Power over the Ethernet PoE Managed Midspan Solution for Standard Network Infrastructure NetWay8GL - 8-Port Managed Hi-PoE Midspan Injector - 240W total power Installation Guide DOC#: NETGL Rev. 110719 More than just power.
Table of Contents: Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview: Altronix NetWay8GL Networked Managed Midspan provides PoE/PoE+/Hi PoE (up to 60W) power per port and passes data at 10/100/1000 Mbps at distances up to 100m. Features also include an integral battery charger for applications requiring backup and embedded LINQ Technology to monitor, control, and report power and diagnostics from anywhere. Features: Input: • 115VAC, 60Hz, 3.25A or 230VAC, 50/60Hz, 2.0A. Power: • Unit supplies PoE output voltage (55V) and up to 60W max. full power per port.
Fig. 2 2d NetWay8GL NetWay8GL - Front Panel 2a 2b 2c 2e 2f NetWay8GL - Rear Panel 2a 2b 2c 2d 2e 2f 2g 2h 2g 2h OUT 1-8: Structured cable to PoE compliant cameras/edge devices. IN 1-8: Structured cable to ethernet switch or video server. LED(s) 1-8: Port status LEDs. Reset: Restores unit to factory settings. USB Port: For future use. Ethernet: For future use. IEC 320 Connector: 115/230VAC (grounded line cord included).
Fig. 3 - NetWayXT/NetWayXTX NetWayXT NetWayXTX Structured Cable from NetWayG Made in U.S.A. NetwayXT Repeater Structured Cable from NetWayG Power LED www.altronix.com OUT Port Status PoE/PoE+ Structured Input LEDs Cable to LED PoE/PoE+ IP Camera/Device or next NetWayXTX Structured Cable to PoE IP Camera/ Edge Device or next NetWayXT I.T.E. 43KC Power PoE/PoE+ Output LED IN NetWayXT and NetWayXTX will work if the Midspan is set for 15W or 30W, but not 60W.
NetWay8GL Typical Applications: Fig. 4 Made in U.S.A. NetwayXT Repeater I.T.E. 43KC www.altronix.
e. HTTPS Port: Enter the HTTPS port number assigned to the NetWay8GL module by the network administrator to allow remote access and monitoring. The default inbound port setting is 443. Being encrypted and more secure, HTTPS is highly recommended for remote access. f. Click the button labeled Submit Network Settings. A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK. DHCP: a.
Rack Mount Installation Mounting Options: 1. Remove and discard factory installed screws from both sides of rack chassis (Fig. 5a). 2. Install mounting brackets (A) on the left and right side of rack chassis using the four (4) flat head screws (B) (included) (Fig. 5b). 3. Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 5c). Fig. 5 Fig. 5a Fig. 5b Top Fig. 5c Top Top Front Left Front Left Front Left B Remove A Wall Mount Installation 1.
