Installation Guide

ManualsBrandsAltronix ManualsAccess Control Power products2 Pwr Supply/Charger w/ Access Power Controllers

Access Power Controllers

with Power Supplies

Installation Guide for Models:

Rev. DFD051613 More than just power.™

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Maximal11FD

- Power Supply 1:

12VDC @ 3.3 amp or 24VDC @ 3.6 amp.

- Power Supply 2:

12VDC @ 3.3 amp or 24VDC @ 3.6 amp.

- Sixteen (16) PTC protected

power-limited outputs.

Maximal33FD

- Power Supply 1:

12VDC @ 5.3 amp or 24VDC @ 5.6 amp.

- Power Supply 2:

12VDC @ 5.3 amp or 24VDC @ 5.6 amp.

- Sixteen (16) PTC protected

power-limited outputs.

Maximal55FD

- Power Supply 1: 12VDC @ 9.3 amp.

- Power Supply 2: 12VDC @ 9.3 amp.

- Sixteen (16) PTC protected

power-limited outputs.

Maximal77FD

- Power Supply 1: 24VDC @ 9.6 amp.

- Power Supply 2: 24VDC @ 9.6 amp.

- Sixteen (16) PTC protected

power-limited outputs.

Maximal75FD

- Power Supply 1: 12VDC @ 9.3 amp.

- Power Supply 2: 24VDC @ 9.6 amp.

- Sixteen (16) PTC protected

power-limited outputs.

Altronix Corp.

140 58th St. Brooklyn, NY

Summary of content (12 pages)

PAGE 1
Access Power Controllers with Power Supplies Installation Guide for Models: Maximal11FD Power Supply 1: 12VDC @ 3.3 amp or 24VDC @ 3.6 amp. Power Supply 2: 12VDC @ 3.3 amp or 24VDC @ 3.6 amp. Sixteen (16) PTC protected power-limited outputs. Maximal33FD Power Supply 1: 12VDC @ 5.3 amp or 24VDC @ 5.6 amp. Power Supply 2: 12VDC @ 5.3 amp or 24VDC @ 5.6 amp. Sixteen (16) PTC protected power-limited outputs. Maximal55FD Power Supply 1: 12VDC @ 9.3 amp. Power Supply 2: 12VDC @ 9.3 amp.
PAGE 2
MaximalFD Series Overview: MaximalFD Access Power/Controllers distribute and switch power to access control systems and accessories. They convert a 120VAC 60Hz input into sixteen (16) independently controlled 12VDC or 24VDC PTC protected outputs. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc.
PAGE 3
MaximalFD Series Features: ACM8CB Access Power Controller Modules: • Sixteen (16) independently trigger controlled outputs. Output options: a) Sixteen (16) Fail-Safe filtered power outputs. b) Sixteen (16) Fail-Secure filtered power outputs. c) Any combination of the above. • Sixteen (16) Access Control System trigger inputs. Input trigger options: a) Sixteen (16) normally open (NO) dry trigger inputs. b) Sixteen (16) open collector inputs. c) Any combination of the above.
PAGE 4
3. Select desired DC output voltage by setting SW1 to the appropriate position on the power supply board (Maximal11FD and Maximal33FD), (Fig. 1, pg. 7). Maximal55FD power supply is factory set at 12VDC. Maximal77FD power supply is factory set at 24VDC. Maximal75FD consists of one (1) power supply board that is factory set at 12VDC, and one (1) power supply board that is factory set at 24VDC. 4. Measure the output voltage of the unit before connecting any devices to ensure proper operation.
PAGE 5
15. Multiple power supply inputs (Fig. 2, pg. 7) (Not evaluated by UL): When using an additional Listed external power supply, jumpers J1 and J2 located on corresponding ACM8CB board must be cut (Fig. 2c, pg. 7 and Fig. 5, pg. 10). Connect external Listed power-limited access control power supply to the terminals marked [- Control +] (These terminals are paralleled to the - Power + terminals). When using DC power supplies, polarity must be observed.
PAGE 6
Power Supply Board Terminal Identification: Terminal Legend L, N + DC – Trigger EOL Supervised NO, GND RESET + AUX – AC FAIL NC, C, NO BAT FAIL NC, C, NO + BAT – Function/Description Connect 120VAC 60Hz to these terminals: L to hot, N to neutral. Do not use terminal marked [G] Factory connected to ACM8CB board. Fire Alarm Interface trigger input from a short or FACP. Trigger inputs can be normally open, normally closed from an FACP output circuit (power-limited input) (Fig. 3, pg. 8).
PAGE 7
Power Supply Board Stand-by Battery Specifications: Battery Maximal11FD Maximal33FD 7AH 30 Mins./4 amp* 10 Mins./6 amp 12AH 35 Mins./4 amp* 30 Mins./6 amp* 40AH Over 4 Hours/4 amp* Over 4 Hours/6 amp* 65AH Over 4 Hours/4 amp* Over 4 Hours/6 amp* *Only these configurations can be utilized in Canadian installations. Maximal55FD, Maximal75FD, and Maximal77FD 5 Mins./10 amp 30 Mins./10 amp* Over 2 Hours/10 amp* Over 4 Hours/10 amp* Power Supply Board Output Voltage Settings: Fig. 1 ON ON Fig.
PAGE 8
Fig. 3 --- DC + OFF --- 24V ON --- 12V ON Tamper Switch --- BAT + Power Supply Board AC1 5A 250V L G N AC FAIL BAT FAIL AC DELAY SHUTDOWN O N NC C NO NC C NO AC DC 1 min. 2 hr.
PAGE 9
NEC Power-Limited Wiring Requirements: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non powerlimited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. Your specific application may require different conduit knockouts to be used.
PAGE 10
FACP Hook-Up Diagrams: Fig. 5 Optional hook-up using two (2) isolated power Fig. 6 supply inputs (Only applicable on Maximal11FD) (Not evaluated by UL): Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm condition): CUT JUMPER CUT JUMPERS J1 AND J2 J2 J1 ISOLATED POWER INPUT 12 OR 24 VAC OR VDC (ACM8 POWER) TRG N.O. TRIGGER INPUT NC N.O.
PAGE 11
Notes: - 11 - Maximal11FD/Maximal33FD/Maximal55FD/Maximal77FD/Maximal75FD Access Power Controllers (PTC)
PAGE 12
Enclosure Dimensions (H x W x D approximate): 26” x 19” x 6.25” (660.4mm x 482.6mm x 158.75mm) 19” (482.6mm) 2” (50.8mm) 4” (101.6mm) 7” (177.8mm) 4” (101.6mm) 2” (50.8mm) 6.25” (158.75mm) TOP 1.25” (31.75mm) 0.85” (21.59mm) 19” (482.6mm) 8.9” (226.06mm) 1.25” (31.75mm) 0.85” (21.59mm) 8.4” (213.36mm) 1.5” (38.1mm) 1.5” (38.1mm) 1.5” (38.1mm) 5” (127mm) 8.5” (215.9mm) 7” (177.8mm) 7.5” (190.5mm) 7.5” (190.5mm) 26” (660.4mm) 8.5” (215.9mm) 26” (660.4mm) 26” (660.