Installation Guide

ManualsBrandsAltronix Manualselectrical connectionSMP10C12X

SMP10C12Xseries - 1 -

Overview:

These units convert a 115VAC 50/60Hz input into a regulated 12VDC output at up to 10 amp continuous supply current

(see specifications).

SMP10C12X Series Power Supply Configuration Reference Chart:

Altronix

Model Number

Accessory

Power

Distribution

Module(s)

Number of

Outputs

Fused Outputs

PTC Outputs

Output Rating

(amp) per

Output

Supervised

115VAC

50/60Hz Input

Current (amp)

12VDC Total

Output Current

(amp)

SMP10C12X

- 1 - - 10 - 1.45 10

SMP10C12XX*

- 1 - - 10 - 1.45 10

SMP10PMC12X

- 1 - - 10 x 1.45 10

SMP10PMC12XX*

- 1 - - 10 x 1.45 10

SMP10PM12P4

PD4 4 - 3.5 x 1.45 10

SMP10PM12P4CB

PD4CB 4 - x 2.5 x 1.45 10

SMP10PM12P8

PD8 8 x - 3.5 x 1.45 10

SMP10PM12P8CB

PD8CB 8 - x 2.5 x 1.45 10

SMP10PM12P16

PD16W 16 x - 3.5 x 1.45 10

SMP10PM12P16CB

PD16WCB 16 - x 2.5 x 1.45 10

*Refer to Enclosure Dimensions on pg.7 for enclosure size.

Specifications:

Installation Instructions:

Wiring methods should be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI and with all local

codes and authorities having jurisdiction. Product is intended for indoor use only.

1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the

enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s

upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the

enclosure. Drill the lower holes and install three fasteners. Place the enclosure’s upper keyholes over the two

upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pgs. 6-7).

Secure enclosure to earth ground.

2. Connect AC power to the terminals marked [L & N].

Use 18 AWG or larger for all power connections (Battery, DC output).

3. Measure output voltage before connecting devices. This helps avoiding potential damage.

Keep power-limited wiring separate from non power-limited wiring (115VAC 50/60Hz Input, Battery Wires).

Minimum 0.25” spacing must be provided.

CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment.

There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel.

Battery Backup:

• Built-inchargerforsealedleadacidorgeltypebatteries.

• Maximumchargecurrent0.7amp.

• Filteredandelectronicallyregulatedoutputs.

• Automaticswitchovertostand-bybatterywhen

AC fails (zero voltage drop).

Features:

• ACinputandDCoutputLEDindicators.

Features (cont’d):

• Shortcircuitandthermaloverloadprotection.

• Completewithpowersupply,powerdistributionmodule

(when applicable), enclosure, cam lock & battery leads.

• PowerON/OFFswitch.

Supervised models only:

• ACfailsupervision(form“C”contacts).

• Lowbatterysupervision(form“C”contacts).

SMP10C12X Series - Installation Guide

Summary of content (8 pages)

PAGE 1
SMP10C12X Series - Installation Guide Overview: These units convert a 115VAC 50/60Hz input into a regulated 12VDC output at up to 10 amp continuous supply current (see specifications). Battery Backup: • • • • • AC input and DC output LED indicators. Output Rating (amp) per Output Supervised 115VAC 50/60Hz Input Current (amp) 12VDC Total Output Current (amp) x x - x x x 10 10 10 10 3.5 2.5 3.5 2.5 3.5 2.5 x x x x x x x x 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.
PAGE 2
4. Connect devices to be powered: a. For Power Supply Board connect to the terminals marked [– DC +]. b. For Power Distribution Module(s) connect devices to be powered to the terminal pairs 1 to 4 marked [1P & 1N through 4P & 4N] (Fig. 3, pg. 4) 1 to 8 marked [1P & 1N through 8P & 8N] (Fig. 4, pg. 4) or 1 to 16 marked [1P & 1N through 16P & 16N] (Fig. 5, pg. 4), carefully observing correct polarity. *Note: Power switch is used to disconnect the L (HOT) terminal from the rest of the board.
PAGE 3
Fig. 2 CAUTION: De-energize unit prior to servicing. For continued protection against fire hazard replace fuse with the same type and rating, 15A, 32V. Power Supply Board OFF AC DC 15A L G N NC C NO NC C NO LOW BAT AC FAIL ON 5A 250V --- BAT + --- DC + 115 power mains Earth Ground Wire Strap (from Enclosure to Door) 12VDC Rechargeable Battery (optional) CAUTION: Optional rechargeable stand-by batteries must match the power supply output voltage setting.
PAGE 4
Power Distribution Module(s): Fig. 3 F1 Fig. 4 F1 F2 F3 F4 1 1 Used on PTC Models PD4 1P, 2P, 3P, 4P = FUSED OUTPUTS 1N, 2N, 3N, 4N = COMMON OUTPUTS Used on PTC Models POWER DISTRIBUTING UNIT LED 1P 2P 1N COMMON 2N POWER 3P 3N OUTPUTS DC Output to devices Fig.
PAGE 5
Power Supply Board Terminal Identification: Terminal Legend L, G, N – DC + *AC FAIL NC, C, NO Function/Description Connect 115VAC to these terminals: L to Hot, N to Neutral. 12VDC @ 10 amp continuous outputs. Indicates loss of AC power, e.g. connect to audible device or alarm panel. Relay normally energized when AC power is present. Contact rating 1 amp @ 120VAC / 28VDC Indicates low battery condition, e.g. connect to alarm panel. Relay normally energized when *Low Battery NC, DC power is present.
PAGE 6
Enclosure Dimensions for: SMP10C12X SMP10PMC12X SMP10PM12P4 SMP10PM12P4CB SMP10PM12P8 SMP10PM12P8CB SMP10PM12P16 SMP10PM12P16CB 13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm) 1.40” (36mm) 4.85” (123mm) 4.85” (123mm) 1.40” (36mm) 1.20” (31mm) 3.25” (83mm) 1.20” (31mm) 0.75” (19mm) 12.5” (318mm) 11.0” (279mm) 1.20” (31mm) 0.75” (19mm) 0.9375” (24mm) 1.40” (36mm) 1.40” (36mm) 5.10” (130mm) 5.10” (130mm) 13.0” (330mm) 5.10” (130mm) 6.5625” (167mm) 0.9375” (24mm) 3.25” (83mm) 3.
PAGE 7
Enclosure Dimensions for: SMP10C12XX SMP10PMC12XX 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm) 1.5” (38.1mm) 4.615” (117.22mm) 4.615” (117.22mm) 1.5” (38.1mm) 1.75” (44.45mm) 1.375” (34.925mm) 1.125” (28.575mm) 1.25” (31.75mm) 4.5” (114.3mm) 12.23” (310.64mm) 1.1” (27.94mm) 0.91” (23.114mm) 1.5” (38.1mm) 4.5” (114.3mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.91” (23.114mm) 2.0” (50.8mm) 1.5” (38.1mm) 15.5” (393.7mm) 2.0” (50.8mm) 5.0” (127.0mm) 5.0” (127.0mm) 1.1” (27.94mm) 1.25” (31.
PAGE 8
Notes: Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 web site: www.altronix.com, e-mail: info@altronix.com, Made in U.S.A. IISMP10C12X Series - Rev.