Video • Data Active UTP Transceiver Hub Installation Guide HubWayEX16S - Sixteen (16) Camera Channels Rev. 011810 More than just power.
Overview: Altronix HubWayEX16S Active UTP Transceiver Hub employs automatic gain control (AGC) to transmit UTP video and RS422/RS485 data over a single CAT-5 or higher structured cable. Unit provides 16 camera channels in a space saving 1U EIA 19” rack mount chassis which may be rack, wall or shelf mounted. Video transmission range is up to one mile max. per channel. Units are compatible with fixed or PTZ cameras.
9. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 6, pg. 7) and measure the output voltage at the power output of each Video Balun/Combiner (Figs. 1b, 1d, pg. 3) before powering each camera to insure proper operation and avoid possible damage. • For AC cameras - HubWayAv - Terminals marked [AC POWER] (Figs. 1a, 1b, pg. 3). • For DC cameras - HubWayDv - Terminals marked [--- 12VDC +] (Figs. 1c, 1d, pg. 3). 10.
-4- 16 15 1 14 2 OFF RESET 1 2 3d - BNC Connector: Video outputs to head end equipment (DVR). Rear OFF RESET Front 3 3 13 4 4 11 5 6 10 7 9 8 DATA 1-8 5 6 7 8 3e - LED(s) 1-16: Video signal indicators. CH 1-4 12 DATA 1-8 CH 1-4 CH 5-8 CH 5-8 8 8 7 7 9 3b - Channels 1-4, Channels 5-8, Channels 9-12 & Channels 13-16: CAT-5 or higher structured cable from optional HubSat4D/4Di enables video transmission from up to four (4) cameras.
Typical Applications: Fig. 4 Head End Equipment (DVR) RS485 Monitor Video Data Rear 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 AC POWER RESET 1 2 3 4 CH 1-4 5 6 7 8 CH 5-8 9 10 11 DATA 1-8 OFF 12 CH 9-12 13 14 15 16 CH 13-16 DATA 9-16 Front CAT-5 CAT-5 Video Power Max. video 3000 ft.
Typical Application Utilizing HubSat4D/Di as a Remote Accessory Module with HubWayEX16S UTP Transceiver Hub: Fig.
1U EIA 19” Rack Mount Chassis Mechanical Drawing & Dimensions: 1.625”H x 19.125”W x 8.5”D REAR 1.625" 16 14 15 13 12 11 10 9 8 7 6 5 4 3 2 1 AC POWER TOP & BOTTOM 17.625" 8.5" FRONT 1 2 3 4 CH 1-4 5 6 7 8 CH 5-8 9 DATA 1-8 10 11 12 CH 9-12 13 14 15 16 CH 13-16 DATA 9-16 19.125" .75" HubWayEX16S Active Hub Unit (ON) Fig. 6 Illuminated master power disconnect circuit breaker: • OFF position Circuit breaker tripped – Switch not illuminated.
Mounting Options: Rack Mount Installation 1- Remove and discard factory installed screws from both sides of rack chassis (Fig. 7a). 2- Install mounting brackets (A) on the left and right side of rack chassis using the four (4) flat head screws (B) (included) (Fig. 7b). 3- Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 7c). Fig. 7 Fig. 7b Fig. 7a Fig.
