Power over the Ethernet PoE Managed Midspan Solution for Standard Network Infrastructure NetWay4BT - 4-Port Managed 802.3bt Midspan Injector - 360W total power NetWay8BT - 8-Port Managed 802.3bt Midspan Injector - 480W total power Installation Guide I.T.E. 43KC DOC#: NETBT Rev. 050719 More than just power.
Table of Contents: Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview: Altronix NetWay4BT/NetWay8BT Networked Managed Midspan provides PoE/PoE+/Hi PoE (up to 90W) power per port, and pass data at 10/100/1000 Mbps at distances up to 100m. Features also include an integral battery charger for applications requiring backup and embedded LINQ Technology to monitor, control, and report power and diagnostics from anywhere. Features: Agency Listings: • UL 60950-1 • CE Information Technology Equipment. European Conformity. Input: • 115VAC, 60Hz, 5.
Fig. 2 NetWay4BT - Front Panel 2a 2b 2c 2d NetWay8BT - Front Panel 2e 2f NetWay4BT/NetWay8BT - Rear Panel 2a 2b 2c 2d 2e 2f 2g 2h 2e 2f 2g 2h OUT1-4 (NetWay4BT), OUT 1-8 (NetWay8BT): Structured cable to PoE compliant cameras/edge devices. IN 1-4 (NetWay4BT), IN 1-8 (NetWay8BT): Structured cable to ethernet switch or video server. LED(s) 1-4 (NetWay4BT),1-8 (NetWay8BT): Port status LEDs. Reset: Restores unit to factory settings. USB Port: For future use. Ethernet: For future use.
Cable Type, Total Device Power, Data and Power Distance: Total Power Consumption Max. Data Distance Max. Power Distance CAT5e 15W 100m 846m CAT5e 30W 100m 423m CAT5e 60W 100m 211m CAT5e 75W 100m 185m CAT5e 90W 100m 158m Cable Type Note: Higher gauge wiring will allow for longer distances. Fig. 3 - NetWayXTG Fig. 3a Fig. 3b Made in U.S.A. PoE/PoE+ Output LED Structured Cable from Midspan or Endspan (10/100/1000) NetwayXTG Repeater www.altronix.
NetWay8BT Typical Applications: Fig. 4 Made in U.S.A. NetwayXTG Repeater www.altronix.
DHCP: A. After selecting DHCP in the IP Address Method field click the button labeled Submit Network Settings. A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK. Next, click on the button labeled Reboot Server. After rebooting the NetWay4BT/NetWay8BT will be set in the DHCP mode. The IP address will be assigned by the router when the NetWay4BT/NetWay8BT is connected to the network.
Rack Mount Installation Mounting Options: 1. Remove and discard factory installed screws from both sides of rack chassis (Fig. 5a). 2. Install mounting brackets (A) on the left and right side of rack chassis using the four (4) flat head screws (B) (included) (Fig. 5b). 3. Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 5c). Fig. 5 Fig. 5a Fig. 5b Top Fig. 5c Top Top Front Left Front Left Front Left B Remove A Wall Mount Installation 1.
