Video • Data Active UTP Transceiver Hub Installation Guide Models Include: HubWayEX16 - Sixteen (16) Camera Channels HubWayEX32 - Thirty-two (32) Camera Channels Rev. 011810 More than just power.
Overview: Altronix HubWayEX16/EX32 Active UTP Transceiver Hub employs automatic gain control (AGC) to transmit UTP video, RS422/RS485 data over a single CAT-5 or higher structured cable. Units provide either 16 or 32 camera channels in a space saving 1U EIA 19” rack mount chassis which may be rack, wall or shelf mounted. Video transmission range is up to one mile max. per channel. Units are compatible with fixed or PTZ cameras.
HubWayEX16/HubWayEX32 Active Hub Unit 15 31 16 32 30 14 HubWayEX16 Rear 29 13 CH 29 - 32 CH 13 - 16 28 12 EX 27 11 26 10 25 9 CH 25 - 28 CH 9 - 12 EX 27 7 26 6 25 5 18 17 19 3 CH 21 - 24 CH 5 - 8 2 1 5 20 24 4 21 ACTIVE 4 22 6 23 3 23 7 24 8 22 2 21 1 7 15 8 16 14 6 13 5 1 3 CH 13 - 16 CH 5 - 8 2 CH 17 - 20 27 11 13 28 30 14 DATA 29 ACTIVE 12 12 4 5 6 11 3 7 8 10 2 9 1 10 CH 9 - 12 CH 1 - 4 9 11 12 14 DATA 1
9. Connect one (1) end of a CAT-5 or higher structured cable into the RJ45 jack marked [DATA] of the HubWayEX16/EX32 (Fig. 1e, pg. 3). Connect the opposite end of the CAT-5 or higher structured cable into the RJ45 jack marked [DATA] of HubWayEXP (Fig. 4, pg. 5) or [DATA 1-4] of the HubSat4D/Di (Fig. 5, pg. 6). Note: When using fixed cameras disregard this step. Repeat steps 8 and 9 for cameras 5-8, 9-12, 13-16, 17-20, 21-24, 25-28, 29-32.
Typical Applications: Fig.
Typical Applications: Fig.
1U EIA 19” Rack Mount Chassis Mechanical Drawing & Dimensions: 1.625”H x 19.125”W x 8.5”D REAR 1.625" 16 32 15 31 14 30 13 29 CH 13 - 16 12 CH 29 - 32 28 11 27 10 26 9 25 CH 9 - 12 8 CH 25 - 28 28 7 27 6 5 26 25 CH 5 - 8 4 CH 21 - 24 24 3 23 2 22 1 CH 1 - 4 21 DATA CH 17 - 20 AC POWER TOP & BOTTOM 17.625" 8.5" FRONT EX 1 2 3 4 5 6 7 8 9 10 11 ACTIVE 17 18 19 20 21 12 13 14 15 16 30 31 32 ACTIVE 22 23 24 25 26 27 28 29 19.
Mounting Options: Rack Mount Installation 1- Remove and discard factory installed screws from both sides of rack chassis (Fig. 7a). 2- Install mounting brackets (A) on the left and right side of rack chassis using the four (4) flat head screws (B) (included) (Fig. 7b). 3- Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 7c). Fig. 7 Fig. 7b Fig. 7a Fig.
