10" 5.10" Left Right 5.10" 6.5625" 0.9375" 3.25" 3.25" Bottom 3.25" 1.00" 1.00" 1.00" 10.
PAGE 6
Enclosure Dimensions for: • SMP5PMCTXX 15.5”H x 12”W x 4.5”D Enclosure accommodates up to two (2) 12VDC/12AH batteries. 1.500" 4.615" 4.615" 1.500" 1.750" 1.375" 1.125" 4.500" 12.230" 1.250" 4.500" 1.100" 1.250" 1.100" 0.910" 0.910" 1.500" 1.500" 2.000" 15.500" 2.000" 5.000" 5.000" 0.790" 1.250" 1.100" 1.250" 1.750" 1.500" 4.615" 4.615" -6- 1.
PAGE 7
Notes: -7-
PAGE 8
Notes: Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 web site: www.altronix.com, e-mail: info@altronix.com, Made in U.S.A. IISMP5PMCTX - Rev.