Installation Instructions
- 4 - HubSat8Di
The total cable distance must not exceed 750 ft. for video transmission between the HubSat8Di and each camera.
Repeat this step for all other camera channels [PVD2-4] on Circuit Board A and [PVD1-4] on Circuit Board B.
3. SetilluminatedmasterpowerdisconnectcircuitbreakertotheRESET(ON)position(Fig.3a,pg.6).Power
LEDs(Green)oftheHubSat8DiwillilluminatewhenACpowerispresent(Fig.1e,pg.5)and HubWayAv or
HubWayDvVideoBalun/CombinerLEDswillilluminateindicatingpowerispresent(Fig.2b,2d,pg.6).
4. Measure the output voltage at each Video Balun/Combiner (Figs.2b,2d,pg.6) before making connections to
each camera to ensure proper operation and avoid possible damage.
5. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig.3a,pg.6).
6. Connect power outputs of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to power inputs
of the cameras (Figs.2a-2e,pg.6).Polarity must be observed.
• HubWayAv/HubWayAv2-Terminalsmarked[ACPOWER](Figs.2a,2b,2e,pg.6).
• HubWayDv-Terminalsmarked[–12VDC+](Figs.2c,2d,pg.6).
7. Connect the terminals marked [+ DATA -- ] of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to
the data input terminals of cameras for PTZ control (Figs.2b-2e,pg.6). Polarity must be observed.
When using fixed cameras disregard this step.
8. Connect the BNC connector of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to the BNC video
outputs of the cameras (Figs.2b-2d,pg.6).
9. SetilluminatedmasterpowerdisconnectcircuitbreakertotheRESET[ON]position(Fig.3a,pg.6).
10. ThepowerLEDs(Green)oftheHubSat8DiwillilluminatewhenACpowerispresent(Fig.1e,pg.5).
Note:IfanyofthepowerLEDsarenotilluminatedthecausemaybeduetothefollowing:
a. AC mains fail.
b. Illuminated master power disconnect circuit breaker is tripped.
c. An individual power output voltage switch is set to the OFF position (Fig.1d,pg.5).
e. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs.
ToresetthePTC:
1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must
remain in the OFF position for approximately 2 minutes in order for the PTC to reset (Fig.1d,pg.5).
2. Eliminatethetroublecondition(shortcircuitoroverload).
3. Set the voltage output selector switch for either 24VAC or 28VAC (Fig.1d,pg.5).
Alternate 24VAC fixed camera hookup (Fig. 5a, pg. 7).
After completing steps 1-5 of Installation Instructions Remote Accessory Module for use with HubWay, HubWayLD or
HubWayLDH UTP Transceiver Hubs proceed with the following.
1. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig.3a,pg.6).
2. Connect one end of the coaxial cable to the BNC connector marked [Video1] on Circuit Board A (Fig.1a,pg.5).
Connect the opposite end of the coaxial cable to the BNC video output of camera 1 (Fig.5a,pg.7).
3. SetilluminatedmasterpowerdisconnectcircuitbreakertotheRESET(ON)position(Fig.3a,pg.6)measure the
output voltage at the terminal pair marked [AUX1] on Circuit Board A to ensure proper operation and
avoid possible damage (Fig.1b,pg.5).
4. Connect the power output terminal pair marked [AUX1] on Circuit Board A to the power inputs of camera 1
(Fig.1c,pg.5). Repeat steps 1-3 for each additional camera [AUX2-4].