Installation Instructions

- 4 - HubSat4Di
6. Connect power outputs of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to power inputs of the
cameras (Figs. 2a-2e, pg. 5). Polarity must be observed.
 • HubWayAv/HubWayAv2-Terminalsmarked[ACPOWER](Figs. 2a, 2b, 2e, pg. 5-6).
 • HubWayDv/-Terminalsmarked[–12VDC+](Figs. 2c, 2d, pg. 5).
7. Connect the terminals marked [+ DATA --]ofHubWayAv,HubWayAv2 or HubWayDv Video Balun/Combiners to
the data input terminals of cameras for PTZ control (Figs. 2b-2e, pg. 5-6). Polarity must be observed. When using
fixed cameras disregard this step.
8. Connect the BNC connector of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to the BNC video
outputs of cameras (Figs. 2b-2e, pg. 5-6).
9. SetilluminatedmasterpowerdisconnectcircuitbreakertotheRESET(ON)position(Fig. 4a, pg. 6).
10. ThepowerLEDs(Green)oftheHubSat4DiwillilluminatewhenACpowerispresent(Fig. 1e, pg. 5).
Note:IfanyofthepowerLEDsarenotilluminatedthecausemaybeduetothefollowing:
a. AC mains fail.
b. Illuminated master power disconnect circuit breaker is tripped.
 c. AnindividualpoweroutputvoltageswitchissettotheOFFposition(Fig. 1d, pg. 5).
d. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs.
  ToresetthePTC:
  1. SetthevoltageoutputselectorswitchforthatcorrespondingchanneltotheOFFposition.Switchmust
   remainintheOFFpositionforapproximately2minutesinorderforthePTCtoreset(Fig. 1d, pg. 5).
  2. Eliminatethetroublecondition(shortcircuitoroverload).
3. Set the voltage output selector switch for either 24VAC or 28VAC (Fig. 1d, pg. 5).
Alternate 24VAC fixed camera hookup (Fig. 6a, pg. 7).
After completing steps 1-5 of Installation Instructions Remote Accessory Module for use with HubWay, HubWayLD or
HubWayLDH UTP Transceiver Hubs proceed with the following.
1. Setilluminatedmasterpowerdisconnectcircuitbreakertothe(OFF)position(Fig. 4a, pg. 6).
2. ConnectoneendofthecoaxialcabletotheBNCconnectormarked[Video1]onHubSat4Di(Fig. 1a, pg. 5).
Connect the opposite end of the coaxial cable to the BNC video output of camera 1 (Fig. 6a, pg. 7).
3. SetilluminatedmasterpowerdisconnectcircuitbreakertotheRESET(ON)position(Fig. 4a, pg. 6) measure the
 outputvoltageatterminalpairmarked[AUX1]onHubSat4Ditoinsureproperoperationandavoidpossible
damage (Fig. 1c, pg. 5).
4. Connectthepoweroutputterminalpairmarked[AUX1]onHubSat4Ditothepowerinputsofcamera1
(Fig. 1c, pg. 5).Repeatsteps1-3foreachadditionalcamera[AUX2-4].