Installation Guide

ManualsBrandsAltronix ManualsAccess Control Power productsAccess Power Controller Kit BC750 Enclosure with eFlow104NB, (2) ACM8, PD16W

Access Power Controllers

Rev. MFKF_083019

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

More than just power.™

Installation Guide

MaxFit7F8AP

Fully assembled kit includes:

- One (1) eFlow104NB - Power Supply/Charger

- One (1) ACM8 - Fuse Protected Access Power Controller

- One (1) PD8UL - Fuse Protected Power Distribution Module

- BC750 enclosure

MaxFit7F16AP

Fully assembled kit includes:

- One (1) eFlow104NB - Power Supply/Charger

- Two (2) ACM8 - Fuse Protected Access Power Controllers

- One (1) PD16W - Fuse Protected Power Distribution Module

- BC750 enclosure

MaxFit7F8APS

Fully assembled kit includes:

- One (1) eFlow104NB - Power Supply/Charger

- One (1) ACM8 - Fuse Protected Access Power Controller

- One (1) PDS8 - Dual Input Fuse Protected

Power Distribution Module

- One (1) VR6 - Voltage Regulator

- BC750 enclosure

MaxFit7F16APS

Fully assembled kit includes:

- One (1) eFlow104NB - Power Supply/Charger

- Two (2) ACMS8 - Dual Input Fuse Protected

Access Power Controllers

- One (1) VR6 - Voltage Regulator

- One (1) PD16W - Fuse Protected Power Distribution Module.

- BC750 enclosure

Summary of content (8 pages)

PAGE 1
Access Power Controllers MaxFit7F8AP Fully assembled kit includes: - One (1) eFlow104NB - Power Supply/Charger One (1) ACM8 - Fuse Protected Access Power Controller One (1) PD8UL - Fuse Protected Power Distribution Module BC750 enclosure MaxFit7F16AP Fully assembled kit includes: - One (1) eFlow104NB - Power Supply/Charger Two (2) ACM8 - Fuse Protected Access Power Controllers One (1) PD16W - Fuse Protected Power Distribution Module BC750 enclosure MaxFit7F8APS Fully assembled kit includes: - On
PAGE 2
Overview: Altronix fused Access Power Controller kits distribute and switch power to access control systems and accessories. They convert a 120VAC 60Hz input into eight (8) or sixteen (16) independently controlled 12VDC or 24VDC fuse protected outputs. These Fail-Safe/ Fail-Secure power outputs may be converted to dry form “C” contacts. Relays are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Keypad, Push Button, REX PIR, etc.
PAGE 3
MaxFit7F8AP: NEC Power-Limited Wiring Requirements Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. Your specific application may require different conduit knockouts to be used.
PAGE 4
MaxFit7F16AP: NEC Power-Limited Wiring Requirements Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. Your specific application may require different conduit knockouts to be used.
PAGE 5
MaxFit7F8APS: NEC Power-Limited Wiring Requirements Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. Your specific application may require different conduit knockouts to be used.
PAGE 6
MaxFit7F16APS: NEC Power-Limited Wiring Requirements Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. Your specific application may require different conduit knockouts to be used.
PAGE 7
eFlow Power Supply/Chargers can be Controlled and Monitored while Reporting Power/Diagnostics from Anywhere over the Network... LINQ2 - Network Communication Module LINQ2 provides remote IP access to real-time data from eFlow power supply/chargers to help keep systems up and running at optimal levels.
PAGE 8
MaxFit Enclosure Dimensions (approximate): 20.5” x 16.5” x 6.25” (520.7mm x 419.1mm x 158.8mm) 1.25” (31.8mm) 7.00” 177.8mm 7.00” 177.8mm 1.25” (31.8mm) 1.25” (31.8mm) 6.25” (158.8mm) 1.25” (31.8mm) 16.50” (419.1mm) 0.75” (19.1mm) 1.50” (38.1mm) 1.25” (31.8mm) 1.00” (25.4mm) 1.25” (31.8mm) 1.50” (38.1mm) 8.75” (222.3mm) 8.75” (222.3mm) 20.50” (520.7mm) 8.75” (222.3mm) 8.75” (222.3mm) 0.569” (14.5mm) 1.50” (38.1mm) 1.50” (38.1mm) 1.25” (31.8mm) 1.25” (31.8mm) 1.25” (31.8mm) 1.25” (31.