Installation Instructions

- 2 - HubSat8Di
Overview:
Altronix HubSat8Di Passive UTP Transceiver Hub w/Integral Camera Isolated Power transmits UTP video, RS422/RS485
data and power over a single CAT-5 or higher structured cable. Unit provides 8 camera channels in a wall mount enclosure.
Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras
when utilizing Altronix HubWayAv or HubWayDv Video Balun/Combiners. In addition, the unit features individually select-
able 24VAC or 28VAC PTC protected outputs with surge suppression. Optionally, the HubSat8Di can be used as an accessory
module to transmit video from up to 8 cameras over two (2) separate CAT-5 or higher structured cables back to the HubWay,
HubWayLD or HubWayLDH Passive and Active UTP Transceiver Hubs. In addition, the HubSat8Di provides power to these
cameras locally to eliminate the possibility of voltage drop associated with long cable runs.
Input:
• 115VAC 60Hz, 2.5 amp.
Video:
• Eight(8)channelsofqualityvideoovertwistedpair
up to a distance of 750 ft. per channel.
• Eight(8)75ohmvideooutputs.
Data:
• RS422/RS485 data input.
Power:
• Individuallyselectable24VACor28VACpower
outputs with OFF position.
• Unitprovidesupto1ampmax.perchannel,notto
exceed a total of 8 amp maximum current.
Power (cont.):
• PTCprotectedoutputsare rated @ 1 amp per channel.
• Surgesuppression.
Visual Indicators:
• Eight(8)powerLEDindicators.
Enclosure Dimensions (H x W x D approximate):
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)
Optional Accessories:
• VideoBalun/Combiners:
- HubWayAv - for use with 24VAC cameras.
- HubWayAv2 - for use with 24VAC cameras.
- HubWayDv - for use with 12VDC cameras.
Specifica tions:
HubSat82Di
• HubSat8Di with eight (8) HubWayAv
Video Balun/Combiners for 24VAC Cameras.
HubSat83Di
• HubSat8Di with eight (8) HubWayDv
Video Balun/Combiners for 12VDC Cameras.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This
installation should be made by qualified service personnel and should conform to all local codes.
Installation Instructions:
HubSat8Di Passive UTP Transceiver Hub with Integral Isolated Camera Power.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install two fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (EnclosureDimensions,pg.8).
Secure green wire lead to earth ground.
2. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig.3a,pg.6).
3. Connect 115VAC 60Hz to the black and white flying leads of open frame transformer. Secure ground
wire (Green) to earth ground (Fig.3,pg.6).
4. S elect 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat Circuit Board A and
HubSat Circuit Board B (Fig.3,pg.6) with the corresponding output voltage switches. Select OFF position when
servicing or installing individual cameras (Fig.1d,pg.5).
5. Connect the BNC video outputs marked [Video 1-4] on Circuit Board A and [Video 1-4] on Circuit Board B to the
 correspondingvideoinputsontheheadendequipment(DVR)(Fig.1a,pg.5).
6. Connect terminals marked [+ Data --- ] on Circuit Board A and Circuit Board B (polarity must be observed) to the
 RS422/RS485outputoftheheadendequipment(DVR)(Fig.1f,pg.5).
Note: The Data input terminals of Circuit Board A and Circuit Board B must be wired in parallel
for proper operation. When using fixed cameras disregard this step.
Additional Models: