UTP Power Injector Installation Guide Models Include: HubWayEXP - Sixteen (16) Channel UTP Power Injector Rev. 011810 More than just power.
Overview: Altronix HubWayEXP UTP Power Injector supplies power combined with pass through video and data for up to 16 cameras from Altronix HubWay Active UTP Transceiver Hubs. Unit allows for video transmission of up to 16 cameras over four CAT-5 or higher structured cables from HubWay Active Transceiver Hubs. The HubWayEXP units are designed for installation at the IDF (Intermediate Distribution Frame) or MDF (Main Distribution Frame). Input: Specifications: Visual Indicators: • 115VAC 60Hz, 2.
HubWayDv Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 1b, 1d, pg. 3). 10. Measure the output voltage at each Video Balun/Combiner (Figs. 1b, 1d, pg. 3) before making connections to each camera to insure proper operation and avoid possible damage. 11. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 6, pg. 7). 12. Connect power outputs of HubWayAv or HubWayDv Video Balun/Combiners to power inputs of cameras (Figs. 1a-1d, pg. 3).
-4- HubWayEXP UTP Power Injector Rear OFF RESET Front Fig. 3 1 2 3 4 + DATA -1-8 CH 1-4 5 6 7 8 28VAC OFF 24VAC CH 5-8 3c - Output voltage switches: Selects 24VAC/28VAC/ OFF for each output. 3b - LED(s) 1-16: Power indicators. 3a - Port(s) 1-16: CAT-5 or higher structured cable to cameras 1-16. 9 10 11 3d - Video 1-4: Single CAT-5 or higher structured cable out to HubWayEX16/EX32 or HubWayEX16S enables transmission of up to four (4) video signals.
Typical Applications: Fig. 4 Head End Equipment (DVR) RS485 Monitor Video Data HubWayEX16S Rear Panel 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 AC POWER HubWayEX16S - Front Panel RESET 1 2 3 4 OFF CH 1-4 5 6 7 8 CH 5-8 9 10 11 12 CH 9-12 DATA 1-8 13 14 15 16 CH 13-16 DATA 9-16 HubWayEXP - Front Panel RESET 1 2 3 4 OFF CH 1-4 5 6 7 8 9 CH 5-8 28VAC OFF 24VAC + DATA -1-8 10 11 12 CH 9-12 + DATA -9-16 13 14 15 16 CH 13-16 28VAC OFF 24VAC Max.
Typical Applications: Fig.
1U EIA 19” Rack Mount Chassis Mechanical Drawing & Dimensions: 1.625”H x 19.125”W x 8.5”D REAR 1.625" AC POWER TOP & BOTTOM 17.625" 8.5" FRONT RESET 1 OFF 2 3 4 CH 1-4 + DATA -1-8 5 6 7 8 9 CH 5-8 28VAC OFF 24VAC 10 11 12 CH 9-12 13 14 15 16 + DATA -9-16 CH 13-16 28VAC OFF 24VAC 19.125" .75" RESET Fig. 6 Illuminated master power disconnect circuit breaker: • OFF position Circuit breaker tripped – Switch not illuminated. • RESET (ON) position – Switch illuminated.
Mounting Options: Rack Mount Installation 1- Remove and discard factory installed screws from both sides of rack chassis (Fig. 7a). 2- Install mounting brackets (A) on the left and right side of rack chassis using the four (4) flat head screws (B) (included) (Fig. 7b). 3- Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 7c). Fig. 7 Fig. 7a Fig. 7b Fig.
