Installation Instructions

ManualsBrandsAltronix ManualsPOWERSingle Port PoE/PoE+ Injector for Standard Network

NetWay1/NetWay1X - 1 -

Overview:

Altronix NetWay1/NetWay1X are single port PoE/PoE+ injectors which provide power and passes data (e.g. video) for

PoE/PoE+ compliant devices. Devices may be located up to 100m from NetWay1/NetWay1X. To extend data distance for

an additional 100m use NetWayXT/NetWayXTX repeater modules.

General Specifications:

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and

authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.

Unit is intended to be used with a UL Listed Class 2 or LPS (limited power supply). NetWay1/NetWay1X is not intended

to be connected to outside plant leads and should be installed indoors within the protected premises.

NetWay1/NetWay1X is intended for indoor use only.

1. Mount NetWay1/NetWay1X in desired location utilizing the mounting hole (Figs. 1a and 2a, pg. 2). Use a proper

fastener and/or wall anchor when securing NetWay1/NetWay1X with screw through its mounting hole to the wall.

2. Connect 24VAC/24VDC to terminals marked [24VAC/VDC Input], (Figs. 1b and 2b, pg. 2). Use 22AWG-16AWG

wire for this connection. Input power should be a UL Listed Access Control power-limited power supply (for

UL294 applications) or Class 2 rated transformer/power supply (for UL60950-1 applications).

3. Connect structured cable from port marked [IN] on NetWay1/NetWay1X to the corresponding input of an

UL Listed ethernet switch or video server (Figs. 1b, 2b, pg. 2).

4. Connect structured cable from port marked [OUT] on the NetWay1/NetWay1X to PoE device (Figs. 1b, 2b, pg. 2).

All interconnected devices must be UL Listed.

5. Port status LED will illuminate indicating normal operation (Figs. 1c, 2b, pg. 2).

6. To initiate PoE shutdown connect 12VAC to 24VAC or 5VDC to 24VDC to the input terminals marked [PoE Shutdown]

on the NetWay1/NetWay1X (Figs. 1b, 2b, pg. 2). The PoE output voltage may be shutdown by manually applying

voltage in the rated range (PoE Shutdown Voltage Range in Specifications). Upon applying voltage the output will

drop to zero volts.

Removal of voltage from the shutdown terminals or applying zero volts to the shutdown terminals will allow the PoE

output to operate normally to supply power to PoE compliant devices.

Note: Return to normal operation from shutdown can take about 4 seconds. Although there is no output voltage to

power PoE devices during shutdown, data signals may still be present on the data pair lines of the CAT5 cable.

Agency Listings:

• NetWay1:

- UL/CUL Listed for Information Technology

Equipment (UL 60950-1). UL Listed for Access

Control Systems (UL294), Power over Ethernet

(PoE) for Access Control (UL294B).

- CUL Listed - CSA Standard C22.2 No.205-M1983,

Signal Equipment.

- CE approved.

• NetWay1X:

- UL/CUL Listed for Information Technology

Equipment (UL 60950-1).

- CUL Listed - CSA Standard C22.2 No.205-M1983,

Signal Equipment.

- CE approved.

Input:

• NetWay1: 24VAC @ 1.2 amp or 24VDC @ 1.2 amp.

• NetWay1X: 24VAC @ 1.5 amp or 24VDC @ 1.5 amp.

PoE/PoE+:

• NetWay1: IEEE 802.3af (15W) compliant.

• NetWay1X: IEEE 802.3at (30W) and

IEEE 802.3af (15W) compliant.

Features:

• PortstatusLED.

• PoEmanualshutdown(For UL 60950-1 applications

only) (see Technical Specifications table pg. 4).

• Autodetectionandprotectionoflegacy

non-PoE cameras/devices.

• Datarate:10/100BASE-Tcompliant.

• Compactinsulatedhousing.

Dimensions (W x L x H approx.):

NetWay1:

2.5” x 3.8” x 1” (63.5mm x 96.52mm x 25.4mm).

NetWay1X:

3.5” x 3.5” x 1” (88.89mm x 88.89mm x 25.4mm).

NetWay1 - Single Port PoE Injector for Standard NetWork Infrastructure

NetWay1X - Single Port PoE/PoE+ Injector for Standard NetWork Infrastructure

Rev. 032814

Installation Guide

Summary of content (4 pages)

PAGE 1
Rev. 032814 ® Installation Guide NetWay1 - Single Port PoE Injector for Standard NetWork Infrastructure NetWay1X - Single Port PoE/PoE+ Injector for Standard NetWork Infrastructure Overview: Altronix NetWay1/NetWay1X are single port PoE/PoE+ injectors which provide power and passes data (e.g. video) for PoE/PoE+ compliant devices. Devices may be located up to 100m from NetWay1/NetWay1X. To extend data distance for an additional 100m use NetWayXT/NetWayXTX repeater modules.
PAGE 2
NetWay1 Fig. 1 Fig. 1a Fig. 1b www.altronix.com www.altronix.com NetWay1 Single Port Injector (Midspan) NetWay1 24VAC/VDC, 1.2A Input 48VDC 15.4W max. per IEEE 802.3af Structured Cable from Network Switch 24VAC/ 24VDC Input Port Single Port Injector (Midspan) Status Equipment 92R2 Access Control PoE Injector Attack Class I 24VAC/VDC, 1.2A Input 48VDC 15.4W max. per IEEE 802.3af General Signaling Equipment 92R2 12VAC to 24VAC or 5VDC to 24VDC Input for PoE shutdown 24VAC/ 24VDC Input I.T.E.
PAGE 3
Typical Applications (NetWay1 and NetWay1X): Fig. 3 NetWay1/NetWay1X Port shutdown input PoE Camera CAT-5 100m 24VAC/ 24VDC input Fig. 4 Network Switch NetWay1/NetWay1X Port shutdown input NetWay1512 12VDC IP Camera CAT-5 100m 24VAC/ 24VDC input Video Monitor NVR/Network Server Network Switch NVR/Network Server Video Monitor Fig.
PAGE 4
Technical Specifications: Parameter No. of Ports Input power requirements Indicators PoE Shutdown Voltage and Current Range Description One (1) NetWay1: 24VAC @ 1.2 amp or 24VDC @ 1.2 amp. NetWay1X: 24VAC @ 1.5 amp or 24VDC @ 1.5 amp. Port Status LED, Power In LED (NetWay1X only). 5VDC to 24VDC or 12VAC to 24VAC Maximum current: 2mA for 5VDC Maximum current for higher voltages: 10mA Operating Ambient Temperature: NetWay1: UL60950-1: 32ºF to 104ºF (0ºC to 40ºC). UL294: 32ºF to 120.2ºF (0ºC to 49ºC).