Installation Guide

eBridge1PCRMT - 1 -
PLUS
Overview:
The eBridge1PCRM and eBridge1PCTX are CAT5 to Coax cable Ethernet adapters/Media converters
that deliver data and power over the coax cable in a PoE+ compliant format. The paired set enables fast
10/100Base-T Ethernet digital communication to be transmitted over Coax cable. An eBridge1PCRM
receiver is powered by a PoE midspan or endspan product, such as a NetWay8M and NetWay16M and
sends its power over the coax to the eBridge1PCTX transmitter under PoE protocol. This enables the
eBridge1PCRM to be used in a managed manner, allowing for remote camera reset. The eBridge1PCTX
in turn delivers that PoE+ compliant power to a PoE enabled camera or IP device. The eBridge1PCRM
will not deliver power to non-compliant devices, thus avoiding damage to improperly connected analog
cameras. These plug and play units facilitate system upgrades from analog to IP cameras/devices utiliz-
ing existing legacy Coax and eliminating the costs and labor associated with installing new network
cabling. In addition, data transmission and power over the Coax is possible up to 500m in comparison
to 100m Ethernet maximum distance (see Maximum Length of Coax Type vs. Camera Power/PoE Class,
pg. 3). A maximum range from head end to the PoE camera/device is 610m taking into consideration
that up to 100m of structured cable may be deployed at each end.
Features:
Rev. 032113
Installation Guide
eBridge1PCRMT
IP and PoE+ over Coax Solution
eBridge1PCRM Receiver and eBridge1PCTX Transceiver Kit
Agency Listings:
• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
• CE approved.
• C-Tick compliant.
Input:
• Powered by midspan or endspan.
Local Aux. Input Power for eBridge1PCRM:
• 24VDC/110mA or 24VAC/200mA.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5 or better
structured cable.
• Distance: up to 100m.
• Speed: 10/100BaseT, half/full duplex, auto
negotiation. PoE compliant to IEEE 802.3af
(15W) and PoE+ compliant to IEEE 802.3at
(30W) delivered to camera by eBridge1PCTX.
Power provided by eBridge1PCRM to
eBridge1PCTX by PoE protocol.
• Throughput is rated to pass 25mbps of data at
distances up to 500m. With proper headend
equipment this supports Megapixel, HD720,
HD1080.
Coax:
• Distance: up to 500m (see Maximum Length of
Coax Type vs. Camera Power/PoE Class,
pg. 3) for power delivery of coax.
• Connectivity: BNC, RG-59/U or similar.
LED Indicators:
• eBridge1PCRM:
Blue LED - Coax link connection (sloc).
Green - PoE ON.
Green - Power ON.
• eBridge1PCRM and eBridge1PCTX:
Yellow and Green LED (RJ45) IP Link status,
10/100Base-T/active.
LED Indicators (cont’d):
• eBridge1PCTX:
Blue LED - Coax link connection.
Green LED - PoE from eBridge1PCRM.
Environmental:
• Operating Temperature:
eBridge1PCRM:
-- 4ºF to 120.2ºF (-- 20ºC to +49ºC).
eBridge1PCTX:
--- 4ºF to 120.2ºF (-- 20ºC to +49ºC).
• Storage Temperature:
-- 22º to 158ºF (-- 30º to +70ºC)
• Humidity: 20 to 85%, non-condensing.
Functions:
• Auto detection and protection of legacy
non-PoE cameras/devices.
Applications:
• Retrofit digital IP cameras in an analog
CCTV installation.
• Works with Megapixel, HD720, HD1080 and
VGA (SD) cameras (see note, pg. 2).
• Extend Network link distance in an industrial
environment over 610m (see note, pg. 2).
• Upgrade deployed CCTV Coax to a digital
network in Retail, Hospitality, Arenas,
Casinos, Airports, Schools, Hospitals,
Transportation, etc.
Mechanical:
• Dimensions (W x L x H approx.):
eBridge1PCRM:
3.5” x 4.375” x 1”
(88.89mm x 111.125mm x 25.4mm)
eBridge1PCTX:
2.5” x 4.375” x 1”
(63.5mm x 111.125mm x 25.4mm)
I.T.E. 43KC
Z1409