Installation Guide

ManualsBrandsAltronix ManualsAccess Control Power productsPower Supply/Charger w/Access Power Controllers

Access Power Controllers

with Power Supplies

Installation Guide for models:

Maximal3FD

- 12VDC @ 4.6 amp or 24VDC @ 5.2 amp.

- Sixteen (16) PTC protected power-limited outputs.

Maximal5FD

- 12VDC @ 8.6 amp.

- Sixteen (16) PTC protected power-limited outputs.

Maximal7FD

- 24VDC @ 9.2 amp.

- Sixteen (16) PTC protected power-limited outputs.

Rev. SFD051313 More than just power.™

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Altronix Corp.

140 58th St. Brooklyn, NY

Summary of content (12 pages)

PAGE 1
Access Power Controllers with Power Supplies Installation Guide for models: Maximal3FD - 12VDC @ 4.6 amp or 24VDC @ 5.2 amp. - Sixteen (16) PTC protected power-limited outputs. Maximal5FD - 12VDC @ 8.6 amp. - Sixteen (16) PTC protected power-limited outputs. Maximal7FD - 24VDC @ 9.2 amp. - Sixteen (16) PTC protected power-limited outputs. Altronix Corp. 140 58th St. Brooklyn, NY Rev. SFD051313 More than just power.™ Installing Company: ______________________ Service Rep.
PAGE 2
MaximalFD Series Overview: MaximalFD Access Power/Controllers distribute and switch power to access control systems and accessories. They convert a 120VAC 60Hz input into sixteen (16) independently controlled 12VDC or 24VDC PTC protected protected outputs. The outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Keypad, Push Button, REX PIR, etc.
PAGE 3
• Maximum charge current 1.54 amp. • Automatic switch over to stand-by battery when AC fails. Transfer to stand-by battery power is instantaneous with no interruption. • Supervised Fire Alarm disconnect (latching or non-latching) 10K EOL resistor. Operates on a normally open (NO) or normally closed (NC) trigger. • AC fail supervision (form “C” contacts). • Battery fail and presence supervision (form “C” contacts). • Low power shutdown.
PAGE 4
ACM8CB Fire Alarm Interface options (Figs. 5-9, pg. 9): A normally closed [NC] or normally open [NO] input trigger from a fire alarm control panel or a polarity reversal input from an FACP signaling circuit will affect selected outputs. To enable FACP Disconnect for an output, turn the corresponding switch(es) [SW1-SW8] OFF on each ACM8CB board. To disable FACP disconnect for an output, turn the corresponding switch(es) [SW1-SW8] ON on each ACM8CB board.
PAGE 5
Power Supply Board LED Diagnostics: Red (DC) ON ON OFF OFF Green (AC/AC1) ON OFF ON OFF Power Supply Status Normal operating condition. Loss of AC. Stand-by battery supplying power. No DC output. Loss of AC. Discharged or no stand-by battery. No DC output. Access Power Controller LED Diagnostics: LED LED 1- LED 8 (Red) Trg (Green) ON Output relay(s) energized. FACP input triggered (alarm condition). OFF Output relay(s) de-energized. FACP normal (non-alarm condition).
PAGE 6
Power Supply Board Stand-by Battery Specifications: Battery Maximal3FD Maximal5FD 7AH 10 Mins./6 amp 5 Mins./10 amp 12AH 30 Mins./6 amp* 30 Mins./10 amp* 40AH Over 4 Hours/6 amp* Over 2 Hours/10 amp* 65AH Over 4 Hours/6 amp* Over 4 Hours/10 amp* *Only these configurations can be utilized in ULC-S319 installations. Maximal7FD 5 Mins./10 amp 30 Mins./10 amp* Over 2 Hours/10 amp* Over 4 Hours/10 amp* Power Supply Board Output Voltage Settings: Fig. 1a OFF - 24V ON - 12V ON ON Fig.
PAGE 7
Fig. 3 Maximal3FD, Maximal5FD, and Maximal7FD.
PAGE 8
NEC Power-Limited Wiring Requirements: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. Your specific application may require different conduit knockouts to be used.
PAGE 9
Fig. 5 FACP Hook-Up Diagrams: Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm condition): CUT JUMPER INTERFACE FACP OUTPUT EOL -- FROM FACP OUTPUT + CIRCUIT NO C NC FACP TRG Fig. 6 Normally Open - Non-Latching FACP Fig. 7 Normally Open FACP Latching trigger input trigger input: with reset: (This output has not been evaluated by UL) INTERFACE TRG N.O. TRIGGER INPUT NC N.O. TRIGGER INPUT N.C. RESET SWITCH JUMPER NO C NO C NC FACP TRG Fig.
PAGE 10
Notes: - 10 - Maximal3FD/Maximal5FD/Maximal7FD Access Power Controllers (PTC)
PAGE 11
Notes: Maximal3FD/Maximal5FD/Maximal7FD Access Power Controllers (PTC) - 11 -
PAGE 12
Enclosure Dimensions (H x W x D approximate): 26” x 19” x 6.25” (660.4mm x 482.6mm x 158.75mm) 19” (482.6mm) 2” (50.8mm) 4” (101.6mm) 7” (177.8mm) 4” (101.6mm) 2” (50.8mm) 6.25” (158.75mm) TOP 1.25” (31.75mm) 0.85” (21.59mm) 19” (482.6mm) 8.9” (226.06mm) 1.25” (31.75mm) 0.85” (21.59mm) 8.4” (213.36mm) 1.5” (38.1mm) 1.5” (38.1mm) 1.5” (38.1mm) 5” (127mm) 8.5” (215.9mm) 7” (177.8mm) 7.5” (190.5mm) 7.5” (190.5mm) 26” (660.4mm) 8.5” (215.9mm) 26” (660.4mm) 26” (660.