Installation Manual

NetWay112 - 1 -
Overview:
Altronix NetWay112 is a single port PoE injector which provides power and passes data (e.g. video) for PoE compli-
ant devices. Devices may be located up to 100m from NetWay112. To extend data distance for an additional 100m use
NetWayXT/NetWayXTX repeater modules.
General Specifications:
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and
authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
Unit is intended to be used with a UL Listed Class 2 or LPS (limited power supply). NetWay112 is not intended to be
connected to outside plant leads and should be installed indoors within the protected premises.
NetWay112 is intended for indoor use only.
1. Mount NetWay112 in desired location utilizing the mounting hole (Fig. 1a, pg. 2). Use a proper fastener and/or wall
anchor when securing NetWay112 with screw through its mounting hole to the wall.
2. Connect UL Listed Class 2 or LPS (limited power supply) providing 12VDC/1.5A to 16VDC/1.1A to terminals
marked [+ DC --- Input], carefully observing polarity (Fig. 1b, pg. 2). Use 22AWG - 16AWG wire for this connection.
Input power should be a Access Control power supply or a transformer.
3. Connect structured cable from port marked [IN] on NetWay112 to the corresponding input of an UL Listed ethernet
switch or video server (Fig. 1b, pg. 2).
4. Connect structured cable from port marked [OUT] on the NetWay112 to the PoE device (Fig. 1b, pg. 2).
5. Port status LED will illuminate indicating normal operation (Fig. 1c, pg. 2).
6. To initiate PoE shutdown connect 12VAC to 24VAC or 5VDC to 24VDC to the input terminals marked [Power Shutdown]
on the NetWay112 (Fig. 1b, pg. 2). The PoE output voltage may be shut down by manually applying voltage in the
rated range (PoE Shutdown Voltage Range in Specifications). Upon applying voltage, the output will drop to zero
volts. Removal of voltage from the shutdown terminals or applying zero volts to the shutdown terminals will allow
the PoE output to operate normally to supply power to PoE compliant devices.
Note: Return to normal operation from shutdown can take about 4 seconds. Although there is no output voltage to
power PoE devices during shutdown, data signals may still be present on the data pair lines of the CAT5 cable.
Installing a NetWay1512 adapter for 12VDC IP cameras up to 13W:
1. Mount NetWay1512 in the proximity of IP camera (Fig. 3, pg. 3). Use velcro (supplied).
2. Connect structured cable from port marked [IN] on NetWay1512 to port marked [OUT] of NetWay112
(Fig. 3, pg. 3, Fig. 1b pg. 2).
3. Connect structured cable from port marked [OUT] on NetWay1512 to the IP camera/device (Fig. 3, pg. 3, Fig. 1b pg. 2).
4. Connect 12VDC output from NetWay1512 terminals marked [+ 12VDC --- ] to the power input of the
IP camera (Fig. 3, pg. 3). Polarity must be observed.
5. Power LED indicator will illuminate on NetWay1512 under normal conditions (Fig. 3, pg. 3).
Agency Listings:
• UL/CULListedforInformationTechnology
Equipment (UL 60950-1).
• CEapproved.
Input:
• 12VDC/1.5Ato16VDC/1.1A.
Data:
• One(1)PoEportprovidespowerandpassesdata
over ethernet (CAT5) cable up to 100m.
• Datarate:10/100Base-Tcompliant.
PoE:
• IEEE802.3af(15W)compliant.
Features:
• PortstatusLED.
• PoEmanualshutdownfeature allows for cameras and/or
edge devices to be reset. For UL 60950-1 applications
only (see Technical Specifications table pg. 4).
• Autodetectionandprotectionoflegacy
non-PoE cameras/devices.
• Datarate:10/100BASE-Tcompliant.
• Compactinsulatedhousing.
• Springterminals(InputandPoEshutdown).
Dimensions (W x L x H approx.):
2.5”x3.8”x1”(63.5mm x 96.52mm x 25.4mm).
NetWay112 - Single Port PoE Injector for Standard NetWork Infrastructure
®
Rev. 100614
Installation Guide