Power over the Ethernet PoE Managed Midspan Solution for Standard Network Infrastructure Installation Guide Models Include: NetWay8G - Eight (8) Port PoE Midspan Injector - 240W total power NetWay8GP - 8-Port Managed Hi-PoE Midspan Injector - 480W total power NetWay16G - Sixteen (16) Port PoE Midspan Injector - 480W total power I.T.E. 43KC DOC#: NETG Rev. 050719 More than just power.
Table of Contents: Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview: Altronix NetWay8G, NetWay8GP and NetWay16G Networked Managed Midspans provide PoE/PoE+/Hi PoE (up to 60W) power per port, and pass data at 10/100/1000 Mbps at distances up to 100m. Features also include an integral battery charger for applications requiring backup and embedded LINQ Technology to monitor, control, and report power and diagnostics from anywhere. Agency Listings: • UL 60950-1 • CE Input: • NetWay8G: • NetWay8GP/16G: Features: Information Technology Equipment.
6. When the use of stand-by batteries is required, they must be sealed lead acid or gel type. Connect four (4) 12VDC batteries in series to terminals marked [+ BAT –] (Fig. 2h, pg. 4), carefully observing polarity. Note: When batteries are not used a loss of AC will result in a loss of output voltage. 7. Manual Reset NetWay8G/NetWay8GP: Depress button for 3 seconds via pin hole marked RESET on front of unit. Manual Reset NetWay16G: This will require opening the unit.
Technical Specifications: Parameter Description No. of Ports NetWay8G: NetWay8GP: NetWay16G: Eight (8) PoE/PoE+ Ports (10/100/1000 Mbps). Eight (8) PoE/PoE+/Hi-PoE Ports (10/100/1000 Mbps). Sixteen (16) PoE/PoE+ Ports (10/100/1000 Mbps). Input Power Requirements NetWay8G: NetWay8GP: NetWay16G: 115VAC, 60Hz, 3.25A or 230VAC, 50/60Hz, 2.0A. 115VAC, 60Hz, 5.5A or 230VAC, 50/60Hz, 3.0A. 115VAC, 60Hz, 5.5A or 230VAC, 50/60Hz, 3.0A. Indicators Port Status LEDs.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient magnitude to constitute an electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Network Settings: In the IP Address Method field select the method that the IP Address for the NetWayG will be obtained (STATIC or DHCP), then follow the appropriate steps. Static: A. IP Address: Enter the IP address assigned to the NetWayG by the network administrator. B. Subnet Mask: Enter the Subnet of the network. C. Gateway: Enter the TCP/IP gateway of the network access point (router) being used (gateway configuration is required to properly receive emails from the device). D.
Rack Mount Installation Mounting Options: 1. Remove and discard factory installed screws from both sides of rack chassis (Fig. 5a). 2. Install mounting brackets (A) on the left and right side of rack chassis using the four (4) flat head screws (B) (included) (Fig. 5b). 3. Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 5c). Fig. 5 Fig. 5a Fig. 5b Top Fig. 5c Top Top Front Left Front Left Front Left B Remove A Wall Mount Installation 1.
