Installation Instructions

- 2 - HubSat4Di
Overview:
Altronix HubSat4Di Passive UTP Transceiver Hub with Integral Isolated Camera Power transmits UTP video, RS422/
RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 4 camera channels in a wall mount
enclosure. Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or
PTZ cameras when utilizing Altronix HubWayAv or HubWayDv Video Balun/Combiners. In addition, the unit features
individually selectable 24VAC or 28VAC electronically isolated PTC protected outputs with surge suppression. Optionally,
the HubSat4Di can be used as an accessory module to transmit video from up to 4 cameras over a single CAT-5 or higher
structured cable back to the HubWay, HubWayLD or HubWayLDH Passive and Active UTP Transceiver Hubs. In addi-
tion, the HubSat4Di provides power to these cameras locally to eliminate the possibility of voltage drop associated with
long cable runs.
Input:
• 115VAC 50/60Hz, 1.25 amp.
Video:
• Four(4)channelsofqualityvideoovertwistedpair
up to a distance of 750 ft. per channel.
• Four(4)75ohmvideooutputs.
Data:
• RS422/RS485datainput.
Power:
• Individuallyselectable24VACor28VACpower
 outputswithOFFposition.
• Unitprovidesupto1ampmax.perchannelnotto 
exceed a total of 4 amp maximum current.
• Individualelectronicallyisolatedoutputs.
Power (cont.):
• PTCprotectedoutputsare rated @ 1 amp per channel.
• Surgesuppression.
Visual Indicators:
• Four(4) power LED indicators.
Enclosure Dimensions (H x W x D):
8.5”x7.5”x3.5”(215.9mmx190.5mmx88.9mm).
Optional Accessories:
• VideoBalun/Combiners:
- HubWayAv - for use with 24VAC cameras.
- HubWayAv2 - for use with 24VAC cameras.
- HubWayDv - for use with 12VDC cameras.
Specifica tions:
Additional Models:
HubSat42Di
• HubSat4Diw/four(4)HubWayAvVideoBalun/
Combiners for 24VAC Cameras.
HubSat43Di
• HubSat4Diw/four(4)HubWayDvVideoBalun/
Combiners for 12VDC Cameras.
Installation Instructions:
HubSat4Di Passive UTP Transceiver Hub with Integral Isolated Camera Power.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install two fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 8).
Secure green wire lead to earth ground.
2. Setilluminatedmasterpowerdisconnectcircuitbreakertothe[OFF]position(Fig. 4a, pg. 6).
3. Connect 115VAC 50/60Hz to the black and white flying leads of open frame transformer. Secure ground
 wire(Green)toearthground(Fig. 5, pg. 7).ThepowerLEDs(Green)forChannels1-4oftheHubSat4Di
will illuminate when AC power is present (Fig. 1e, pg. 5)
4. S elect 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat4Di (Fig. 4, pg. 6) with the
correspondingoutputvoltageswitches.SelectOFFpositionwhenservicingorinstallingindividualcameras
(Fig. 1d, pg. 5).
5. ConnecttheBNCvideooutputsmarked[Video1-4]onHubSat4Ditothecorrespondingvideoinputsonthe
 headendequipment(DVR)(Fig. 1a, pg. 5).
6. Connect terminals marked [+ Data ---]onHubSat4Di(polaritymustbeobserved)totheRS422/RS485outputofthe
 headendequipment(DVR)(Fig. 1f, pg. 5). When using fixed cameras disregard this step.
7. PlugtheRJ45connectoratoneendoftheCAT-5orhigherstructuredcableintotheRJ45jackmarked[PVD1] 
on HubSat4Di (Fig. 1i, pg. 5). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured
cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.
 • For24VACcamerasuseAltronixmodelHubWayAv/HubWayAv2 Video Balun/Combiner (Figs. 2a, 2b, 2e. pg. 5-6).
 • For12VDCcamerasuseAltronixmodelHubWayDvVideoBalun/Combiner(Figs. 2c, 2d, pg. 5).
The total cable distance must not exceed 750 ft. for video transmission between the HubSat4Di and each camera.
 Repeatthisstepforallothercamerachannels[PVD2-4].