Video • Data • Power Passive UTP Transceiver Hub with Integral Isolated Camera Power Installation Guide Models Include: HubSat4Di - Four (4) Camera Channels HubSat42Di - HubSat4Di w/four (4) HubWayAv Video Balun/Combiners for 24VAC Cameras HubSat43Di - HubSat4Di w/four (4) HubWayDv Video Balun/Combiners for 12VDC Cameras Rev. 090209 More than just power.
Overview: Altronix HubSat4Di Passive UTP Transceiver Hub with Integral Isolated Camera Power transmits UTP video, RS422/ RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 4 camera channels in a wall mount enclosure. Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix HubWayAv or HubWayDv Video Balun/Combiners.
8. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 6). Power LEDs (Green) of the HubSat will illuminate when AC power is present (Fig. 1e, pg. 5) and HubWayAv and HubWayDv Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 5). 9. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 6) before making connections to each camera to ensure proper operation and avoid possible damage. 10.
6. Connect power outputs of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to power inputs of the cameras (Figs. 2a-2e, pg. 5). Polarity must be observed. • HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Figs. 2a, 2b, 2e, pg. 5-6). • HubWayDv/ - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 5). 7. Connect the terminals marked [+ DATA -- ] of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to the data input terminals of cameras for PTZ control (Figs. 2b-2e, pg. 5-6).
Fig. 1 - HubSat4Di Circuit Board 1c - Power Terminals: 24VAC/28VAC power outputs. 1a - BNC Connector: Video in from remote camera video out to DVR. 28VAC 24VAC 24VAC VIDEO1 VIDEO2 AUX3 AUX4 1d - Output Voltage Switches: Selects 24VAC/28VAC/ OFF for each output. 28VAC OFF 28VAC AUX2 OFF AUX1 OFF 28VAC OFF 1b - Output PTCs: Protects each output. 24VAC 24VAC VIDEO3 1e - LED(s) 1-4: Power output indicators. VIDEO4 + DATA - 1i - Channels 1-4: CAT-5 or higher structured cable to cameras.
Fig. 2e HubWayAv2 Power to Camera Cat5 back to HubWay or HubSat Data to Camera Video from Camera ubWayAv/HubWayAv2 passes AC voltage from pins H 4, 5, 7, 8 to terminals marked [AC Power] (Fig. 3, pg. 5). HubWayDv converts AC voltage to DC voltage from pins 4, 5, 7, 8 to terminals marked [-- 12VDC +] (Fig. 3, pg. 5). Fig.
Typical Application Drawing for HubSat4Di as a Passive UTP Transceiver Hub with Integral Camera Power: Fig.
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within the products enclosure that may be of sufficient magnitude to constitute an electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
