SMP10C12X Series Power Supply/Charger Installation Guide Models Include: SMP10C12X SMP10C12XX SMP10PMC12X SMP10PMC12XX - Single Output. SMP10PM12P4 SMP10PM12P4CB SMP10PM12P8 SMP10PM12P8CB SMP10PM12P16 SMP10PM12P16CB - Four (4) Fuse Protected Outputs. - Eight (8) Fuse Protected Outputs. - Sixteen (16) Fuse Protected Outputs. Rev. 051105 - Four (4) PTC Protected Outputs. - Eight (8) PTC Protected Outputs. - Sixteen (16) PTC Protected Outputs. More than just power.
Overview: Altronix SMP10C12X Series power supply/chargers convert a 115VAC, 60Hz input into a regulated 12VDC output with up to 10A of continuous load current (see specifications).
4. Slide [Power ON/OFF] switch to ON position. 5. Measure output voltage before connecting devices. This helps avoiding potential damage. Keep power-limited wiring separate from non power-limited wiring (115VAC, 60Hz Input, Battery Wires). Minimum 0.25” spacing must be provided. CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment. There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel. 6.
N NC C C NO Caution: Equipment to be installed / serviced by authorized / trained personnel only. Shut branch circuit power before installing / servicing equipment. NC WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to the National Electrical Code and all local codes.
Fig.
Power Distribution Module(s): Fig. 3 - PD4/PD4CB F1 Used on PTC Models F2 F3 F4 1P, 2P, 3P, 4P = FUSED OUTPUTS 1N, 2N, 3N, 4N = COMMON OUTPUTS LED 2P 1N 1P COMMON 2N POWER 4P 3N 3P 4N INPUT OUTPUTS DC Output to devices From Power Supply Board (Factory Installed) Fig. 4 - PD8/PD8CB OFF SW1 Used on PTC Models 2 3 4 5 6 7 8 ON 1 P D1 FUSED POWER OUTPUTS R1 N LED INPUT COMMON POWER OUTPUTS DC Output to devices From Power Supply Board (Factory Installed) Fig.
Enclosure Dimensions (BC300): SMP10C12X, SMP10PMC12X, SMP10PM12P4, SMP10PM12P4CB, SMP10PM12P8, SMP10PM12P8CB, SMP10PM12P16, SMP10PM12P16CB 13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm) Enclosure accommodates up to two (2) 12VDC/7AH batteries. Also available to accommodate up to two (2) 12VDC/12AH batteries (please contact Altronix). 1.40” (36mm) 4.85” (123mm) 4.85” (123mm) 1.40” (36mm) 1.20” (31mm) 3.25” (83mm) 1.20” (31mm) 0.75” (19mm) 12.5” (318mm) 11.0” (279mm) 1.20” (31mm) 0.75” (19mm) 0.
Enclosure Dimensions (BC400): SMP10C12XX, SMP10PMC12XX 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm) Enclosure accommodates up to two (2) 12VDC/12AH batteries. 1.5” (38.1mm) 4.615” (117.22mm) 4.615” (117.22mm) 1.5” (38.1mm) 1.75” (44.45mm) 1.375” (34.925mm) 1.125” (28.575mm) 1.25” (31.75mm) 4.5” (114.3mm) 12.23” (310.64mm) 1.1” (27.94mm) 0.91” (23.114mm) 1.5” (38.1mm) 4.5” (114.3mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.91” (23.114mm) 2.0” (50.8mm) 1.5” (38.1mm) 15.5” (393.7mm) 2.0” (50.
