Installation Instructions

HubSat4Di - 3 -
8. SetilluminatedmasterpowerdisconnectcircuitbreakertotheRESET(ON)position(Fig. 4a, pg. 6). Power
 LEDs(Green)oftheHubSatwillilluminatewhenACpowerispresent(Fig. 1e, pg. 5) and HubWayAv and
HubWayDv Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 5).
9. MeasuretheoutputvoltageateachVideoBalun/Combiner(Figs. 2b, 2d, pg. 6) before making connections to
each camera to ensure proper operation and avoid possible damage.
10. Setilluminatedmasterpowerdisconnectcircuitbreakertothe(OFF)position(Fig. 4a, pg. 6).
11. Connect power outputs of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to power inputs of
cameras (Figs. 2a-2e, pg. 5-6). Polarity must be observed.
 • HubWayAv/HubWayAv2-Terminalsmarked[ACPOWER](Figs. 2a, 2b, 2e, pg. 5-6).
 • HubWayDv-Terminalsmarked[–12VDC+](Figs. 2c, 2d, pg. 5).
12. Connect the terminals marked [+ DATA --]ofHubWayAv,HubWayAv2v or HubWayDv Video Balun/Combiners to
the data input terminals of cameras for PTZ control (Figs. 2b-2d, pg. 5). Polarity must be observed. When using
fixed cameras disregard this step.
13. Connect the BNC connector of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to the BNC video
outputs of cameras (Figs. 2b-2d, pg. 5).
14. SetilluminatedmasterpowerdisconnectcircuitbreakertotheRESET(ON)position(Fig. 4a, pg. 6).
15. ThepowerLEDs(Green)oftheHubSat4DiwillilluminatewhenACpowerispresent(Fig. 1e, pg. 5).
Note:IfanyofthepowerLEDsarenotilluminatedthecausemaybeduetothefollowing:
a. AC mains fail.
b. Illuminated master power disconnect circuit breaker is tripped.
 c. AnindividualpoweroutputvoltageswitchissettotheOFFposition(Fig. 1d, pg. 5).
d. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs.
  ToresetthePTC:
  1. SetthevoltageoutputselectorswitchforthatcorrespondingchanneltotheOFFposition.Switchmust
   remainintheOFFpositionforapproximately2minutesinorderforthePTCtoreset(Fig. 1d, pg. 5).
  2. Eliminatethetroublecondition(shortcircuitoroverload).
3. Set the voltage output selector switch for either 24VAC or 28VAC (Fig. 1d, pg. 5).
HubSat4Di for use as a Remote Accessory Module with HubWay/HubWayLD/HubWayLDH UTP Transceiver Hubs.
After completing steps 1-4 of Installation Instructions for HubSat4Di Passive UTP Transceiver Hub with Integral
Isolated Camera Power proceed with the following.
1. Forfixedcameras,runasingleCAT-5cablebetweenHubSat4DiandHubWay,HubWayLDorHubWayLDHto 
 allowvideotransmissionofuptofour(4)cameras.ForPTZs,runtwo(2)CAT-5cablesbetweenHubSat4Diand
HubWay, HubWayLD or HubWayLDH (Fig. 6, pg. 7).
 a. Connectone(1)oftheCAT-5cablestotheRJ45jackmarked[Video1-4]onHubSat4Di. Connect the
  oppositeendofthisCAT-5cableintotheRJ45jackmarked[CH1-4]ofHubWay,HubWayLDor
HubWayLDH unit (Fig. 6, pg. 7).
 b. Fordata(PTZ),connectthesecondCAT-5cabletotheRJ45jackmarked[Data1-4]onHubSat4Di. Connect
  theoppositeendofthisCAT-5cableintoanyunusedRJ45jackmarked[1-16]ofHubWay,HubWayLDor
HubWayLDH unit (Fig. 6, pg. 7).
Note: Data inputs of HubWay, HubWayLD or HubWayLDH units must be wired in parallel for proper operation.
When using fixed cameras disregard this step.
2. PlugtheRJ45connectoratoneendoftheCAT-5orhigherstructuredcableintotheRJ45jackmarked[PVD1] 
on HubSat4Di (Fig. 1i, pg. 5). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured
cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.
 • For24VACcamerasuseAltronixmodelHubWayAv/HubWayAv2 Video Balun/Combiner (Figs. 2a, 2b, 2e, pg. 5-6).
 • For12VDCcamerasuseAltronixmodelHubWayDvVideoBalun/Combiner(Figs. 2c, 2d, pg. 6).
The total cable distance must not exceed 750 ft. for video transmission between the HubSat4Di and each camera.
 Repeatthisstepforallothercamerachannels[PVD2-4].
3. SetilluminatedmasterpowerdisconnectcircuitbreakertotheRESET(ON)position(Fig. 4a, pg. 6). Power
 LEDs(Green)oftheHubSat4DiwillilluminatewhenACpowerispresent(Fig. 1e, pg. 5) and HubWayAv,
HubWayDv Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 6).
4. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 6) before making connections to
each camera to ensure proper operation and avoid possible damage.
5. Setilluminatedmasterpowerdisconnectcircuitbreakertothe(OFF)position(Fig. 4a, pg. 6).